Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2013.08–2016.04
RM30M0E _57 Power Source / Network _017152 NETWORKING _0084784 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Check CAN Bus Lines for Short Circuit (RHD Models)  


DESCRIPTION

There may be a short circuit between the V bus main lines and/or CAN branch lines when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.

Symptom Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of DLC3 is below 54 Ω.
·

Short in CAN main bus line

·

Short in CAN branch line

·

Combination meter assembly

·

Airbag ECU assembly

·

Certification ECU (Smart key ECU assembly)*1

·

Brake actuator assembly

·

ECM

·

No. 2 junction connector

·

No. 1 CAN junction connector



*1: w/ Smart Entry and Start System


WIRING DIAGRAM

E279865E05
0.083,0.083 0.667,0.281 0.583,0.198 10 false V Bus: 0.229,0.625 1.573,0.833 1.344,0.208 10 false x: Suspected Area 3.375,0.125 3.896,0.302 0.521,0.177 10 false 120 Ω 4.521,0.344 5.042,0.521 0.521,0.177 10 false ECM 4.021,0.75 4.542,0.927 0.521,0.177 10 false CANH 2.729,0.75 3.25,0.927 0.521,0.177 10 false CANL 2.906,0.927 3.198,1.104 0.292,0.177 10 false 7 3.073,0.927 3.365,1.104 0.292,0.177 10 false F81 3.833,0.927 4.125,1.104 0.292,0.177 10 false F81 3.823,1.115 4.115,1.292 0.292,0.177 10 false F82 3.063,1.115 3.354,1.292 0.292,0.177 10 false F82 2.844,1.115 3.135,1.292 0.292,0.177 10 false 34 3.365,0.927 3.656,1.104 0.292,0.177 10 false *1 4.125,0.927 4.417,1.104 0.292,0.177 10 false *1 4.125,1.115 4.417,1.292 0.292,0.177 10 false *2 3.375,1.125 3.667,1.302 0.292,0.177 10 false *2 3.667,0.927 3.958,1.104 0.292,0.177 10 false 8 3.604,1.115 3.896,1.292 0.292,0.177 10 false 33 0.927,1.792 1.219,1.969 0.292,0.177 10 false F62 0.927,1.938 2.948,2.135 2.021,0.198 10 false No. 1 CAN Junction Connector 2.948,1.365 3.24,1.542 0.292,0.177 10 false W 4.031,1.365 4.323,1.542 0.292,0.177 10 false BE 0.99,2.927 1.51,3.104 0.521,0.177 10 false CANH 1.021,3.479 1.542,3.656 0.521,0.177 10 false CANL 5.823,2.031 6.344,2.208 0.521,0.177 10 false CANH 5.833,2.583 6.354,2.76 0.521,0.177 10 false CANL 5.885,3.938 6.406,4.115 0.521,0.177 10 false CANH 6.021,4.281 6.542,4.458 0.521,0.177 10 false CANL 5.813,5.979 6.333,6.156 0.521,0.177 10 false CANL 5.813,5.427 6.333,5.604 0.521,0.177 10 false CANH 2.76,6.896 3.281,7.073 0.521,0.177 10 false CANL 4.01,6.896 4.531,7.073 0.521,0.177 10 false CANH 1.448,2.927 1.74,3.104 0.292,0.177 10 false 13 1.448,3.479 1.74,3.656 0.292,0.177 10 false 22 0.188,3.75 0.479,3.927 0.292,0.177 10 false F21 0.188,3.906 1.708,4.115 1.521,0.208 10 false Airbag ECU Assembly 2.063,2.865 2.354,3.042 0.292,0.177 10 false B 2.052,3.563 2.344,3.74 0.292,0.177 10 false W 2.729,2.927 3.021,3.104 0.292,0.177 10 false 4 2.677,3.479 2.969,3.656 0.292,0.177 10 false 15 3,1.583 3.292,1.76 0.292,0.177 10 false 14 3.99,1.583 4.281,1.76 0.292,0.177 10 false 3 4.302,2.021 4.594,2.198 0.292,0.177 10 false 7 4.281,2.583 4.573,2.76 0.292,0.177 10 false 18 5.125,1.938 5.417,2.115 0.292,0.177 10 false L 5.104,2.646 5.396,2.823 0.292,0.177 10 false W 5.604,2.031 5.896,2.208 0.292,0.177 10 false 40 5.615,2.583 5.906,2.76 0.292,0.177 10 false 18 5.594,2.844 5.885,3.021 0.292,0.177 10 false F44 5.594,3 7.125,3.365 1.531,0.365 10 false Certification ECU (Smart Key ECU Assembly)*3 4.302,3.854 4.594,4.031 0.292,0.177 10 false 1 4.281,4.417 4.573,4.594 0.292,0.177 10 false 12 4.906,3.792 5.198,3.969 0.292,0.177 10 false GR 4.948,4.49 5.24,4.667 0.292,0.177 10 false W 5.667,3.854 5.958,4.031 0.292,0.177 10 false 6 5.823,4.417 6.115,4.594 0.292,0.177 10 false 14 6.188,4.49 6.479,4.667 0.292,0.177 10 false F16 6.188,4.625 6.708,4.833 0.521,0.208 10 false DLC3 5.125,6.063 5.417,6.24 0.292,0.177 10 false W 5.146,5.375 5.438,5.552 0.292,0.177 10 false L 4.344,5.344 4.635,5.521 0.292,0.177 10 false 11 4.313,5.521 4.625,5.719 0.313,0.198 10 false A34 4.313,5.885 4.625,6.083 0.313,0.198 10 false A34 4.354,5.719 4.646,5.896 0.292,0.177 10 false 22 3.823,5.26 4.135,5.458 0.313,0.198 10 false F71 3.063,5.25 3.375,5.448 0.313,0.198 10 false F71 2.99,4.813 3.281,4.99 0.292,0.177 10 false 13 3.99,4.813 4.281,4.99 0.292,0.177 10 false 2 2.958,4.99 3.25,5.167 0.292,0.177 10 false W 4.031,4.99 4.323,5.167 0.292,0.177 10 false L 3.667,5.26 3.958,5.438 0.292,0.177 10 false 2 2.844,5.25 3.135,5.427 0.292,0.177 10 false 13 3.073,6.26 3.385,6.458 0.313,0.198 10 false F71 3.823,6.26 4.135,6.458 0.313,0.198 10 false F71 2.844,6.26 3.135,6.438 0.292,0.177 10 false 12 3.667,6.26 3.958,6.438 0.292,0.177 10 false 1 2.958,6.531 3.25,6.708 0.292,0.177 10 false W 4.021,6.521 4.313,6.698 0.292,0.177 10 false G 2.99,6.719 3.281,6.896 0.292,0.177 10 false 31 3.99,6.719 4.281,6.896 0.292,0.177 10 false 32 5.885,6.24 6.198,6.438 0.313,0.198 10 false A35 5.885,6.396 6.875,6.76 0.99,0.365 10 false Brake Actuator Assembly 4.542,7.115 4.854,7.313 0.313,0.198 10 false F38 4.531,7.26 6.365,7.49 1.833,0.229 10 false Combination Meter Assembly 3.406,7.49 3.927,7.667 0.521,0.177 10 false 120 Ω 1.281,5.708 2.99,5.896 1.708,0.188 10 false No. 2 Junction Connector 0.083,6.656 1.917,6.833 1.833,0.177 10 false *1: for Manual Transaxle 0.083,7 1.917,7.177 1.833,0.177 10 false *2: for Automatic Transaxle 0.083,7.333 2.521,7.521 2.438,0.188 10 false *3: w/ Smart Entry and Start System 0.781,7.917 2.823,8.104 2.042,0.188 10 false : CAN Main Bus Line (CANH) 0.792,8.333 2.833,8.521 2.042,0.188 10 false : CAN Main Bus Line (CANL) 3.906,7.896 5.948,8.083 2.042,0.188 10 false : CAN Branch Line (CANH) 3.917,8.323 5.958,8.51 2.042,0.188 10 false : CAN Branch Line (CANL) 5.604,5.979 5.896,6.156 0.292,0.177 10 false 14 5.604,5.427 5.896,5.604 0.292,0.177 10 false 25

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 60 seconds, and then drive the vehicle at a speed of 20 km/h (12 mph) or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR SHORT IN CAN BUS LINES (COMBINATION METER ASSEMBLY - NO. 2 JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C263368C42
1.542,0.427 1.906,0.646 0.365,0.219 1.74,2.406 1.479,2.719 true 1.865,2.417 2.135,2.74 true 0.083,0.073 0.438,0.333 0.354,0.26 10 false *a 1.604,0.469 1.917,0.667 0.313,0.198 10 false F38 1.25,2.76 1.677,2.979 0.427,0.219 10 false CANL 1.969,2.771 2.396,2.99 0.427,0.219 10 false CANH
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F38-32 (CANH) - F38-31 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result Proceed to
OK A
NG (for Manual Transaxle) B
NG (for Automatic Transaxle) C



A

REPLACE COMBINATION METER ASSEMBLY

B

2.CHECK FOR SHORT IN CAN BUS LINES (ECM - NO. 1 CAN JUNCTION CONNECTOR)

C

4.CHECK FOR SHORT IN CAN BUS LINES (ECM - NO. 1 CAN JUNCTION CONNECTOR)
2.CHECK FOR SHORT IN CAN BUS LINES (ECM - NO. 1 CAN JUNCTION CONNECTOR)
a.

Reconnect the F38 combination meter assembly connector.


b.
E271714C06
1.542,0.417 1.969,0.667 0.427,0.25 1.677,2.781 2.021,1.688 true 2.188,1.698 2.469,2.76 true 0.125,0.094 0.438,0.292 0.313,0.198 10 false *a 1.635,0.458 2.094,0.656 0.458,0.198 10 false F81 2.302,2.823 2.917,3.021 0.615,0.198 10 false CANH 1.5,2.833 2.115,3.031 0.615,0.198 10 false CANL
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F81-8 (CANH) - F81-7 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

NG

3.CHECK FOR SHORT IN CAN BUS LINES (NO. 2 JUNCTION CONNECTOR)
3.CHECK FOR SHORT IN CAN BUS LINES (NO. 2 JUNCTION CONNECTOR)
a.

Reconnect the F81*1 or F82*2 ECM connector.

*1: for Manual Transaxle

*2: for Automatic Transaxle



b.
E271709C02
1.51,0.167 2,0.469 0.49,0.302 1.5,2.354 1.99,2.656 0.49,0.302 2.469,1.313 2.75,0.917 true 2.469,1.583 2.75,1.917 true 0.885,4.052 1.198,3.677 true 0.708,3.74 1.042,3.667 true 0.719,3.188 1.042,3.375 true 0.823,2.844 1.188,3.365 true 1.646,0.24 2.104,0.438 0.458,0.198 10 false A34 1.635,2.427 2.094,2.625 0.458,0.198 10 false F71 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 2.802,0.823 3.375,1.052 0.573,0.229 10 false CANH*b 2.802,1.854 3.354,2.073 0.552,0.219 10 false CANL*b 0.156,3.073 0.729,3.271 0.573,0.198 10 false CANH*c 0.167,3.646 0.708,3.854 0.542,0.208 10 false CANL*c 0.26,2.729 0.792,2.948 0.531,0.219 10 false CANH*d 0.302,3.99 0.844,4.188 0.542,0.198 10 false CANL*d
*a Front view of wire harness connector
(to No. 2 Junction Connector)
*b to Brake Actuator Assembly
*c to Combination Meter Assembly
*d to No. 1 CAN Junction Connector


Disconnect the No. 2 junction connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F34-11 (CANH) - F34-22 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Brake actuator assembly
F71-1 (CANH) - F71-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Combination meter assembly
F71-2 (CANH) - F71-13 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher No. 1 CAN junction connector



Result:
Result Proceed to
OK A
NG (No. 1 CAN junction connector main line) B
NG (ECU or sensor branch line) C
NG (Combination meter assembly main line) D



A

REPLACE NO. 2 JUNCTION CONNECTOR

B

5.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 CAN JUNCTION CONNECTOR)

C

6.CHECK FOR SHORT IN CAN BUS LINES (ECU, SENSOR)

D

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (COMBINATION METER ASSEMBLY - NO. 2 JUNCTION CONNECTOR)

4.CHECK FOR SHORT IN CAN BUS LINES (ECM - NO. 1 CAN JUNCTION CONNECTOR)
a.

Reconnect the F38 combination meter assembly connector.


b.
E271715C20
1.49,0.5 1.896,0.75 0.406,0.25 2.271,2.26 2,2.896 true 2.458,2.271 2.75,2.896 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 1.573,0.542 2.031,0.74 0.458,0.198 10 false F82 1.781,2.917 2.396,3.115 0.615,0.198 10 false CANH 2.604,2.917 3.219,3.115 0.615,0.198 10 false CANL
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F82-33 (CANH) - F82-34 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result
OK
NG



OK

NG

3.CHECK FOR SHORT IN CAN BUS LINES (NO. 2 JUNCTION CONNECTOR)
5.CHECK FOR SHORT IN CAN BUS LINES (NO. 1 CAN JUNCTION CONNECTOR)
a.
C290986C04
1.427,0.667 1.906,0.927 0.479,0.26 1.417,1.75 0.667,1 true 1.115,1.729 0.667,1.5 true 1.25,2.031 0.667,2.5 true 1.406,2.042 0.667,2.75 true 1.24,1.74 0.667,1.25 true 0.938,2 0.667,2 true 1.125,2.031 0.667,2.25 true 0.979,1.75 0.667,1.75 true 2.51,1 1.844,1.74 true 2.51,2.5 1.854,2.031 true 0.208,0.219 0.521,0.375 0.313,0.156 10 false *a 0.083,0.917 0.75,1.083 0.667,0.167 10 false CANH*e 1.552,0.708 1.875,0.896 0.323,0.188 10 false F62 0.083,1.667 0.75,1.833 0.667,0.167 10 false CANH*b 0.083,2.167 0.75,2.333 0.667,0.167 10 false CANL*c 0.083,2.417 0.75,2.583 0.667,0.167 10 false CANL*d 0.083,1.167 0.75,1.333 0.667,0.167 10 false CANH*d 0.083,1.417 0.75,1.583 0.667,0.167 10 false CANH*c 0.083,1.917 0.75,2.083 0.667,0.167 10 false CANL*b 0.083,2.667 0.75,2.833 0.667,0.167 10 false CANL*e 2.583,0.917 3.25,1.083 0.667,0.167 10 false CANH*f 2.583,2.417 3.25,2.583 0.667,0.167 10 false CANL*f
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to DLC3
*c to No. 2 Junction Connector
*d to ECM
*e to Airbag ECU Assembly
*f to Certification ECU (Smart Key ECU Assembly)*1


Disconnect the No. 1 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F62-1 (CANH) - F62-12 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher DLC3
F62-2 (CANH) - F62-13 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher No. 2 junction connector
F62-3 (CANH) - F62-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω ECM
F62-4 (CANH) - F62-15 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Airbag ECU assembly
F62-7 (CANH) - F62-18 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Certification ECU (Smart key ECU assembly)*1


*1: w/ Smart Entry and Start System



Result:
Result Proceed to
OK A
NG (Junction connector main line) B
NG (ECU or sensor branch line) C
NG (DLC3 branch line) D
NG (ECM main line) E



A

REPLACE NO. 1 CAN JUNCTION CONNECTOR

B

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR - NO. 1 CAN JUNCTION CONNECTOR)

C

6.CHECK FOR SHORT IN CAN BUS LINES (ECU, SENSOR)

D

REPAIR OR REPLACE CAN BRANCH LINE CONNECTED TO DLC3

E

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (ECM - NO. 1 CAN JUNCTION CONNECTOR)

6.CHECK FOR SHORT IN CAN BUS LINES (ECU, SENSOR)
a.

Reconnect all wire harness connectors (No. 2 junction connector and No. 1 CAN junction connector).


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU (or sensor) to which the short circuited branch line is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.
C152423C13
1.427,0.167 1.854,0.427 0.427,0.26 1.938,0.927 2.354,0.417 true 1.938,1.438 1.49,1.844 true 0.073,0.083 0.385,0.24 0.313,0.156 10 false *1 1.51,0.198 1.969,0.396 0.458,0.198 10 false F16 2.417,0.292 3.031,0.49 0.615,0.198 10 false CANH 1.094,1.792 1.708,1.99 0.615,0.198 10 false CANL
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F16-6 (CANH) - F16-14 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


HINT:

If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU (or sensor), there may be a short in the ECU (or sensor).



Result:
Result
OK
NG



OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BRANCH LINES OR CONNECTOR