Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM › 2013.08–2017.10
RM30M0E _55 Steering _017103 POWER ASSIST SYSTEMS _0090108 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C1552  PIG Power Supply Voltage Malfunction  C1554  Power Supply Relay Failure  


DESCRIPTION

When a problem occurs in the system, the power source relay circuit and the motor relay circuit are shut off to stop the power assist. The ECU must be replaced when there is a problem with the relays because each relay is built into the ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area Return-to-normal Condition Note
C1552 PIG Power Supply Voltage Malfunction A PIG power source circuit malfunction.
·

EPS fuse

·

PIG power source circuit

·

Power steering ECU assembly


Ignition switch turned to ON again or after system confirmed to be normal Power Steering Warning Light comes on.
C1554 Power Supply Relay Failure A power source relay circuit malfunction.
·

EPS fuse

·

PIG power source circuit

·

Power steering ECU assembly


Ignition switch turned to ON again Power Steering Warning Light comes on.

WIRING DIAGRAM

C280667E01
0.771,0.719 1.656,0.979 0.885,0.26 10 false from Battery 2.625,0.906 3,1.219 0.375,0.313 10 false EPS 4.583,3.198 6.635,3.458 2.052,0.26 10 false Power Steering ECU Assembly 4.594,2.208 5.042,2.448 0.448,0.24 10 false PGND 4.604,0.729 4.979,1.042 0.375,0.313 10 false PIG 4.583,2.99 5.052,3.208 0.469,0.219 10 false F11 4.344,0.573 4.5,0.813 0.156,0.24 10 false 1 4.344,2.01 4.5,2.25 0.156,0.24 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

If the power steering ECU assembly, electric power steering column sub-assembly or power steering motor assembly have been replaced, perform torque sensor zero point calibration.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.READ VALUE USING GTS (PIG POWER SUPPLY)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / EMPS / Data List.


f.

Select the item PIG Power Supply in the Data List and read the value displayed on the GTS.

Chassis > EMPS > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
PIG Power Supply Power source voltage to activate motor Min.: 0.0 V
Max.: 25.5 V
11 to 14 V The engine is running and the power steering is operating.
Chassis > EMPS > Data List
Tester Display
PIG Power Supply
50003 13 13
OK:

A value within the range listed in the normal condition column is displayed on the GTS.



Result:
Proceed to
OK
NG



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

2.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - BATTERY AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - BATTERY AND BODY GROUND)
a.
C231999C08
2.917,2.406 3.323,2.635 0.406,0.229 1.802,2.5 2.281,2.5 true 1.615,2.979 2.615,2.49 true 3,2.427 3.292,2.594 0.292,0.167 10 false F11 1.354,2.875 1.865,3.063 0.51,0.188 10 false PIG 1.385,2.406 2.042,2.604 0.656,0.198 10 false PGND 0.177,0.115 0.365,0.292 0.188,0.177 10 false *a
*a Rear view of wire harness connector
(to Power Steering ECU Assembly)


Disconnect the power steering ECU assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F11-1 (PIG) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F11-2 (PGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR