Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › FRONT SEAT SIDE AIRBAG ASSEMBLY (for Hatchback Front Passenger Side)

FRONT SEAT SIDE AIRBAG ASSEMBLY (for Hatchback Front Passenger Side) > REMOVAL


CAUTION:
  1. Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (Click here).
  2. If the side airbag was deployed, replace the front seat airbag assembly, separate type front seatback spring assembly, separate type front seatback cover and separate type front seatback pad with a new one.
  3. Wear protective gloves. Sharp areas on the parts may injure your hands.

NOTICE:
Always use "TORX" socket wrench E10 when removing the front seat.



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



3. REMOVE FRONT SEAT INNER BELT ASSEMBLY
(Click here)


4. REMOVE FRONT SEAT HEADREST ASSEMBLY
  1. Remove the front seat headrest assembly.



5. REMOVE RECLINING ADJUSTER RELEASE HANDLE


    B287788E02
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw to remove the reclining adjuster release handle.
    Text in Illustration 
    *a
    Protective Tape



6. REMOVE FRONT SEAT CUSHION SHIELD


    B272755
  1. Disengage the 2 claws to remove the front seat cushion inner shield.



7. REMOVE FRONT SEAT CUSHION INNER SHIELD


    B272755
  1. Disengage the 2 claws to remove the front seat cushion inner shield.



8. REMOVE RECLINING REMOTE CONTROL LEVER SUB-ASSEMBLY (for 3 Door)


    B332517E02
  1. Using a screwdriver with its tip wrapped in protective tape, disengage the claw and 2 guides to remove the cover.
    Text in Illustration 
    *a
    Protective Tape



    B288408
  1. Remove the 2 screws.



    B332535
  1. Disengage the clamp and cable end to remove the reclining remote control lever sub-assembly.



9. REMOVE SEATBACK COVER WITH PAD (for TMC Made)


    B287795
  1. Remove the 3 hog rings.



    B287797
  1. Remove the 3 hog rings.



    B272974
  1. Unfasten the 2 zippers. (for Sport Package)



    B272764
  1. Disengage the 4 claws to remove the 2 front seat headrest supports.



    B349738
  1. Remove the 2 nuts and the front seatback cover bracket. (w/ Front Seat Side Airbag)

  1. Remove the seatback cover with pad from the separate type front setback spring assembly.



10. REMOVE SEATBACK COVER WITH PAD (for TMMF Made)


    B351904
  1. Disengage the 3 hooks.



    B283283
  1. Disengage the 2 hooks.



    B272764
  1. Disengage the 4 claws to remove the 2 front seat headrest supports.



    B349738
  1. Remove the 2 nuts and the front seatback cover bracket. (w/ Front Seat Side Airbag)

  1. Remove the seatback cover with pad from the separate type front setback spring assembly.



11. REMOVE FRONT SEAT SIDE AIRBAG ASSEMBLY


    B290681
  1. Disengage the 3 clamps.



    B272934
  1. Disengage the 2 clamps to separate the front seat side airbag wire harness.



    B287807
  1. Remove the 2 nuts and the front seat side airbag assembly.

    CAUTION:
    1. The nuts must not be reused.
    2. Make sure that the seat frame assembly is not deformed. If it is, replace it with a new one.