The torque sensor converts the torque input from the steering wheel into electrical signals and sends them to the power steering ECU assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Return-to-normal Condition | Note |
|---|---|---|---|---|---|
| C1511 | Torque Sensor Circuit Malfunction | A torque sensor (TRQ1) signal error or a loss of the signal. | ·
Torque sensor (electric power steering column sub-assembly) ·
Power steering ECU assembly |
Ignition switch turned to ON again | Power Steering Warning Light comes on. |
| C1512 | Torque Sensor Circuit Malfunction | A torque sensor (TRQ2) signal error or a loss of the signal. | ·
Torque sensor (electric power steering column sub-assembly) ·
Power steering ECU assembly |
Ignition switch turned to ON again | Power Steering Warning Light comes on. |
| C1513 | Torque Sensor Circuit Malfunction | Deviation between torque sensor TRQ1 and TRQ2 exceeds the specified value. | ·
Torque sensor (electric power steering column sub-assembly) ·
Power steering ECU assembly |
Ignition switch turned to ON again | Power Steering Warning Light comes on. |
| C1514 | Torque Sensor Power Supply Abnormal | A torque sensor power source voltage error. | ·
Torque sensor (electric power steering column sub-assembly) ·
Power steering ECU assembly |
Ignition switch turned to ON again | Power Steering Warning Light comes on. |
| C1517 | Torque Hold Abnormal | Temporary control due to malfunction related to torque sensor continues for long time. | ·
Torque sensor (electric power steering column sub-assembly) ·
Power steering ECU assembly |
Ignition switch turned to ON again | Power Steering Warning Light comes on. |
If the power steering ECU assembly, electric power steering column sub-assembly or power steering motor assembly have been replaced, perform torque sensor zero point calibration.
Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION
| *a | Component with harness connected
(Power Steering ECU Assembly) |
Check the connection condition of the torque sensor (electric power steering column sub-assembly) connector.
Torque sensor connector (electric power steering column sub-assembly) is securely connected to the power steering ECU assembly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch to ON.
| *a | Component with harness connected
(Power Steering ECU Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| z5-8 (TRQV) - z5-2 (TRQG) | Ignition switch ON | 4.5 to 5.5 V |
When the value is within the specified range, record the value.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch to ON.
| *a | Component with harness connected
(Power Steering ECU Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z5-9 (TRQ1) - z5-2 (TRQG) | Engine running, steering wheel not turned (without load) | 2.3 to 2.7 V |
| Engine running, steering wheel turned to right with vehicle stopped | 2.5 to 3.8 V | |
| Engine running, steering wheel turned to left with vehicle stopped | 1.2 to 2.5 V | |
| z5-1 (TRQ2) - z5-2 (TRQG) | Engine running, steering wheel not turned (without load) | 2.3 to 2.7 V |
| Engine running, steering wheel turned to right with vehicle stopped | 1.2 to 2.5 V | |
| Engine running, steering wheel turned to left with vehicle stopped | 2.5 to 3.8 V |
Calculate the difference between the value recorded when measuring the voltage at terminal TRQV in the previous step, and the sum of the output of torque sensor 1 and torque sensor 2.
0.3 V or less (Absolute value)
| Proceed to |
|---|
| OK |
| NG |
OK
NG