Home › Power Source / Network › 2NZ-FE BATTERY / CHARGING › CHARGING SYSTEM › 2013.08–2016.10
RM30M0E _57 Power Source / Network _017108 2NZ-FE BATTERY / CHARGING _0092352 CHARGING SYSTEM G

2NZ-FE BATTERY / CHARGING  CHARGING SYSTEM  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

NOTICE:

If the battery is weak or if the engine is difficult to start, recharge the battery and perform inspections again before returning the vehicle to the customer.


PROCEDURE

Hide 1. CHECK BATTERY CONDITION

a.

Check the battery for damage and deformation. If severe damage, deformation or leak is found, replace the battery.


b.

Check the electrolyte level in each cell.

·

If the electrolyte level is above the lower line, check the battery voltage when cranking the engine. If the voltage is less than 9.6 V, recharge or replace the battery.


HINT:

Before checking the battery voltage, turn off all the electrical systems (headlights, blower motor, rear defogger, etc.).



c.

Check the voltage.

i.

Turn the ignition switch off and turn on the headlights for 20 to 30 seconds. This will remove the surface charge from the battery.


ii.

Measure the battery voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Positive (+) terminal - Negative (-) terminal 20°C (68°F) 12.5 to 12.9 V


If the voltage is not as specified, charge the battery.



Hide 2.INSPECT BATTERY TERMINAL AND FUSE

a.

Check that the battery terminals are not loose or corroded.

Torque:
Battery positive (+) terminal : 5.4 N*m (55 kgf*cm, 48 in.*lbf)
Battery negative (-) terminal : 5.4 N*m (55 kgf*cm, 48 in.*lbf)

If the terminals are corroded, clean them.


b.

Measure the resistance of the fuses.

Standard resistance:

Below 1 Ω


If the results are not as specified, replace the fuses as necessary.



Hide 16361A 3.INSPECT FAN AND GENERATOR V BELT

Hide 4.INSPECT GENERATOR WITH REGULATOR ASSEMBLY WIRING

a.

Check that the wiring is in good condition.


Hide 5. LISTEN FOR ABNORMAL NOISE FROM GENERATOR WITH REGULATOR ASSEMBLY

a.

Check that the generator with regulator assembly does not emit any abnormal noise while the engine is running.


Hide 6.INSPECT CHARGE WARNING LIGHT CIRCUIT

a.

Turn the ignition switch to ON. Check that the charge warning light comes on.


b.

Start the engine and check that the light goes off.

If the light does not operate as specified, troubleshoot the charge warning light circuit.


Hide 7.INSPECT CHARGING CIRCUIT WITHOUT LOAD

a.
A192620C06
2.302,1.917 2.615,0.844 true 2.542,2.219 2.802,2.427 0.26,0.208 10 false *2 2.677,0.729 2.854,1.052 0.177,0.323 10 false *a 0.333,2.229 0.51,2.552 0.177,0.323 10 false *1 1.302,0.51 1.531,0.719 0.229,0.208 10 false *b 1.292,1.875 1.521,2.083 0.229,0.208 10 false *c
*1 Battery
*2 Generator with Regulator Assembly
*a Terminal B
*b Ammeter
*c Voltmeter


Connect a voltmeter and an ammeter to the charging circuit as follows.

HINT:

If a battery/generator tester is available, connect the tester to the charging circuit in accordance with the manufacturer's instructions.


i.

Disconnect the wire from terminal B of the generator with regulator assembly and connect it to the negative (-) lead of the ammeter.


ii.

Connect the ammeter positive (+) lead to terminal B of the generator with regulator assembly.


iii.

Connect the voltmeter positive (+) lead to terminal B of the generator with regulator assembly.


iv.

Ground the voltmeter negative (-) lead.



b.

Check the charging circuit.

i.

Keep the engine speed at 2000 rpm and check the reading on the ammeter and voltmeter.

Standard current:

10 A or less


Standard voltage:

12.9 to 14.9 V


If the result is not as specified, replace the generator with regulator assembly.

HINT:

If the battery is not fully charged, the ammeter reading will sometimes be more than the standard current.




Hide 8.INSPECT CHARGING CIRCUIT WITH LOAD

a.

With the engine running at 2000 rpm, turn the high beam headlights on and turn the blower switch to the "HI" position.


b.

Check the reading on the ammeter.

Standard current:

30 A or more


If the ammeter reading is less than the standard current, repair the generator with regulator assembly.

HINT:

If the battery is fully charged, the indication will sometimes be less than the standard current. If this is the case, add more electrical load (operate the wipers, rear window defogger, etc.) and check the reading on the ammeter again.