Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2013.08–2014.03
RM30M0E _57 Power Source / Network _017152 NETWORKING _0084784 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Check CAN Bus Line for Short to +B (LHD Models)  


DESCRIPTION

There may be a short circuit between one of the CAN bus lines and +B when no resistance exists between terminals 6 (CANH) and 16 (BAT) or 14 (CANL) and 16 (BAT) of the DLC3.

Symptom Trouble Area
No resistance exists between terminals 6 (CANH) and 16 (BAT) or 14 (CANL) and 16 (BAT) of DLC3.
·

Short in CAN main bus line

·

Short in CAN branch line

·

Combination meter assembly

·

Airbag ECU assembly*1

·

Brake actuator assembly*2

·

ECM

·

Certification ECU (Smart Key ECU Assembly)*3

·

Air Conditioning Amplifier Assembly*4

·

No. 1 CAN junction connector



*1: w/ Airbag System

*2: w/ ABS

*3: w/ Smart Entry and Start System

*4: for Automatic Air Conditioning System


WIRING DIAGRAM

E279864E04
0.083,0.083 1,0.281 0.917,0.198 10 false V Bus: 0.292,0.542 1.583,0.76 1.292,0.219 10 false x: Suspected Area 3.385,0.354 3.854,0.552 0.469,0.198 10 false 120 Ω 2.698,0.979 3.167,1.177 0.469,0.198 10 false CANL 4.052,0.979 4.521,1.177 0.469,0.198 10 false CANH 4.51,0.615 4.979,0.813 0.469,0.198 10 false ECM 3.073,1.156 3.344,1.333 0.271,0.177 10 false F81 3.073,1.344 3.344,1.521 0.271,0.177 10 false F82 3.823,1.156 4.094,1.333 0.271,0.177 10 false F81 3.823,1.333 4.094,1.51 0.271,0.177 10 false F82 2.906,1.156 3.083,1.333 0.177,0.177 10 false 7 3.375,1.156 3.604,1.323 0.229,0.167 10 false *1 2.844,1.344 3.094,1.521 0.25,0.177 10 false 34 3.375,1.344 3.604,1.51 0.229,0.167 10 false *2 3.677,1.156 3.854,1.333 0.177,0.177 10 false 8 3.615,1.333 3.865,1.51 0.25,0.177 10 false 33 4.135,1.156 4.365,1.323 0.229,0.167 10 false *1 4.135,1.333 4.365,1.5 0.229,0.167 10 false *2 3.24,1.875 3.49,2.052 0.25,0.177 10 false 14 3.979,1.875 4.229,2.052 0.25,0.177 10 false 3 4.031,1.656 4.281,1.833 0.25,0.177 10 false BE 2.958,1.656 3.208,1.833 0.25,0.177 10 false W 4.302,2.115 4.552,2.292 0.25,0.177 10 false 7 4.281,2.49 4.531,2.667 0.25,0.177 10 false 18 4.99,2.042 5.24,2.219 0.25,0.177 10 false L 4.948,2.74 5.198,2.917 0.25,0.177 10 false W 5.542,2.125 5.792,2.302 0.25,0.177 10 false 40 5.542,2.49 5.792,2.667 0.25,0.177 10 false 18 5.75,2.115 6.208,2.302 0.458,0.188 10 false CANH 5.76,2.49 6.229,2.688 0.469,0.198 10 false CANL 5.354,2.792 5.688,2.969 0.333,0.177 10 false F44 5.344,2.938 7.156,3.281 1.813,0.344 10 false Certification ECU (Smart Key ECU Assembly)*5 0.896,2.021 1.229,2.198 0.333,0.177 10 false F62 0.885,2.188 2.865,2.406 1.979,0.219 10 false NO. 1 CAN Junction Connector 0.99,2.854 1.448,3.042 0.458,0.188 10 false CANH 1.021,3.219 1.49,3.417 0.469,0.198 10 false CANL 1.01,4.792 1.479,4.99 0.469,0.198 10 false CANL 1,4.427 1.458,4.615 0.458,0.188 10 false CANH 1.448,2.854 1.698,3.031 0.25,0.177 10 false 13 1.448,3.219 1.698,3.396 0.25,0.177 10 false 22 2.063,2.792 2.313,2.969 0.25,0.177 10 false B 2.042,3.49 2.292,3.667 0.25,0.177 10 false W 2.729,2.854 2.979,3.031 0.25,0.177 10 false 4 2.667,3.219 2.917,3.396 0.25,0.177 10 false 15 0.125,3.677 0.458,3.854 0.333,0.177 10 false F21 0.115,3.813 1.719,4.021 1.604,0.208 10 false Airbag ECU Assembly*3 4.302,3.594 4.552,3.771 0.25,0.177 10 false 8 4.281,3.958 4.531,4.135 0.25,0.177 10 false 19 4.958,3.521 5.208,3.698 0.25,0.177 10 false V 4.948,4.24 5.198,4.417 0.25,0.177 10 false W 5.531,3.604 5.781,3.781 0.25,0.177 10 false 11 5.531,3.969 5.781,4.146 0.25,0.177 10 false 12 5.75,3.604 6.083,3.781 0.333,0.177 10 false TX+ 5.76,3.969 6.094,4.146 0.333,0.177 10 false TX- 5.875,5.198 6.333,5.385 0.458,0.188 10 false CANH 6.031,5.531 6.5,5.729 0.469,0.198 10 false CANL 5.5,4.281 5.833,4.458 0.333,0.177 10 false F3 5.49,4.438 7.063,4.802 1.573,0.365 10 false Air Conditioning Amplifier Assembly*6 5.667,5.104 5.917,5.281 0.25,0.177 10 false 6 5.719,5.479 5.969,5.656 0.25,0.177 10 false 14 4.906,5.031 5.156,5.208 0.25,0.177 10 false GR 4.948,5.729 5.198,5.906 0.25,0.177 10 false W 4.281,5.469 4.531,5.646 0.25,0.177 10 false 12 4.302,5.104 4.552,5.281 0.25,0.177 10 false 1 6.188,5.729 6.521,5.906 0.333,0.177 10 false F16 6.188,5.875 6.74,6.052 0.552,0.177 10 false DLC3 3.979,5.865 4.229,6.042 0.25,0.177 10 false 6 3.229,5.865 3.479,6.042 0.25,0.177 10 false 17 2.938,6.25 3.188,6.427 0.25,0.177 10 false W 4.031,6.24 4.281,6.417 0.25,0.177 10 false G 3.219,6.521 3.469,6.698 0.25,0.177 10 false 31 3.99,6.531 4.24,6.708 0.25,0.177 10 false 32 1.458,4.427 1.708,4.604 0.25,0.177 10 false 25 1.448,4.802 1.698,4.979 0.25,0.177 10 false 14 2.667,4.792 2.917,4.969 0.25,0.177 10 false 13 2.708,4.427 2.958,4.604 0.25,0.177 10 false 2 2.083,4.354 2.333,4.531 0.25,0.177 10 false L 2.042,5.073 2.292,5.25 0.25,0.177 10 false W 0.063,5.26 0.396,5.438 0.333,0.177 10 false A35 0.063,5.427 1.875,5.646 1.813,0.219 10 false Brake Actuator Assembly*4 2.771,6.719 3.24,6.917 0.469,0.198 10 false CANL 4.01,6.719 4.469,6.906 0.458,0.188 10 false CANH 3.396,7.281 3.865,7.479 0.469,0.198 10 false 120 Ω 4.531,6.917 4.865,7.094 0.333,0.177 10 false F38 4.521,7.073 6.667,7.26 2.146,0.188 10 false Combination Meter Assembly 0.083,5.917 1.906,6.104 1.823,0.188 10 false *1: for Manual Transaxle 0.083,6.25 1.906,6.438 1.823,0.188 10 false *2: for Automatic Transaxle 0.083,6.583 1.906,6.771 1.823,0.188 10 false *3: w/ Airbag System 0.083,6.917 1.906,7.104 1.823,0.188 10 false *4: w/ ABS 0.083,7.25 2.49,7.479 2.406,0.229 10 false *5: w/ Smart Entry and Start System 0.083,7.583 2.792,7.813 2.708,0.229 10 false *6: for Automatic Air Conditioning System 0.802,8.031 2.719,8.198 1.917,0.167 10 false : CAN Main Bus Line (CANH) 0.813,8.438 2.729,8.604 1.917,0.167 10 false : CAN Main Bus Line (CANL) 3.917,8.021 5.76,8.208 1.844,0.188 10 false : CAN Branch Line (CANH) 3.917,8.417 5.708,8.615 1.792,0.198 10 false : CAN Branch Line (CANL)

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 60 seconds, and then drive the vehicle at a speed of 20 km/h (12 mph) or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 1 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 1 CAN junction connector.


b.

Measure the resistance according to the value(s) in the table below.

C275702C53
2,0.167 2.417,0.417 0.417,0.25 5.667,0.167 6.083,0.417 0.417,0.25 6.49,1.792 6.729,2.073 true 1.656,1.563 1.385,1.531 true 1.635,1.708 1.375,1.76 true 1.781,1.5 1.406,1.052 true 1.802,1.75 1.385,2.25 true 1.906,1.5 1.406,0.792 true 1.896,1.76 1.375,2.542 true 2.25,1.51 3.167,0.698 true 2.26,1.75 2.677,2.385 true 2.052,1.5 3.177,0.469 true 2.031,1.771 2.448,2.583 true 2.375,1.75 2.76,2.146 true 2.5,1.75 3.042,1.969 true 2.49,1.51 3.188,1.177 true 2.385,1.51 3.167,0.938 true 0.833,1.438 1.771,1.656 0.938,0.219 10 false CANH*b 0.833,0.938 1.771,1.177 0.938,0.24 10 false CANH*c 3.219,0.604 4.156,0.854 0.938,0.25 10 false CANH*f 4.438,0.094 4.75,0.25 0.313,0.156 10 false *1 0.083,0.083 1.021,0.24 0.938,0.156 10 false *a 0.833,1.677 1.771,1.896 0.938,0.219 10 false CANL*b 0.833,2.198 1.688,2.448 0.854,0.25 10 false CANL*c 2.729,2.313 3.667,2.563 0.938,0.25 10 false CANL*f 6.781,1.99 7.115,2.198 0.333,0.208 10 false BAT 2.083,0.219 2.542,0.417 0.458,0.198 10 false F62 5.75,0.219 6.208,0.417 0.458,0.198 10 false F16 0.833,2.5 1.688,2.75 0.854,0.25 10 false CANL*d 0.833,0.677 1.771,0.917 0.938,0.24 10 false CANH*d 3.219,0.365 4.135,0.563 0.917,0.198 10 false CANH*e 2.51,2.521 3.448,2.771 0.938,0.25 10 false CANL*e 3.219,0.875 4.156,1.125 0.938,0.25 10 false CANH*g 3.229,1.104 4.167,1.354 0.938,0.25 10 false CANH*h 3.094,1.896 4.031,2.146 0.938,0.25 10 false CANL*h 2.813,2.094 3.75,2.344 0.938,0.25 10 false CANL*g
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to DLC3
*c to Brake Actuator Assembly*1 *d to ECM
*e to Airbag ECU Assembly*2 *f to Combination Meter Assembly
*g Certification ECU (Smart Key ECU Assembly)*3 *h Air Conditioning Amplifier Assembly*4


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F62-1 (CANH) - F16-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher DLC3
F62-12 (CANL) - F16-16 (BAT)
F62-2 (CANH) - F16-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Brake actuator assembly*1
F62-13 (CANL) - F16-16 (BAT)
F62-3 (CANH) - F16-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher ECM
F62-14 (CANL) - F16-16 (BAT)
F62-4 (CANH) - F16-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Airbag ECU assembly*2
F62-15 (CANL) - F16-16 (BAT)
F62-6 (CANH) - F16-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Combination meter assembly
F62-17 (CANL) - F16-16 (BAT)
F62-7 (CANH) - F16-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Certification ECU (Smart Key ECU Assembly)*3
F62-18 (CANL) - F16-16 (BAT)
F62-8 (CANH) - F16-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Air Conditioning Amplifier Assembly*4
F62-19 (CANL) - F16-16 (BAT)


*1: w/ ABS

*2: w/ Airbag System

*3: w/ Smart Entry and Start System

*4: for Automatic Air Conditioning System



Result:
Result Proceed to
OK A
NG (ECU or sensor bus line) B
NG (DLC3 branch line) C



A

REPLACE NO. 1 CAN JUNCTION CONNECTOR

B

2.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU, SENSOR)

C

REPAIR OR REPLACE CAN BRANCH LINE CONNECTED TO DLC3

2.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU, SENSOR)
a.

Reconnect the No. 1 CAN junction connector.


b.

Disconnect the ECU or sensor connected to the CAN bus line that is shorted to +B.

HINT:

If the ECU or sensor has multiple connectors, disconnect the connector that includes the CAN bus lines. To determine the ECU or sensor that is connected to the shorted bus line, refer to Terminals of ECU.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU



c.
C152423C14
1.5,0.146 1.99,0.438 0.49,0.292 1.958,0.906 2.271,0.26 true 1.958,1.49 1.583,1.979 true 2.333,1.458 2.635,1.958 true 2.313,0.167 2.729,0.323 0.417,0.156 10 false CANH 1.208,1.896 1.615,2.042 0.406,0.146 10 false CANL 0.156,0.167 0.323,0.313 0.167,0.146 10 false *1 1.646,0.208 1.906,0.365 0.26,0.156 10 false F16 2.698,1.896 3.115,2.052 0.417,0.156 10 false BAT
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F16-6 (CANH) - F16-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F16-14 (CANL) - F16-16 (BAT)


HINT:

If the resistance changes to 6 kΩ or higher when the connector is disconnected from the ECU (or sensor), there may be a short in the ECU (or sensor).



Result:
Result
OK
NG



OK

REPLACE CORRESPONDING ECU OR SENSOR

NG

REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BRANCH LINES OR CONNECTOR