REAR AXLE HUB BOLT (for Hatchback) > REPLACEMENT |
| 1. REMOVE REAR WHEEL |
| 2. REMOVE REAR BRAKE DRUM SUB-ASSEMBLY (for Rear Drum Brake) |
| 3. SEPARATE NO. 3 PARKING BRAKE CABLE ASSEMBLY (for Rear Disc Brake) |
![]() |
Separate the No. 3 parking brake cable assembly from the rear disc brake cylinder operation lever.
![]() |
Insert an offset wrench 14 mm at the base of the parking brake cable as shown in the illustration to disengage the clip. Pull out the parking brake cable from the rear disc brake cylinder assembly.
| *1 | No. 3 Parking Brake Cable Assembly |
| *2 | Clip |
| *3 | Offset Wrench 14 mm |
| 4. SEPARATE REAR DISC BRAKE CYLINDER ASSEMBLY (for Rear Disc Brake) |
![]() |
Hold the rear disc brake pad guide pin and remove the 2 bolts and the rear disc brake cylinder assembly.
| 5. REMOVE REAR DISC BRAKE PAD (for Rear Disc Brake) |
![]() |
Remove the 2 disc brake pads from the rear disc brake cylinder mounting.
| 6. REMOVE REAR DISC BRAKE CYLINDER MOUNTING (for Rear Disc Brake) |
![]() |
Remove the 2 bolts and the rear disc brake cylinder mounting from the axle beam.
| 7. REMOVE REAR DISC (for Rear Disc Brake) |
![]() |
Place matchmarks on the rear disc and axle hub, and remove the rear disc.
| *a | Matchmark |
| 8. REMOVE REAR AXLE HUB BOLT |
![]() |
Using SST and a screwdriver or the equivalent, remove the axle hub bolt.
| *A | for Rear Drum Brake |
| *B | for Rear Disc Brake |
| *a | Hold |
| *b | Turn |
| 9. INSTALL REAR AXLE HUB BOLT |
![]() |
Install the washer and the nut onto a new axle hub bolt, as shown in the illustration.
| *A | for Rear Drum Brake |
| *B | for Rear Disc Brake |
| *1 | Washer |
| *2 | Nut |
| *a | Hold |
| *b | Turn |
| Thread Diameter | Thread Pitch |
| 12.0 mm (0.472 in.) | 1.5 mm (0.0591 in.) |
Using a screwdriver or the equivalent to hold the axle hub, install the axle hub bolt by tightening the nut.
| 10. INSTALL REAR DISC (for Rear Disc Brake) |
![]() |
Align the matchmarks of the rear disc and axle hub and install the rear disc.
| *a | Matchmark |
| 11. INSTALL REAR DISC BRAKE CYLINDER MOUNTING (for Rear Disc Brake) |
Install the rear disc brake cylinder mounting to the axle beam with the 2 bolts.
| 12. INSTALL REAR DISC BRAKE PAD (for Rear Disc Brake) |
Install the 2 rear disc brake pads to the rear disc brake cylinder mounting.
| 13. INSTALL REAR DISC BRAKE CYLINDER ASSEMBLY (for Rear Disc Brake) |
![]() |
To compensate for pad wear when reusing the pad, use SST to push and turn the piston (LH side: counterclockwise, RH side: clockwise) to the position where the protrusion on the pad lines up properly with the piston groove.
Hold the rear disc brake pad guide pin, and install the rear disc brake cylinder assembly to the rear disc brake cylinder mounting with the 2 bolts.
| 14. INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY (for Rear Disc Brake) |
Insert the parking brake cable into the disc brake cylinder and engage the clip claws of the parking brake cable to the rear disc brake cylinder guide.
Connect the cable end to the rear disc brake cylinder operation lever.
| 15. INSTALL REAR BRAKE DRUM SUB-ASSEMBLY (for Rear Drum Brake) |
| 16. INSTALL REAR WHEEL |
| 17. INSPECT AND ADJUST PARKING BRAKE LEVER TRAVEL (for Rear Disc Brake) |