Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM › 2013.08–2017.10
RM30M0E _55 Steering _017103 POWER ASSIST SYSTEMS _0090108 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C1524  Motor Circuit Malfunction  C1555  Motor Relay Welding Failure  


DESCRIPTION

The power steering ECU assembly supplies current to the power steering motor assembly through the motor circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Return-to-normal Condition Note
C1524 Motor Circuit Malfunction A short (or open) in the motor circuit or abnormal voltage or current in the motor circuit.
·

EPS fuse

·

Power steering motor assembly

·

Power steering ECU assembly


Ignition switch turned to ON again Power Steering Warning Light comes on.
C1555 Motor Relay Welding Failure A motor relay circuit malfunction.
·

EPS fuse

·

Power steering motor assembly

·

Power steering ECU assembly


Ignition switch turned to ON again Power Steering Warning Light comes on.

WIRING DIAGRAM

C280666E01
4.99,0.302 5.135,0.49 0.146,0.188 10 false 1 4.979,0.5 5.167,0.698 0.188,0.198 10 false z4 4.99,1.083 5.167,1.271 0.177,0.188 10 false 2 4.99,1.302 5.177,1.5 0.188,0.198 10 false z4 4.99,2.417 5.135,2.604 0.146,0.188 10 false 1 5,3.396 5.177,3.583 0.177,0.188 10 false 2 4.927,2.646 5.198,2.844 0.271,0.198 10 false F11 4.938,3.604 5.208,3.802 0.271,0.198 10 false F11 0.542,2.625 1.385,2.833 0.844,0.208 10 false from Battery 2.323,2.823 2.719,3.031 0.396,0.208 10 false EPS 2.531,1.875 4.573,2.083 2.042,0.208 10 false Power Steering Motor Assembly 5.302,0.5 5.563,0.688 0.26,0.188 10 false M1 5.302,1.292 5.563,1.479 0.26,0.188 10 false M2 5.323,2.656 5.625,2.844 0.302,0.188 10 false PIG 5.323,3.604 5.792,3.833 0.469,0.229 10 false PGND 5.031,4.167 7.042,4.417 2.01,0.25 10 false Power Steering ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

If the power steering ECU assembly, electric power steering column sub-assembly or power steering motor assembly have been replaced, perform torque sensor zero point calibration.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (POWER STEERING MOTOR ASSEMBLY- POWER STEERING ECU ASSEMBLY)
a.
C285239C02
1.469,0.229 1.729,0.406 0.26,0.177 0.198,0.188 0.406,0.375 0.208,0.188 10 false *a 1.521,0.229 1.74,0.448 0.219,0.219 10 false z4
*a Component with harness connected
(Power Steering ECU Assembly)


Check the connection condition of the power steering motor assembly connector.

OK:

Power steering motor assembly connector is securely connected to the power steering ECU assembly.



Result:
Proceed to
OK
NG



OK

2.INSPECT POWER STEERING ECU ASSEMBLY

NG

CONNECT CONNECTOR SECURELY

2.INSPECT POWER STEERING ECU ASSEMBLY
a.
C228663C13
2.26,0.74 2.667,0.969 0.406,0.229 1.458,0.74 1.865,0.969 0.406,0.229 2.281,1.604 2.896,2.396 true 1.802,1.615 1.938,2.396 true 1.469,1.604 1.125,2.396 true 2.719,2.427 3.385,2.604 0.667,0.177 10 false PGND 1.865,2.417 2.313,2.625 0.448,0.208 10 false M1 1.573,0.76 1.771,0.927 0.198,0.167 10 false z4 0.177,0.094 0.365,0.26 0.188,0.167 10 false *a 1.031,2.417 1.49,2.615 0.458,0.198 10 false M2 2.302,0.76 2.604,0.927 0.302,0.167 10 false F11
*a Component with harness connected
(Power Steering ECU Assembly)


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z4-1 (M1) - F11-2 (PGND) Ignition switch ON, steering wheel turned to right 11 to 14 V
Ignition switch ON, steering wheel turned to left 6 to 11 V
z4-2 (M2) - F11-2 (PGND) Ignition switch ON, steering wheel turned to right 6 to 11 V
Ignition switch ON, steering wheel turned to left 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT POWER STEERING MOTOR ASSEMBLY

NG

4.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - BODY GROUND)
3.INSPECT POWER STEERING MOTOR ASSEMBLY
a.
C228664C02
1.531,0.969 1.938,1.198 0.406,0.229 1.385,2.188 1.156,2.708 true 2.063,2.198 2.229,2.729 true 1.646,0.99 1.844,1.177 0.198,0.188 10 false z4 1.031,2.729 1.271,2.906 0.24,0.177 10 false M1 2.167,2.74 2.406,2.917 0.24,0.177 10 false M2 0.177,0.135 0.365,0.313 0.188,0.177 10 false *a
*a Front view of wire harness connector
(to Power Steering ECU Assembly)


Disconnect the power steering motor assembly connector from the power steering ECU assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z4-1 (M1) - z4-2 (M2) Always 0.1 to 1.0 Ω
z4-1 (M1) - Body ground Always 1 MΩ or higher
z4-2 (M2) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - BODY GROUND)

NG

REPLACE POWER STEERING MOTOR ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - BODY GROUND)
a.
C231999C07
2.917,2.406 3.323,2.635 0.406,0.229 1.719,2.531 2.198,2.531 true 1.583,3.01 2.583,2.521 true 3.01,2.438 3.333,2.615 0.323,0.177 10 false F11 1.313,2.917 1.823,3.104 0.51,0.188 10 false PIG 1.292,2.438 1.948,2.635 0.656,0.198 10 false PGND 0.177,0.115 0.365,0.292 0.188,0.177 10 false *a
*a Rear view of wire harness connector
(to Power Steering ECU Assembly)


Disconnect the power steering ECU assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F11-1 (PIG) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F11-2 (PGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR