Be sure that the ignition switch is off if you work near the electric cooling fans or radiator grille. With the ignition switch ON, the electric cooling fans may automatically start to run if the engine coolant temperature is high and/or the air conditioning is on.
81150
1.REMOVE HEADLIGHT ASSEMBLY LH
81150
2.REMOVE HEADLIGHT ASSEMBLY RH
Use the same procedure as for the LH side.
89173
3.REMOVE FRONT AIRBAG SENSOR (w/ Airbag System)
4.DRAIN ENGINE COOLANT
53510
5.REMOVE HOOD LOCK ASSEMBLY
53215B
6.REMOVE HOOD LOCK SUPPORT
Disengage the clamp to disconnect the wire harness from the hood lock support.
Remove the 2 bolts and hood lock support from the radiator support assembly.
88891H
7.REMOVE NO. 1 COOLER COVER (w/o Fan Shroud Ventilation Duct)
53216A
8.REMOVE UPPER RADIATOR SUPPORT
Disengage the clamp to separate the hood lock control cable assembly from the upper radiator support.
Disengage the 2 clamps to disconnect the wire harness from the upper radiator support.
Disconnect the low pitched horn assembly connector.
Remove the 4 bolts and upper radiator support from the radiator support assembly.
16750
9.REMOVE FAN SHROUD VENTILATION DUCT ASSEMBLY (w/ Fan Shroud Ventilation Duct)
Disengage the 2 claws and 2 guides to remove the fan shroud ventilation duct assembly from the radiator assembly.
10.DISCONNECT RADIATOR RESERVOIR TANK HOSE
Disconnect the radiator reservoir tank hose from the water filler sub-assembly.
16573B
11.DISCONNECT NO. 3 RADIATOR HOSE
Loosen the hose clip and disconnect the No. 3 radiator hose from the radiator assembly.
16572D
12.DISCONNECT NO. 2 RADIATOR HOSE
Loosen the hose clip and disconnect the No. 2 radiator hose from the radiator assembly.
32942
13.DISCONNECT OUTLET NO. 1 OIL COOLER HOSE (for Automatic Transaxle)
Loosen the hose clip and disconnect the outlet No. 1 oil cooler hose from the radiator assembly.
32941
14.DISCONNECT INLET NO. 1 OIL COOLER HOSE (for Automatic Transaxle)
Loosen the hose clip and disconnect the inlet No. 1 oil cooler hose from the radiator assembly.
16400
15.REMOVE RADIATOR ASSEMBLY (w/ Cooler System)
Disconnect the cooling fan motor connector.
Disengage the 3 clamps to disconnect the wire harness from the fan shroud.
Disengage the 2 claws and 2 guides to separate the cooler condenser assembly from the radiator assembly.
While tilting the cooler condenser assembly toward the front of the vehicle, separate the cooler condenser assembly from the radiator assembly.
Remove the radiator assembly together with fan shroud from the vehicle.
Do not apply excessive force to the cooler condenser assembly or piping when removing the radiator assembly.
16400
16.REMOVE RADIATOR ASSEMBLY (w/o Cooler System)
Disconnect the cooling fan motor connector.
Disengage the 3 clamps to disconnect the wire harness from the fan shroud.
Remove the radiator assembly together with fan shroud from the vehicle.
16711
17.REMOVE FAN SHROUD
Disengage the 2 claws and 2 guides to remove the fan shroud from the radiator assembly.
16523A
18.REMOVE RADIATOR SUPPORT CUSHION
Remove the 2 radiator support cushions from the radiator assembly.
16535
19.REMOVE LOWER RADIATOR SUPPORT
Remove the 2 lower radiator supports from the radiator assembly.
20.REMOVE RADIATOR DRAIN COCK PLUG
Remove the radiator drain cock plug from the radiator assembly.
Replace the O-ring if it is damaged.