Home › Engine / Hybrid System › 1NZ-FE FUEL › FUEL PUMP (for Hatchback)

FUEL PUMP (for Hatchback) > REMOVAL

for Preparation Click here


NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work. (Click here)



1. REMOVE DECK BOARD ASSEMBLY


    B272608
  1. Remove the deck board.



2. REMOVE REAR SEAT ASSEMBLY LH (for 60/40 Split Seat Type)
(Click here)


3. REMOVE REAR SEAT ASSEMBLY RH (for 60/40 Split Seat Type)
(Click here)


4. REMOVE REAR SEAT ASSEMBLY (for Fold Down Seat Type)
(Click here)


5. REMOVE REAR SEATBACK CENTER HINGE SUB-ASSEMBLY (for 60/40 Split Seat Type)


    B282725
  1. Remove the 2 bolts and the rear seatback center hinge sub-assembly.



6. DISCHARGE FUEL SYSTEM PRESSURE
(Click here)


7. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


8. DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY


    A264589E01
  1. Spread the tip of the fuel joint clip, and pull it out in the direction of the arrow.
    Text in Illustration 
    *1
    Fuel Joint Clip
    V100135
    Widen
    V100136
    Pull Out
    V100137
    Pull Out

  1. Disconnect the fuel main tube from the fuel tank assembly.

    NOTICE:
    1. Clean off any dirt or other foreign matter from the clip before beginning work..
    2. The fuel tube joint is sealed by O-rings to the fuel pump tube and the fuel suction plate, so be careful to prevent damage to and foreign matter sticking to the contact surfaces.
    3. Perform installation and removal procedures with your hands only. Never use any tools.
    4. Do not forcibly bend, fold, or twist the nylon tube.
    5. After disconnecting, protect the contact surfaces by covering them with a plastic bag.
    6. If the nylon tube and fuel suction plate are stuck together, push them together and pull them apart to release them.



9. DISCONNECT FUEL TANK VENT HOSE


    A264595E01
  1. Release the retainer as shown in the illustration and disconnect the fuel tank vent hose.
    Text in Illustration 
    *1
    Retainer
    V100135
    Push
    V100136
    Pull

    NOTICE:
    1. Check for dirt or other foreign matter on the parts to be disconnected and clean them if necessary.
    2. The quick connector seals with an O-ring. Ensure that there is no damage or foreign matter on the contact surface.
    3. Do not use any tools.
    4. Do not bend or twist the tubes.
    5. Protect the contact surface by covering it with a plastic bag.
    6. If the connector is stuck, push and pull on the parts to separate them.



10. REMOVE FUEL PUMP GAUGE RETAINER

NOTICE:
Before performing the work, cover the connector of the fuel suction tube assembly and the tube joint with a plastic bag to prevent foreign matter from entering, and then clean off any dirt or other foreign matter.



    A247497E01
  1. Install SST to the fuel pump gauge retainer.

    SST
    09808-14030   (09808-01010, 09808-01020, 09808-01030, 09808-01040, 09808-01050)

    1. Temporarily install plate and claw to the fuel pump gauge retainer.

    2. Press claw against the rib of the fuel pump gauge retainer, and tighten bolt.

    3. Install SST handle.



    A247498E01
  1. While making sure that SST does not rise up, slowly turn handle and loosen the fuel pump gauge retainer.

    NOTICE:
    1. Be careful not to apply excessive downward force to SST, as this may damage the fuel pump or fuel tank.
    2. Turning SST at an angle may cause it to slip off of the fuel pump gauge retainer, so be sure SST is horizontal when turning.
    3. To prevent damage to parts, do not turn SST too vigorously.
    4. If SST slips off of the fuel pump gauge retainer, loosen SST (bolt) and install SST again.

  1. While holding down the fuel suction tube assembly, remove the fuel tank pump gauge retainer.



11. REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY
  1. Remove the fuel suction with pump and gage tube assembly from the fuel tank assembly.

    NOTICE:
    1. Be careful not to bend the arm of the fuel sender gauge assembly.
    2. When installing or removing the fuel suction tube assembly, be careful of fuel splashing.



12. REMOVE FUEL SUCTION TUBE SET GASKET


    A247501
  1. Remove the fuel suction tube set gasket.



13. DRAIN FUEL