The front pretensioner squib LH circuit consists of the airbag ECU assembly and front seat outer belt assembly LH.
This circuit instructs SRS to deploy when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the front pretensioner squib LH circuit.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Test Mode / Check Mode |
|---|---|---|---|---|
| B1905/74 | Short in Front Pretensioner Squib LH Circuit | ·
The airbag ECU assembly receives a line short circuit signal in the front pretensioner squib LH circuit during primary check. ·
Front pretensioner squib LH malfunction ·
Airbag ECU assembly malfunction |
·
Instrument panel wire ·
Front seat outer belt assembly LH (Front pretensioner squib LH) ·
Airbag ECU assembly |
DTC corresponds to check mode. |
| B1906/74 | Open in Front Pretensioner Squib LH Circuit | ·
The airbag ECU assembly receives an open circuit signal in the front pretensioner squib LH circuit. ·
Front pretensioner squib LH malfunction ·
Airbag ECU assembly malfunction |
·
Instrument panel wire ·
Front seat outer belt assembly LH (Front pretensioner squib LH) ·
Airbag ECU assembly |
DTC corresponds to check mode. |
| B1907/74 | Short to GND in Front Pretensioner Squib LH Circuit | ·
The airbag ECU assembly receives a short circuit to ground signal in the front pretensioner squib LH circuit. ·
Front pretensioner squib LH malfunction ·
Airbag ECU assembly malfunction |
·
Instrument panel wire ·
Front seat outer belt assembly LH (Front pretensioner squib LH) ·
Airbag ECU assembly |
DTC corresponds to check mode. |
| B1908/74 | Short to B+ in Front Pretensioner Squib LH Circuit | ·
The airbag ECU assembly receives a short circuit to B+ signal in the front pretensioner squib LH circuit. ·
Front pretensioner squib LH malfunction ·
Airbag ECU assembly malfunction |
·
Instrument panel wire ·
Front seat outer belt assembly LH (Front pretensioner squib LH) ·
Airbag ECU assembly |
DTC corresponds to check mode. |
Perform the simulation method by selecting check mode (Signal Check) using the GTS.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE
After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road.
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
| *1 | Front Pretensioner Squib LH |
| *2 | Airbag ECU Assembly |
| *3 | Instrument panel wire |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Check that the connectors are properly connected to the front seat outer belt assembly LH and airbag ECU assembly.
The connectors are properly connected.
If the connectors are connected securely, reconnect the connectors and proceed to the next inspection.
Disconnect the connectors from the front seat outer belt assembly LH and airbag ECU assembly.
Check that the terminals of connectors are not damaged.
The terminals are not deformed or damaged.
Check that the instrument panel wire connector (on the front seat outer belt assembly LH side) is not damaged.
The lock button is not disengaged, and the claw of the lock is not deformed or damaged.
Check that the short spring for the instrument panel wire the activation prevention mechanism is not deformed or damaged.
The short spring is not deformed or damaged.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Front Pretensioner Squib LH |
| *2 | Airbag ECU Assembly |
| *a | Front view of wire harness connector
(to Front Seat Outer Belt Assembly LH (Front Pretensioner Squib LH)) |
Connect the connector to the airbag ECU assembly.
Connect SST (resistance 2.1 Ω) to connector C.
Never connect the tester to the front seat outer belt assembly LH (front pretensioner squib LH) for measurement, as this may lead to a serious injury due to airbag deployment.
Do not forcibly insert SST into the terminals of the connector when connecting.
Insert SST straight into the terminals of the connector.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
DTC B1905/74, B1906/74, B1907/74 or B1908/74 is not output.
Codes other than DTCs B1905/74, B1906/74, B1907/74 and B1908/74 may be output at this time, but they are not related to this check.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Front Pretensioner Squib LH |
| *2 | Airbag ECU Assembly |
| *3 | Instrument panel wire |
| *a | Front view of wire harness connector
(to Front Seat Outer Belt Assembly LH (Front Pretensioner Squib LH)) |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Disconnect SST from connector C.
Disconnect the instrument panel wire from the airbag ECU assembly.
Check for a short to B+ in the circuit.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F24-1 (L+) - Body ground | Ignition switch ON | Below 1 V |
| F24-2 (L-) - Body ground | Ignition switch ON | Below 1 V |
Check for an open in the circuit.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F24-1 (L+) - F24-2 (L-) | Always | Below 1 Ω |
Check for a short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F24-1 (L+) - Body ground | Always | 1 MΩ or higher |
| F24-2 (L-) - Body ground | Always | 1 MΩ or higher |
Check for a short in the circuit.
Release the activation prevention mechanism built into connector B.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F24-1 (L+) - F24-2 (L-) | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Front Pretensioner Squib LH |
| *2 | Airbag ECU Assembly |
Restore the released activation prevention mechanism of connector B to the original condition.
Connect the connectors to the front seat outer belt assembly LH and airbag ECU assembly.
Connect the cable to the negative (-) battery terminal.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
DTC B1905/74, B1906/74, B1907/74 or B1908/74 is not output.
Codes other than DTCs B1905/74, B1906/74, B1907/74 / B1908/74 may be output at this time, but they are not related to this check.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG