Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) › 2013.08–2017.10
RM30M0E _58 Vehicle Interior _017118 HEATING / AIR CONDITIONING _0086573 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  B14A2  Driver Side Solar Sensor Short Circuit  


DESCRIPTION

E107008E22
0.542,0.198 2.219,0.448 1.677,0.25 10 Resistance of Photodiode 0.625,0.823 1.083,1.073 0.458,0.25 10 High 0.646,2.417 1.104,2.688 0.458,0.271 10 Low 0.969,2.594 1.49,2.844 0.521,0.25 10 Weak 2.313,2.583 2.865,2.865 0.552,0.281 10 Strong 0.948,2.979 2.688,3.219 1.74,0.24 10 Strength of Solar Radiation

The cooler (solar sensor) thermistor is installed on the upper side of the instrument panel. It detects sunlight to control air conditioning control in AUTO mode. The output voltage from the cooler (solar sensor) thermistor varies in accordance with the amount of sunlight. When the sunlight increases, the output voltage increases. As the sunlight decreases, the output voltage decreases. The air conditioning amplifier assembly detects changes in the output voltage from the cooler (solar sensor) thermistor.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory
B14A2 Driver Side Solar Sensor Short Circuit Short in cooler (solar sensor) thermistor circuit
·

Cooler (solar sensor) thermistor

·

Harness or connector between cooler (solar sensor) thermistor and air conditioning amplifier assembly

·

Air conditioning amplifier assembly


Memorized
(4 seconds or more)*1

*1: The air conditioning amplifier assembly stores this DTC if the malfunction has occurred for the period of time indicated in the brackets.


WIRING DIAGRAM

E266250E12
5.344,1.896 5.76,2.208 0.417,0.313 10 false F3 5.344,2.063 6.885,2.417 1.542,0.354 10 false Air Conditioning Amplifier Assembly 0.167,2.146 2.208,2.469 2.042,0.323 10 false Cooler (Solar Sensor) Thermistor 5.469,0.667 5.885,0.979 0.417,0.313 10 false 10 5.469,1.51 5.885,1.823 0.417,0.313 10 false 33 5.698,1.625 6.188,1.969 0.49,0.344 10 false TSD 1.604,0.667 2.021,0.979 0.417,0.313 10 false 1 1.604,1.51 2.375,1.927 0.771,0.417 10 false 2 1.271,1.625 1.76,1.969 0.49,0.344 10 false SS- 5.698,0.781 6.188,1.125 0.49,0.344 10 false S5-2 1.229,0.781 1.719,1.125 0.49,0.344 10 false SS+ 0.167,1.99 0.583,2.302 0.417,0.313 10 false E1

PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Active Test.


e.

According to the display on the GTS, read the Data List.

Body Electrical > Air Conditioner > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Solar Sensor (D Side) Cooler (solar sensor) thermistor Min: 0
Max: 255
Cooler (solar sensor) thermistor value increase as brightness increases -
Body Electrical > Air Conditioner > Data List
Tester Display
Solar Sensor (D Side)
50003 121 4
OK:

The display is as specified in the normal condition column.



Result:
Result Proceed to
NG A
OK (When troubleshooting according to Problem Symptoms Table) B
OK (When troubleshooting according to the DTC) C



A

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

B

C

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
E281477C01
1.51,0.219 1.917,0.469 0.406,0.25 1.604,1.302 1.365,1.688 true 1.813,1.302 2.031,1.677 true 1.625,0.24 1.938,0.438 0.313,0.198 10 false E1 1.938,1.677 2.365,1.906 0.427,0.229 10 false SS- 1.229,1.688 1.656,1.917 0.427,0.229 10 false SS+ 0.125,0.115 0.552,0.344 0.427,0.229 10 false *a
*a Front view of wire harness connector (to Cooler (Solar Sensor) Thermistor)


Disconnect the cooler (solar sensor) thermistor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E1-1 (SS+) - E1-2 (SS-) Ignition switch off Below 1 V
E1-1 (SS+) - E1-2 (SS-) Ignition switch ON 4.75 to 5.25 V



Result:
Proceed to
OK
NG



OK

3.INSPECT COOLER (SOLAR SENSOR) THERMISTOR

NG

4.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - COOLER (SOLAR SENSOR) THERMISTOR)
3.INSPECT COOLER (SOLAR SENSOR) THERMISTOR
a.

Remove the cooler (solar sensor) thermistor.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>SOLAR SENSOR>REMOVAL


b.

Inspect the cooler (solar sensor) thermistor.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>SOLAR SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPLACE COOLER (SOLAR SENSOR) THERMISTOR

4.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - COOLER (SOLAR SENSOR) THERMISTOR)
a.

Disconnect the F3 air conditioning amplifier assembly connector.


b.

Disconnect the E1 cooler (solar sensor) thermistor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F3-10 (S5-2) - E1-1 (SS+) Always Below 1 Ω
F3-33 (TSD) - E1-2 (SS-) Always Below 1 Ω
F3-10 (S5-2) or E1-1 (SS+) - Body ground Always 10 kΩ or higher
F3-33 (TSD) or E1-2 (SS-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR