Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2013.08–2016.04
RM30M0E _58 Vehicle Interior _017115 SUPPLEMENTAL RESTRAINT SYSTEMS _0084736 AIRBAG SYSTEM J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  SRS Warning Light Remains ON  


DESCRIPTION

The SRS warning light is located on the combination meter assembly.

When the SRS is normal, the SRS warning light comes on for approximately 6 seconds after the ignition switch is turned from off to ON, and then goes off automatically.

If there is a malfunction in the SRS, the SRS warning light comes on to inform the driver of a problem.

When terminals TC and CG of the DLC3 are connected, the DTC is displayed by blinking of the SRS warning light.

The SRS is equipped with a voltage-increase circuit (DC-DC converter) in the airbag ECU assembly in case the source voltage drops.

When the battery voltage drops, the voltage-increase circuit (DC-DC converter) functions to increase the voltage of the SRS to normal voltage. In addition, when the voltage drops, the SRS warning light will illuminate.

A malfunction in this circuit is not stored in the airbag ECU assembly. The SRS warning light automatically goes off when the source voltage returns to normal.

The signal to illuminate the SRS warning light is transmitted from the airbag ECU assembly to the combination meter assembly through the CAN communication system.

WIRING DIAGRAM

C296312C01
0.083,0.542 1.906,1.167 1.823,0.625 10 false from Ignition or Starter Switch Assembly*1 or No. 2 Ignition Relay*2 0.104,2.323 1.896,2.948 1.792,0.625 10 false from Ignition or Starter Switch Assembly*1 or No. 2 Ignition Relay*2 1.115,2.938 2.021,3.177 0.906,0.24 10 false from Battery 3.094,4.156 4.5,4.542 1.406,0.385 10 false Combination Meter Assembly 3.094,3.979 3.417,4.188 0.323,0.208 10 false F38 2.927,2.865 3.135,3.042 0.208,0.177 10 false 40 2.927,3.438 3.135,3.615 0.208,0.177 10 false 21 3.125,3.521 3.552,3.74 0.427,0.219 10 false ED 3.135,2.948 3.344,3.125 0.208,0.177 10 false B 3.135,2.333 3.542,2.552 0.406,0.219 10 false IG+ 2.177,3.083 2.938,3.292 0.76,0.208 10 false SECURITY 2.271,2.469 2.813,2.677 0.542,0.208 10 false METER 2.198,0.677 2.99,0.885 0.792,0.208 10 false A/BAG-IG2 2.917,2.229 3.125,2.406 0.208,0.177 10 false 39 5.896,0.427 6.104,0.604 0.208,0.177 10 false 21 6.104,0.542 6.385,0.729 0.281,0.188 10 false IG2 5.885,3.271 6.094,3.448 0.208,0.177 10 false 25 5.896,3.854 6.104,4.031 0.208,0.177 10 false 26 6.104,3.354 6.313,3.531 0.208,0.177 10 false E1 6.104,3.948 6.313,4.125 0.208,0.177 10 false E2 4.615,5.094 7.01,5.313 2.396,0.219 10 false *1 w/o Smart Entry and Start System 4.615,5.427 7.01,5.646 2.396,0.219 10 false *2 w/ Smart Entry and Start System 0.781,5.385 3.177,5.604 2.396,0.219 10 false CAN Communication Line 6.104,4.281 6.427,4.49 0.323,0.208 10 false F21 6.104,4.427 6.917,4.813 0.813,0.385 10 false Airbag ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK SRS WARNING LIGHT OPERATION
a.

Check the SRS warning light operation approximately 6 seconds after the ignition switch is turned to ON.


Result:
Result Proceed to
Remains on. A
Illuminates and then goes off. B



A

2.CHECK BATTERY VOLTAGE

B

6.CHECK CAN COMMUNICATION SYSTEM
2.CHECK BATTERY VOLTAGE
a.

Measure the voltage of the battery.

Standard Voltage:

11 to 14 V



Result:
Result Proceed to
OK A
NG (for 1NZ-FE) B
NG (for 2NZ-FE) C



A

3.CHECK CONNECTOR

B

C

3.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connector is properly connected to the airbag ECU assembly.

OK:
:

The connector is properly connected.


HINT:

If the connector is not connected securely, reconnect the connector and proceed to the next inspection.



d.

Disconnect the connector from the airbag ECU assembly.


e.

Check that the terminals of the connector are not damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

4.CHECK WIRE HARNESS (AIRBAG ECU ASSEMBLY - BODY GROUND)

NG

REPLACE WIRE HARNESS

4.CHECK WIRE HARNESS (AIRBAG ECU ASSEMBLY - BODY GROUND)
a.
C126715C09
1.563,0.344 1.906,0.573 0.344,0.229 1.292,1.281 0.854,1.708 true 1.656,1.281 1.219,1.708 true 1.75,1.292 2.188,1.719 true 0.031,0.031 0.313,0.396 0.281,0.365 10 false *a 1.615,0.375 1.99,0.698 0.375,0.323 10 false F21 0.729,1.719 1.135,2.073 0.406,0.354 10 false IG2 1.125,1.729 1.49,2.063 0.365,0.333 10 false E1 2.146,1.729 2.521,2 0.375,0.271 10 false E2
*a Front view of wire harness connector
(to Airbag ECU Assembly)


Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.

Operate all components of the electrical system (defogger, wipers, headlights, blower motor, etc.).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F21-21 (IG2) - Body ground Ignition switch ON 8 to 16 V



e.

Turn the ignition switch off.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F21-25 (E1) - Body ground Always Below 1 Ω
F21-26 (E2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK SRS WARNING LIGHT

NG

REPLACE WIRE HARNESS

5.CHECK SRS WARNING LIGHT
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Disconnect the connector from the airbag ECU assembly.


d.

Turn the ignition switch to ON.


e.

Check the SRS warning light condition.

OK:

After the primary check period, the SRS warning light goes off for approximately 10 seconds and turns back on.


HINT:

The primary check period is approximately 6 seconds after the ignition switch is turned to ON.



Result:
Proceed to
OK
NG



OK

NG

REPLACE COMBINATION METER ASSEMBLY

6.CHECK CAN COMMUNICATION SYSTEM
a.

Use the GTS to check if the CAN communication system is functioning normally.

CAN Bus Check
50007
HINT:
·

Refer to the Bus Check for the CAN communication system.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

The airbag ECU assembly is connected to the CAN communication system. Therefore, before starting troubleshooting, make sure to check that there is no trouble in the CAN communication system.




Result:
Result Proceed to
DTC is not output. A
DTC is output. B



A

7.CHECK BATTERY VOLTAGE

B

7.CHECK BATTERY VOLTAGE
a.

Measure the voltage of the battery.

Standard Voltage:

11 to 14 V



Result:
Result Proceed to
OK A
NG (for 1NZ-FE) B
NG (for 2NZ-FE) C



A

8.CHECK CONNECTOR

B

C

8.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connector is properly connected to the airbag ECU assembly.

OK:
:

The connector is properly connected.


HINT:

If the connector is not connected securely, reconnect the connector and proceed to the next inspection.



d.

Disconnect the connector from the airbag ECU assembly.


e.

Check that the terminals of the connector are not damaged.

OK:
The terminals are not deformed or damaged.:


Result:
Proceed to
OK
NG



OK

9.CHECK WIRE HARNESS (AIRBAG ECU ASSEMBLY - BODY GROUND)

NG

REPLACE WIRE HARNESS

9.CHECK WIRE HARNESS (AIRBAG ECU ASSEMBLY - BODY GROUND)
a.
C126715C10
1.5,0.375 1.844,0.604 0.344,0.229 1.292,1.281 0.854,1.708 true 1.656,1.281 1.219,1.708 true 1.75,1.292 2.188,1.719 true 0.031,0.031 0.313,0.396 0.281,0.365 10 false *a 1.573,0.396 1.948,0.719 0.375,0.323 10 false F21 0.729,1.719 1.135,2.073 0.406,0.354 10 false IG2 1.125,1.729 1.49,2.063 0.365,0.333 10 false E1 2.146,1.729 2.521,2 0.375,0.271 10 false E2
*a Front view of wire harness connector
(to Airbag ECU Assembly)


Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.

Operate all components of the electrical system (defogger, wipers, headlights, heater blower, etc.).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F21-21 (IG2) - Body ground Ignition switch ON 8 to 16 V



e.

Turn the ignition switch off.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F21-25 (E1) - Body ground Always Below 1 Ω
F21-26 (E2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

10.CHECK CONNECTOR

NG

REPLACE WIRE HARNESS

10.CHECK CONNECTOR
a.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



b.

Check that the connector is properly connected to the combination meter assembly.

OK:

The connector is properly connected.


HINT:

If the connector is not connected securely, reconnect the connector and proceed to the next inspection.



c.

Disconnect the connector from the combination meter assembly.


d.

Check that the terminals of the connector are not damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

11.CHECK WIRE HARNESS (COMBINATION METER ASSEMBLY - BODY GROUND)

NG

REPLACE WIRE HARNESS

11.CHECK WIRE HARNESS (COMBINATION METER ASSEMBLY - BODY GROUND)
a.
E191414C06
0.719,1.104 1.208,1.396 0.49,0.292 0.458,3.01 0.615,2.594 true 2.521,3.021 2.688,2.563 true 3,3.052 2.823,2.552 true 0.813,1.167 1.104,1.365 0.292,0.198 10 false F38 3.031,2.979 3.208,3.156 0.177,0.177 10 false B 2.271,2.948 2.531,3.125 0.26,0.177 10 false IG+ 0.25,2.927 0.542,3.104 0.292,0.177 10 false ED 0.344,0.26 0.5,0.438 0.156,0.177 10 false *a
*a Front view of wire harness connector
(to Combination Meter Assembly)


Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F38-39 (IG+) - Body ground Ignition switch ON 11 to 14 V
F38-40 (B) - Body ground Always 11 to 14 V



d.

Turn the ignition switch off.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F38-21 (ED) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

12.CHECK SRS WARNING LIGHT

NG

REPLACE WIRE HARNESS

12.CHECK SRS WARNING LIGHT
a.

Connect the connector to the combination meter assembly.


b.

Turn the ignition switch off.


c.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



d.

Turn the ignition switch to ON.


e.

Check the SRS warning light condition.

OK:

After the primary check period, the SRS warning light goes off for approximately 10 seconds and turns back on.


HINT:

The primary check period is approximately 6 seconds after the ignition switch is turned on.



Result:
Proceed to
OK
NG



OK

NG

REPLACE COMBINATION METER ASSEMBLY