Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) › 2013.08–2017.10
RM30M0E _58 Vehicle Interior _017118 HEATING / AIR CONDITIONING _0086573 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  B1412  Ambient Temperature Sensor Circuit  


DESCRIPTION

The thermistor assembly is installed in the front part of the cooler condenser assembly to detect the ambient temperature and control the air conditioner. The sensor connected to the air conditioning amplifier assembly detects fluctuations in the ambient temperature. This data is used for controlling the room temperature. The sensor sends a signal to the air conditioning amplifier assembly. The resistance of the thermistor assembly changes in accordance with the cooler thermistor temperature (ambient temperature). As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases. The air conditioning amplifier assembly applies a voltage (5 V) to the thermistor assembly and reads voltage changes as changes in the resistance of the thermistor assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory
B1412 Ambient Temperature Sensor Circuit Open or short in thermistor assembly circuit
·

Thermistor assembly

·

Harness or connector between thermistor assembly and air conditioning amplifier assembly

·

Air conditioning amplifier assembly


Memorized
(4 seconds or more)*1

*1: The air conditioning amplifier assembly stores this DTC if the malfunction has occurred for the period of time indicated in the brackets.


HINT:

If the ambient temperature is approximately -52.9°C (-63.22°F) or lower, DTC B1412 may be output even though the system is normal.


WIRING DIAGRAM

E236721E40
2.146,0.448 2.531,0.844 0.385,0.396 10 false 2 2.146,1.396 2.646,1.729 0.5,0.333 10 false 1 5.115,0.448 5.552,0.75 0.438,0.302 10 false 5 5.115,1.406 5.51,1.708 0.396,0.302 10 false 34 5.396,0.542 6.146,0.958 0.75,0.417 10 false TAM 5.396,1.49 6.146,1.833 0.75,0.344 10 false SG-2 1.135,1.938 1.458,2.115 0.323,0.177 10 false A25 1.125,2.104 2.479,2.313 1.354,0.208 10 false Thermistor Assembly 5.052,1.885 5.333,2.063 0.281,0.177 10 false F3 5.052,2.052 6.635,2.521 1.583,0.469 10 false Air Conditioning Amplifier Assembly

PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Data List.


e.

According to the display on the GTS, read the Data List.

Body Electrical > Air Conditioner > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Ambient Temp Sensor Thermistor assembly Min.: -23.30°C (-9.94°F)
Max.: 65.95°C (150.71°F)
Actual ambient temperature displayed -
Body Electrical > Air Conditioner > Data List
Tester Display
Ambient Temp Sensor
50003 121 2
OK:

The display is as specified in the normal condition column.



Result:
Result Proceed to
NG A
OK (When troubleshooting according to Problem Symptoms Table) B
OK (When troubleshooting according to the DTC) C



A

2.INSPECT THERMISTOR ASSEMBLY

B

C

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

2.INSPECT THERMISTOR ASSEMBLY


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (THERMISTOR ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

3.CHECK HARNESS AND CONNECTOR (THERMISTOR ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the A25 thermistor assembly connector.


b.

Disconnect the F3 air conditioning amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F3-5 (TAM) - A25-2 Always Below 1 Ω
F3-34 (SG-2) - A25-1 Always Below 1 Ω
F3-5 (TAM) or A25-2 - Body ground Always 10 kΩ or higher
F3-34 (SG-2) or A25-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR