Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM (for Hatchback)

ENGINE IMMOBILISER SYSTEM (for Hatchback) > Key Cannot be Registered


DESCRIPTION

A maximum of 5 master key codes and 3 sub key codes (for Mexico) can be registered.

WIRING DIAGRAM

Refer to "System Diagram" (Click here).

INSPECTION PROCEDURE

NOTICE:
When replacing the key and transponder key ECU assembly, refer to the Registration (Click here).

1.CHECK REGISTRATION MODE
  1. Check that the system enters registration mode.

    OK:
    System enters registration mode



NG
Go to step 5
OK


2.CHECK THEFT WARNING INDICATOR LIGHT OPERATION


  1. In the registration mode, when the key inserted in ignition key cylinder, check that the theft warning indicator light assembly.

    HINT:
    If the new key code registration fails, code 2-1 will be output through the theft warning indicator light assembly. Trying to re-register an already registered key will cause code 2-2 to be output when the key is inserted. If the number of registered key codes exceeds the maximum limit, code 2-3 will be output through the theft warning indicator light assembly. The output details are shown below.


    B111593E33

    Result 
    Result
    Proceed to
    Code 2-1
    A
    Code 2-2
    B
    Code 2-3
    C



B
REGISTRATION AS ANOTHER KEY

C
Go to step 3
A


3.READ VALUE USING TECHSTREAM
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Immobiliser / Data List.

  1. According to the display on the Techstream, read the Data List.

    Immobiliser 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Transponder S-code
    Number of registered sub-keys / min.: 0, max.: 15
    Number of registered sub-keys
    -
    Transponder M-code
    Number of registered master keys / min.: 0, max.: 15
    Number of registered master keys
    -
    Result 
    Result
    Proceed to
    None of the below
    A
    Registered master keys: 5, registered sub-keys: 0
    B
    Registered master keys: 0, registered sub-keys: 3
    C
    Registered master keys: 5, registered sub-keys: 3
    D



B
KEY REGISTRATION (SUB-KEY) (Click here)

C
KEY REGISTRATION (MASTER KEY) (Click here)

D
NOT KEY REGISTRATION
A


4.KEY REGISTRATION
  1. Refer to the table below to determine if additional keys can be registered.
    Number of Keys Registered (Master and Sub)
    Proceed to
    0
    New key ID registration
    (Click here)
    1 to 7
    Additional key ID registration
    (Click here)

  1. Check whether key registration.



NG
REPLACE TRANSPONDER KEY ECU ASSEMBLY (Click here)
OK

END (KEY MALFUNCTION) 

5.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
  1. Inspect the unlock warning switch assembly (Click here).



NG
REPLACE UNLOCK WARNING SWITCH ASSEMBLY (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - UNLOCK WARNING SWITCH ASSEMBLY)
  1. Disconnect the D111 unlock warning switch assembly connector.

  1. Disconnect the D139 transponder key ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D111-1 - D139-3 (KSW)
    Always
    Below 1 Ω
    D111-2 - Body ground
    Always
    Below 1 Ω
    D111-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY (Click here)