Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2013.08–2016.04
RM30M0E _54 Brake _017098 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0090184 ANTI-LOCK BRAKE SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  TS and CG Terminal Circuit  


DESCRIPTION

In Test Mode (signal check), a malfunction in the speed sensor that cannot be detected when the vehicle is stopped can be detected while driving.

Sensor check mode can be entered by connecting terminals 12 (TS) and 4 (CG) of the DLC3 and turning the ignition switch from off to ON.

WIRING DIAGRAM

C280158E08
0.938,0.948 1.25,1.146 0.313,0.198 10 false TS 5.552,0.927 5.865,1.125 0.313,0.198 10 false TS 0.927,1.813 1.24,2.01 0.313,0.198 10 false CG 1.26,0.792 1.573,0.99 0.313,0.198 10 false 12 1.281,1.667 1.594,1.865 0.313,0.198 10 false 4 5.469,2.927 5.781,3.125 0.313,0.198 10 false A35 5.198,0.781 5.51,0.979 0.313,0.198 10 false 32 5.469,3.083 7.021,3.448 1.552,0.365 10 false Skid Control ECU (Brake Actuator Assembly) 0.354,2.948 0.667,3.146 0.313,0.198 10 false F16 0.365,3.135 0.792,3.333 0.427,0.198 10 false DLC3

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (TS of DLC3 - SKID CONTROL ECU)
a.

Disconnect the A35 skid control ECU (brake actuator assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F16-12 (TS) - A35-32 (TS) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)
a.
C280109C41
1.542,0.146 1.917,0.417 0.375,0.271 1.604,0.802 1.177,0.385 true 0.104,0.083 0.417,0.24 0.313,0.156 10 false *1 0.938,0.292 1.25,0.49 0.313,0.198 10 false CG 1.615,0.208 1.906,0.365 0.292,0.156 10 false F16
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F16-4 (CG) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (TS - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (TS - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F16-12 (TS) or A35-32 (TS) - Body ground Always 10 kΩ or higher


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next suspected area before replacing the part.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR