Home › Suspension › FRONT SUSPENSION › FRONT SHOCK ABSORBER › 2013.08–2016.04
RM30M0E _53 Suspension _017095 FRONT SUSPENSION _0090096 FRONT SHOCK ABSORBER A

FRONT SUSPENSION  FRONT SHOCK ABSORBER  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.REMOVE WINDSHIELD WIPER MOTOR AND LINK

Hide 2.REMOVE FRONT WHEEL

Hide 47313A 3.SEPARATE FRONT FLEXIBLE HOSE (w/ ABS)

Hide 47313A 4.SEPARATE FRONT FLEXIBLE HOSE (w/o ABS)

Hide 5.REMOVE FRONT SHOCK ABSORBER WITH COIL SPRING

a.
C230948C03
2.979,1.448 2.625,1.448 false 2.833,3.563 2.625,3.563 false 1.177,4.177 1.552,4.385 false 3.042,1.354 3.302,1.583 0.26,0.229 10 false *a 2.917,3.427 3.177,3.656 0.26,0.229 10 false *b 0.969,4.031 1.229,4.26 0.26,0.229 10 false *c
*a Jack Point
*b Wooden Block
*c Jack


Support the front axle using a jack and wooden block.


b.
C294133

Remove the 2 nuts and 2 bolts, and separate the front shock absorber with coil spring (lower side) from the steering knuckle.

HINT:

Keep the bolt from rotating while turning the nut.



c.
C285276C01
0.969,1.906 1.281,2.063 0.313,0.156 10 false *a 2.177,0.302 2.49,0.458 0.313,0.156 10 false *b
*a Turn
*b Hold


Using a 6 mm hexagon socket wrench, fix the shock absorber rod in place and remove the nut.


d.

Remove the front No. 2 suspension support.


e.

Remove the front shock absorber with coil spring from the vehicle.


Hide 48520 6.REMOVE FRONT SHOCK ABSORBER ASSEMBLY

a.
C291493E01
2.542,1.042 2.875,1.042 false 2.938,0.958 3.302,1.146 0.365,0.188 10 false SST

Secure SST in a vise.

SST
09727-30021  (09727-00010, 09727-00021, 09727-00031)


b.

Temporarily install the front shock absorber with coil spring to SST.


c.
C275706C10
0.208,0.208 0.521,0.365 0.313,0.156 10 false *a 0.281,2.771 0.594,2.927 0.313,0.156 10 false *b
*a Correct
*b Incorrect


Attach the arm of SST to the diameter of the front coil spring.

CAUTION:
·

Make sure that the front coil spring is installed so that the distance between the upper and lower hooks of SST is at the maximum.

·

Make sure that the claws of the hooks are securely attached.




d.

Using SST, compress the front coil spring.

CAUTION:
·

If the front coil spring bends during the compression, immediately stop the compression and reinstall SST.

·

Do not compress the spring until the coil springs contact each other.

·

Do not use an impact wrench. It will damage SST.




e.
C291492C01
2.635,1.896 2.854,2.094 0.219,0.198 10 true *a 0.74,1.771 0.958,1.969 0.219,0.198 10 true *b
*a Turn
*b Hold


Confirm that the front coil spring becomes free and using a 6 mm hexagon socket wrench, hold the front shock absorber rod and remove the front support to front shock absorber nut.

CAUTION:

Do not remove the front support to front shock absorber nut when the front coil spring is not free.



f.

Remove the front suspension support sub-assembly from the front shock absorber assembly.


g.

Remove the strut mounting bearing from the front shock absorber assembly.


h.

Remove the front upper coil spring seat from the front shock absorber assembly.


i.

Remove the front spring bumper from the front shock absorber assembly.


j.

Remove the front shock absorber assembly.


k.

Remove the front coil spring from SST.

NOTICE:

Do not use an impact wrench. It will damage SST.