Home › Vehicle Interior › DOOR LOCK › KEY REMINDER WARNING SYSTEM › 2013.08–2017.10
RM30M0E _58 Vehicle Interior _017110 DOOR LOCK _0089807 KEY REMINDER WARNING SYSTEM J

DOOR LOCK  KEY REMINDER WARNING SYSTEM  Key Reminder Buzzer does not Sound  


DESCRIPTION

The key reminder warning buzzer sounds when the driver door is opened while the ignition switch is off or ACC. The key reminder warning buzzer is activated when the unlock warning switch signal and the driver door courtesy light switch signal are received by the combination meter assembly.

WIRING DIAGRAM

E277215
2.479,0.333 2.604,0.5 0.125,0.167 10 false 2 3.646,0.333 3.771,0.5 0.125,0.167 10 false 1 3.635,1.427 3.76,1.594 0.125,0.167 10 false 1 3.635,2.583 3.76,2.75 0.125,0.167 10 false 1 5.521,1.438 5.646,1.604 0.125,0.167 10 false 1 5.458,0.313 5.656,0.5 0.198,0.188 10 false 23 5.469,3.563 5.667,3.75 0.198,0.188 10 false 21 4.365,1.417 4.698,1.594 0.333,0.177 10 false *1 4.375,2.563 4.677,2.781 0.302,0.219 10 false *2 2.073,0.729 2.354,0.906 0.281,0.177 10 false F27 0.156,4.167 1.021,4.354 0.865,0.188 10 false *1: for LHD 1.656,2.01 4.729,2.198 3.073,0.188 10 false Front Door Courtesy Light Switch Assembly LH*1 1.656,1.854 1.938,2.031 0.281,0.177 10 false F31 1.604,3.229 4.677,3.417 3.073,0.188 10 false Front Door Courtesy Light Switch Assembly RH*2 1.604,3.052 1.885,3.229 0.281,0.177 10 false F32 0.167,4.469 1.031,4.656 0.865,0.188 10 false *2: for RHD 2.073,0.927 4.302,1.167 2.229,0.24 10 false Unlock Warning Switch Assembly 5.698,0.417 6.563,0.604 0.865,0.188 10 false KSWO 5.698,1.552 6.563,1.74 0.865,0.188 10 false SW 5.698,3.677 6.563,3.865 0.865,0.188 10 false ED 5.302,4.031 5.583,4.208 0.281,0.177 10 false F38 5.292,4.208 7.135,4.385 1.844,0.177 10 false Combination Meter Assembly

PROCEDURE

1.CHECK COMBINATION METER ASSEMBLY (BUZZER OPERATION)
a.

Remove the key from the key cylinder, turn the light control switch on the headlight dimmer switch assembly to the tail position, and open the driver door.

OK:

The light reminder warning buzzer sounds.



HINT:

The key reminder warning system sounds the buzzer built into the combination meter assembly for key reminder warnings. This buzzer is also used for the light reminder warning system. Therefore, check the operation of the combination meter buzzer by checking if the buzzer sounds to inform that the lights are still on.


Result:
Proceed to
OK
NG



OK

2.READ VALUE USING GTS (DRIVER SIDE DOOR)

NG

REPLACE COMBINATION METER ASSEMBLY

2.READ VALUE USING GTS (DRIVER SIDE DOOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Driver Side Door Driver door courtesy light switch signal CLOSE or OPEN CLOSE: Driver door closed
OPEN: Driver door opened
-
Body Electrical > Combination Meter > Data List
Tester Display
Driver Side Door
50003 122 121

OK:

The GTS indicates ON or OFF according to the driver door condition shown in the table.


Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

3.INSPECT UNLOCK WARNING SWITCH ASSEMBLY

B

5.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY LH

C

7.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY RH
3.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
a.

Remove the unlock warning switch assembly.

Click hereVehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>REMOVAL


b.

Inspect the unlock warning switch assembly.

Click hereVehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

REPLACE UNLOCK WARNING SWITCH ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the F38 combination meter assembly connector.


b.

Disconnect the F27 unlock warning switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F27-1 - F38-23 (KSWO) Always Below 1 Ω
F27-2 - Body ground Always Below 1 Ω
F38-21 (ED) - Body ground Always Below 1 Ω
F27-1 or F38-23 (KSWO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY LH
a.

Remove the front door courtesy light switch assembly LH.

Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>REMOVAL


b.

Inspect the front door courtesy light switch assembly LH.

Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY LH - COMBINATION METER ASSEMBLY)

NG

REPLACE FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY LH

6.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY LH - COMBINATION METER ASSEMBLY)
a.

Disconnect the F38 combination meter assembly connector.


b.

Disconnect the F31 front door courtesy light switch assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F31-1 - F38-1 (SW) Always Below 1 Ω
F31-1 - Body ground Always 10 kΩ or higher
F38-1 (SW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY RH
a.

Remove the front door courtesy light switch assembly RH.

Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>REMOVAL


b.

Inspect the front door courtesy light switch assembly RH.

Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY RH - COMBINATION METER ASSEMBLY)

NG

REPLACE FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY RH - COMBINATION METER ASSEMBLY)
a.

Disconnect the F32 front door courtesy light switch assembly RH connector.


b.

Disconnect the F38 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F32-1 - F38-1 (SW) Always Below 1 Ω
F32-1 or F38-1 (SW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR