Home › Suspension › REAR SUSPENSION › REAR COIL SPRING › 2013.08–2017.10
RM30M0E _53 Suspension _017096 REAR SUSPENSION _0090104 REAR COIL SPRING A

REAR SUSPENSION  REAR COIL SPRING  REMOVAL  


PROCEDURE

Hide 1.REMOVE REAR WHEELS

Hide 89516D 3.SEPARATE SKID CONTROL SENSOR WIRE LH (w/ ABS)

a.
C282356

Using a screwdriver, disengage the claw of the connector lock portion and disconnect the skid control sensor wire connector.


b.
C285108

Remove the nut and separate the skid control sensor wire LH from the rear axle beam assembly.


Hide 89516C 4.SEPARATE SKID CONTROL SENSOR WIRE RH (w/ ABS)

HINT:

Use the same procedure described for the LH side.


Hide 47319F 5.SEPARATE REAR FLEXIBLE HOSE LH

a.
C282501

Using a 10 mm union nut wrench, separate the rear No. 4 brake tube while holding the rear flexible hose LH with a wrench.

NOTICE:
·

Do not kink or damage the brake line.

·

Do not allow any foreign matter such as dirt and dust to enter the brake line.




b.

Remove the clip and separate the rear flexible hose LH from the rear axle beam assembly.


c.

Remove the nut and separate the rear No. 4 brake tube.


Hide 47318F 6.SEPARATE REAR FLEXIBLE HOSE RH

HINT:

Use the same procedure described for the LH side.


Hide 46430 7.SEPARATE NO. 3 PARKING BRAKE CABLE ASSEMBLY

a.
C285109

Remove the nut and separate the No. 3 parking brake cable assembly.


Hide 46420 8.SEPARATE NO. 2 PARKING BRAKE CABLE ASSEMBLY

HINT:

Use the same procedure described for the No. 3 parking brake cable assembly.


Hide 58251D 9.REMOVE FRONT FLOOR PANEL BRACE LH

a.
C282503

Remove the 3 bolts and front floor panel brace LH from the body.


Hide 58251D 10.REMOVE FRONT FLOOR PANEL BRACE RH

HINT:

Use the same procedure described for the LH side.


Hide 42110F 11.LOOSEN REAR AXLE BEAM ASSEMBLY

a.
C282504C01
0.094,0.052 0.323,0.208 0.229,0.156 10 true *a 1.76,0.052 1.99,0.208 0.229,0.156 10 true *b
*a LH Side
*b RH Side


Loosen the 2 bolts.

NOTICE:

Do not remove the bolts.



Hide 48231B 12.REMOVE REAR COIL SPRING LH

a.

Support the spring seat of the rear axle beam assembly using an engine lifter and 2 wooden blocks.

C282505C01
0.677,2.469 0.958,2.375 false 4.771,1.979 5.031,2.115 true 2.313,2.094 2.542,1.938 true 2.583,1.833 2.823,1.99 0.24,0.156 10 true *a 0.479,2.396 0.792,2.552 0.313,0.156 10 false *b 4.583,1.906 4.781,2.063 0.198,0.156 10 true *a
*a Wooden Block *b Engine Lifter



b.

Remove the 2 bolts and separate the rear axle beam assembly from the rear shock absorber assemblies LH and RH.


c.

Slowly lower the rear axle beam assembly using engine lifter and 2 wooden blocks.


d.

Remove the rear coil spring LH, rear upper coil spring insulator LH and rear lower coil spring insulator LH.


e.

Slowly jack up the rear axle beam assembly using engine lifter and 2 wooden blocks, and temporarily tighten the rear axle beam assembly to the rear shock absorber assemblies LH and RH with the 2 bolts.


Hide 48231A 13.REMOVE REAR COIL SPRING RH

HINT:

Use the same procedure described for the LH side.