Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM › 2013.08–2017.10
RM30M0E _58 Vehicle Interior _017117 SEAT BELT _0084737 SEAT BELT WARNING SYSTEM J

SEAT BELT  SEAT BELT WARNING SYSTEM  Driver Side Seat Belt Warning Light does not Operate  


DESCRIPTION

When the ignition switch is ON, the combination meter assembly receives signals from the front seat inner belt assembly (Driver Side). When the seat belt is unfastened, the combination meter assembly flashes the driver side seat belt warning light in the combination meter assembly. When the seat belt is fastened, the combination meter assembly stops flashing the driver side seat belt warning light.

WIRING DIAGRAM

C296314
3.208,1.094 3.406,1.281 0.198,0.188 10 false 2N 4.083,1.083 4.281,1.271 0.198,0.188 10 false 2M 2.5,1.083 2.833,1.281 0.333,0.198 10 false F114 0.802,1.083 1.135,1.281 0.333,0.198 10 false F114 2.156,1.083 2.417,1.271 0.26,0.188 10 false F29 1.188,1.083 1.448,1.271 0.26,0.188 10 false F29 0.906,0.906 1.021,1.052 0.115,0.146 10 false 2 1.25,0.906 1.365,1.052 0.115,0.146 10 false 2 2.229,0.917 2.344,1.063 0.115,0.146 10 false 3 2.604,0.917 2.719,1.063 0.115,0.146 10 false 3 3.26,0.917 3.375,1.063 0.115,0.146 10 false 2 4.135,0.917 4.25,1.063 0.115,0.146 10 false 4 1.177,1.5 2.604,1.927 1.427,0.427 10 false Front Seat Inner Belt Assembly (Driver Side) 0.885,1.281 1.042,1.448 0.156,0.167 10 false *2 2.594,1.271 2.75,1.438 0.156,0.167 10 false *2 2.208,1.271 2.365,1.438 0.156,0.167 10 false *1 1.229,1.271 1.385,1.438 0.156,0.167 10 false *1 3.198,1.844 4.448,2.26 1.25,0.417 10 false Driver Side Junction Block Assembly 5.333,1.885 5.625,2.125 0.292,0.24 10 false F38 5.333,2.031 6.583,2.448 1.25,0.417 10 false Combination Meter Assembly 5.115,0.979 5.302,1.125 0.188,0.146 10 false 24 5.333,1.094 5.521,1.24 0.188,0.146 10 false L 0.292,2.115 1.094,2.323 0.802,0.208 10 false *1: for LHD 0.292,2.396 1.094,2.604 0.802,0.208 10 false *2: for RHD

PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (DRIVER SIDE SEAT BELT)
a.

Connect the GTS DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Driver Side Seat Belt Driver side seat belt warning light OFF or ON Confirm that the vehicle is stopped with the engine idling
Body Electrical > Combination Meter > Active Test
Tester Display
Driver Side Seat Belt
50004 122 12
OK:

Driver side seat belt warning light condition can be switched by Active Test.


Result:
Result
OK
NG




OK

2.INSPECT FRONT SEAT INNER BELT ASSEMBLY (DRIVER SIDE)

NG

REPLACE COMBINATION METER ASSEMBLY

2.INSPECT FRONT SEAT INNER BELT ASSEMBLY (DRIVER SIDE)
a.

Remove the front seat inner belt assembly (driver side).

Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL


b.

Inspect the front seat inner belt assembly (driver side).

Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>INSPECTION

Result:
Result
OK
NG




OK

3.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT ASSEMBLY (DRIVER SIDE) - DRIVER SIDE JUNCTION BLOCK ASSEMBLY AND BODY GROUND)

NG

REPLACE FRONT SEAT INNER BELT ASSEMBLY (DRIVER SIDE)

3.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT ASSEMBLY (DRIVER SIDE) - DRIVER SIDE JUNCTION BLOCK ASSEMBLY AND BODY GROUND)
a.

for LHD

i.

Disconnect the F29 front seat inner belt assembly (Driver Side) connector.


ii.

Disconnect the 2N driver side junction block assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F29-3 - 2N-2 Always Below 1 Ω
F29-3 or 2N-2 - Body ground Always 10 kΩ or higher
F29-2 - Body ground Always Below 1 Ω



iv.

Reconnect the 2N driver side junction block assembly connector.


v.

Reconnect the F29 front seat inner belt assembly (Driver Side) connector.



b.

for RHD

i.

Disconnect the F114 front seat inner belt assembly (Driver Side) connector.


ii.

Disconnect the 2N driver side junction block assembly connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F114-3 - 2N-2 Always Below 1 Ω
F114-3 or 2N-2 - Body ground Always 10 kΩ or higher
F114-2 - Body ground Always Below 1 Ω



iv.

Reconnect the 2N driver side junction block assembly connector.


v.

Reconnect the F114 front seat inner belt assembly (Driver Side) connector.



Result:
Result
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the F38 combination meter assembly connector.


b.

Disconnect the 2M driver side junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
F38-24 (L) - 2M-4 Always Below 1 Ω
F38-24 (L) or 2M-4 - Body ground Always 10 kΩ or higher


Result:
Result
OK
NG



OK

5.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY
a.
C281432C01
1.458,0.146 1.906,0.427 0.448,0.281 1.458,1.635 1.896,1.938 0.438,0.302 1.583,0.198 1.896,0.396 0.313,0.198 10 false 2M 1.594,1.708 1.906,1.906 0.313,0.198 10 false 2N 0.115,0.104 0.427,0.302 0.313,0.198 10 false *a
*a Component without harness connected
(Driver Side Junction Block Assembly)


Remove the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2N-2 - 2M-4 Always Below 1 Ω
2N-2 or 2M-4 - Body ground Always 10 kΩ or higher



Result:
Result
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY