Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM (for Sedan)

DTC    C1403    Rear Speed Sensor RH Malfunction

DTC    C1273    Low Output Signal of Rear Speed Sensor RH (Test Mode DTC)

DTC    C1274    Low Output Signal of Rear Speed Sensor LH (Test Mode DTC)

DTC    C1404    Rear Speed Sensor LH Malfunction


DESCRIPTION

Refer to DTCs C1401 and C1402 .

C151818E11


DTC NO.
DTC Detection Condition
Trouble Area
C1403
C1404
When any of the following is detected:
  1. At a vehicle speed of 10 km/h (6 mph) or more, the output speed signal from one of the speed sensors is equal to or less than 14% of that of one of other 3 sensors for 15 seconds or more.
  2. At a vehicle speed of 10 km/h (6 mph) or more, the output from one of the speed sensors is 0 km/h (0 mph) for 1 second or more.
  3. At a vehicle speed of 10 km/h (6 mph) or more, the outputs from 2 of the speed sensors are 0 km/h (0 mph) for 15 seconds or more.
  1. Rear axle hub and bearing assembly RH/LH (rear speed sensor, speed sensor rotor)
  2. Sensor installation
C1273
C1274
Detected only during Test Mode.
  1. Rear axle hub and bearing assembly RH/LH (rear speed sensor, speed sensor rotor)
  2. Sensor installation

HINT:
  1. DTC C1403 and C1273 are for the rear speed sensor RH.
  2. DTC C1404 and C1274 are for the rear speed sensor LH.


INSPECTION PROCEDURE

NOTICE:
  1. Disassembly of the speed sensor from the rear axle hub and bearing assembly is prohibited.
  2. Check the speed sensor signal after cleaning or replacement (Click here).

1.CHECK REAR SPEED SENSOR INSTALLATION
  1. Turn the ignition switch off.



    C234572E01
  1. Check the speed sensor installation.

    OK:
    There is no clearance between the sensor and the rear axle hub.

    HINT:
    Because the rear axle hub and bearing assembly cannot be disassembled, if the rear speed sensor needs replacement, replace the rear axle hub and bearing assembly.

    Text in Illustration 
    *1
    Rear Speed Sensor
    *a
    No clearance
    *b
    OK
    *c
    NG



NG
REPLACE REAR AXLE HUB AND BEARING ASSEMBLY (Click here)
OK


2.READ VALUE USING TECHSTREAM (REAR SPEED SENSOR)
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.

  1. According to the display on the Techstream, read the Data List.

    ABS/VSC/TRAC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    RR Wheel Speed
    RR wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
    Vehicle stopped:
    0 km/h
    When driving at constant speed: No large fluctuations
    RL Wheel Speed
    RL wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
    Vehicle stopped:
    0 km/h
    When driving at constant speed: No large fluctuations

  1. Check that there is no difference between the speed value output from the speed sensor displayed on the Techstream and the speed value displayed on the speedometer when driving the vehicle.

    HINT:
    Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.

    OK:
    The speed value output from the speed sensor displayed on the Techstream is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



NG
REPLACE REAR AXLE HUB AND BEARING ASSEMBLY (Click here)
OK

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)