Home › Engine / Hybrid System › 1NZ-FE EMISSION CONTROL › CANISTER › 2013.08–2016.10
RM30M0E _51 Engine / Hybrid System _017077 1NZ-FE EMISSION CONTROL _0090217 CANISTER A

1NZ-FE EMISSION CONTROL  CANISTER  INSTALLATION  


PROCEDURE

Hide 77169A 1.INSTALL FUEL SUCTION TUBE SET GASKET

a.

Apply gasoline to a new fuel suction tube set gasket and install it to the fuel tank assembly.


Hide 77020A 2.INSTALL FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

a.

Pass the float of the fuel suction tube with pump and gauge assembly into the fuel tank assembly.


b.

Bend up the tip of the fuel pump filter and set the fuel suction tube with pump and gauge assembly on the fuel tank assembly.

A305627E02
6.417,1.885 6.875,2.083 0.458,0.198 10 false 60°

NOTICE:

Be careful not to bend the arm of the fuel sender gauge assembly.



c.
A307876C02
1.281,4.25 1.552,4.125 true 2.052,1.24 2.281,1.042 true 1.177,4.25 1.438,4.417 0.26,0.167 10 true *a 2.313,0.938 2.573,1.104 0.26,0.167 10 true *a
*a Groove
V100145

Tab


Align the 2 tabs of the fuel suction tube with pump and gauge assembly with the 2 grooves of the fuel tank assembly.


Hide 3.INSTALL FUEL PUMP GAUGE RETAINER

a.
A307869C01
1.24,2.448 1.604,2.26 false 1.021,1.792 0.771,1.792 false 0.615,0.51 0.885,0.51 false 2.271,1.417 2.563,1.625 false 2.396,3.021 2.625,3.188 false 1.281,3.229 1.469,3.167 false 1.021,3.854 1.135,4.271 1.135,4.271 1.219,3.854 true 2.208,0.219 2.771,0.458 true 1.448,0.927 1.708,0.76 false 0.479,4.292 0.563,4.156 false 1.656,2.208 1.969,2.365 0.313,0.156 10 false *1 0.115,1.458 0.427,1.615 0.313,0.156 10 false *c 0.469,0.438 0.781,0.594 0.313,0.156 10 false *d 0.646,3.844 0.958,4 0.313,0.156 10 false *f 0.427,3.063 0.74,3.219 0.313,0.156 10 false *a 1.083,4.292 1.396,4.448 0.313,0.156 10 false *e 0.125,2.896 0.438,3.052 0.313,0.156 10 false *c 0.125,0.031 0.438,0.188 0.313,0.156 10 false *b 0.625,1.719 0.938,1.875 0.313,0.156 10 false *d 1.531,3.094 1.844,3.25 0.313,0.156 10 false *d 2.219,2.948 2.531,3.104 0.313,0.156 10 false *d 2.094,1.333 2.417,1.521 0.323,0.188 10 false *d 1.469,3.844 1.781,4 0.313,0.156 10 false *f 2.188,4.438 2.5,4.594 0.313,0.156 10 false A 2.031,0.135 2.354,0.323 0.323,0.188 10 false *d 1.74,0.677 2.052,0.833 0.313,0.156 10 false *1 0.354,4.302 0.667,4.458 0.313,0.156 10 false *1
*1 Fuel Pump Gauge Retainer
*a View A
*b Correct
*c Incorrect
*d SST (Claw)
*e Narrow
*f Wide


Temporarily install SST (plate) and SST (claw) to a new fuel pump gauge retainer.

SST
09808-14030  (09808-01030, 09808-01040, 09808-01050)

NOTICE:
·

Install SST (claw) to the correct location.

·

Do not install SST (claw) to a location where the pitch between ribs of the fuel pump gauge retainer is narrow.




b.
A307854C01
1.688,1.073 0.771,1.708 true 0.573,1.646 0.885,1.802 0.313,0.156 10 false *a
*a Center Point of Fuel Pump Gauge Retainer


Adjust the position of SST (claw) so that the hole in SST (plate) for installing SST (handle) is in the center of the fuel pump gauge retainer.


c.
A307870C01
1.531,0.729 1.115,0.469 false 2.01,1.24 2.333,1.24 false 1.906,0.667 2.396,0.396 false 0.948,0.396 1.26,0.552 0.313,0.156 10 false *a 2.375,1.135 2.688,1.292 0.313,0.156 10 false *b 2.448,0.281 2.76,0.479 0.313,0.198 10 false *c
*a SST (Plate)
*b SST (Claw)
*c SST (Bolt)
V100135

Press


Press SST (claw) against the rib of the fuel pump gauge retainer and tighten SST (bolt).


d.
A307855C01
0.792,1.146 1.146,1.365 true 0.667,1.635 0.813,1.573 false 0.854,1.594 1.021,1.823 1.021,1.823 1.146,1.406 true 0.969,1.833 1.281,1.99 0.313,0.156 10 false *c 0.5,1.573 0.813,1.729 0.313,0.156 10 false *b 0.625,1.052 0.844,1.24 0.219,0.188 10 false *a
*a Fuel Pump Gauge Retainer Start of Threads Location
*b Start of Threads Mark Copied to Vehicle Floor
*c Align
V100135

Front Side of Vehicle


Align the start of threads mark on the fuel pump gauge retainer with the start of threads mark that was copied to the vehicle floor as shown in the illustration.


e.
A307856C01
0.875,1.823 1.406,1.625 true 2.26,3.323 2.896,3.427 true 0.667,1.76 0.979,1.917 0.313,0.156 10 false *a 2.927,3.365 3.104,3.552 0.177,0.188 10 true *b 1.885,0.854 2.104,1.073 0.219,0.219 10 false *c 1.01,1.115 1.24,1.271 0.229,0.156 10 false *d 1.292,0.698 1.51,0.917 0.219,0.219 10 true *c 2.125,1.219 2.354,1.375 0.229,0.156 10 false *d 1.115,2.208 1.427,2.406 0.313,0.198 10 false *e
*a SST (Plate)
*b Fuel Pump Gauge Retainer Start of Threads Location
*c Worker A
*d Worker B
*e Approximately 180°
V100135

Press Down
V100136

Slowly Rotate
V100137

Front Side of Vehicle


While one person presses down to prevent the fuel pump gauge retainer and fuel suction tube with pump and gauge assembly from rotating together, the other person should firmly press the fuel pump gauge retainer against the threads of the fuel tank assembly, and tighten it by rotating it approximately 180°.

CAUTION:

Make sure not to pinch your hands with SST.


NOTICE:
·

Be careful not to apply excessive downward force to SST, as this may damage the fuel suction tube with pump and gauge assembly or fuel tank assembly.

·

Turning SST at an angle may cause it to slip off of the fuel pump gauge retainer, so be sure SST is horizontal when turning.

·

To prevent damage to parts, do not turn SST too vigorously.

·

If SST slips off of the fuel pump gauge retainer, loosen SST (bolt) and install SST again.




f.

As shown in the illustration, quickly and firmly press down on the part of the fuel pump gauge retainer closest to the front side of the vehicle so that it no longer rises up.

A307857C01
2.656,0.688 2.906,0.563 false 1.063,2.198 0.927,2.083 false 2.979,2.51 3.115,2.375 false 2.594,3.25 2.792,3.146 false 0.896,3.219 1.083,3.167 false 0.771,2 0.979,2.198 0.208,0.198 10 false *1 0.729,3.177 0.958,3.375 0.229,0.198 10 false *2 2.927,0.479 3.24,0.635 0.313,0.156 10 false *a 3.094,2.219 3.302,2.417 0.208,0.198 10 false *1 2.417,3.208 2.646,3.406 0.229,0.198 10 false *2 5.24,2.5 5.552,2.698 0.313,0.198 10 false *b
*1 Fuel Pump Gauge Retainer *2 Fuel Tank Assembly
*a SST (Plate) *b Fuel Pump Gauge Retainer Rising Up
V100135

Press Quickly and Firmly
V100136

Front Side of Vehicle


HINT:
·

If the fuel pump gauge retainer cannot be properly pressed down due to the position of SST, set SST in a different position.

·

When pressing down the fuel pump gauge retainer, there will be a sound or tactile sensation of parts contacting and pressing together when the fuel pump gauge retainer is fully pressed down, and at this point it will stop rising up.




g.
A307858C01
0.781,3.719 0.375,3.49 true 1.083,3.583 0.771,3.469 true 1.75,2 1.573,1.646 true 1.698,2 2.01,2.156 0.313,0.156 10 false *a 0.604,3.385 0.917,3.542 0.313,0.156 10 false *b 0.208,3.396 0.396,3.583 0.188,0.188 10 true *c 1.26,0.667 1.469,0.854 0.208,0.188 10 true *d 1.031,1.115 1.344,1.271 0.313,0.156 10 false *e 1.917,0.885 2.125,1.073 0.208,0.188 10 true *d 2.135,1.219 2.448,1.375 0.313,0.156 10 false *e 2.042,4.396 2.354,4.594 0.313,0.198 10 false *f
*a SST (Plate)
*b Fuel Pump Gauge Retainer Start of Threads Location
*c Copied Start of Threads Mark
*d Worker A
*e Worker B
*f Rotate to Start of Threads Mark on Vehicle Floor
V100135

Press Down
V100136

Slowly Rotate
V100137

Front Side of Vehicle


While one person presses down to prevent the fuel pump gauge retainer and fuel suction tube with pump and gauge assembly from rotating together, the other person should slowly rotate SST (plate) and tighten the fuel pump gauge retainer until it reaches the start of threads mark that was copied to the vehicle floor.

CAUTION:

Make sure not to pinch your hands with SST.



h.
A307859C01
2.365,0.948 2.813,0.927 true 2.031,1.719 2.125,1.979 true 1.208,1.656 1,1.979 true 1.563,3.26 1.115,3.063 false 1.729,4.031 1.49,4.208 false 2.729,3.094 2.333,3.094 false 0.938,2.969 1.25,3.125 0.313,0.156 10 false *1 1.302,4.156 1.615,4.313 0.313,0.156 10 false *2 0.917,1.99 1.229,2.146 0.313,0.156 10 false *a 2.792,3.01 3.104,3.167 0.313,0.156 10 false *b 2.49,0.302 2.646,0.5 0.156,0.198 10 true A 1.573,0.625 1.729,0.823 0.156,0.198 10 true A 0.458,2.615 0.969,2.875 0.51,0.26 10 true A-A 2.063,2.01 2.375,2.292 0.313,0.281 10 false *a 2.854,0.833 3.135,1.052 0.281,0.219 10 true *a
*1 Fuel Pump Gauge Retainer
*2 Fuel Tank Assembly
*a Measurement Location
*b Vernier Caliper
V100135

Front Side of Vehicle


Check the tightening condition of the fuel pump gauge retainer.

i.

Using a vernier caliper, measure the upper surface of the fuel tank assembly in the 3 locations shown in the illustration.

Specification:

Difference between the 3 measured values is within 3 mm.


NOTICE:

If the difference between measurements is approximately 6 mm, the threads are cross-threaded by one row (6 mm), so remove and reinstall the fuel pump gauge retainer.




i.
A307860C01
1.583,1.656 1.688,1.979 true 1.344,2.938 1.552,2.5 true 2.292,1.042 2.573,0.771 false 2.594,0.656 2.906,0.813 0.313,0.156 10 false *a 1.635,1.99 1.948,2.146 0.313,0.156 10 false *b 1.625,2.375 1.938,2.531 0.313,0.156 10 false *c 1.271,0.656 1.583,0.813 0.313,0.156 10 false *d 0.438,0.875 0.75,1.031 0.313,0.156 10 false *e 0.385,2.958 0.635,3.146 0.25,0.188 10 false *f 2.802,1.125 3.115,1.281 0.313,0.156 10 false *e 1.865,0.792 2.177,0.948 0.313,0.156 10 false *d
*a SST (Handle)
*b SST (Plate)
*c Fuel Pump Gauge Retainer Start of Threads Location
*d Worker A
*e Worker B
*f Approximately 90°
V100135

Press Down
V100136

Slowly Rotate
V100137

Front Side of Vehicle


Install SST (handle) to SST (plate).

SST
09808-14030  (09808-01010, 09808-01020, 09808-01030, 09808-01040, 09808-01050)


j.

While one person presses down to prevent the fuel pump gauge retainer and fuel suction tube with pump and gauge assembly from rotating together, the other person should slowly rotate SST (handle) and tighten the fuel pump gauge retainer by approximately 90°.

CAUTION:

Make sure not to pinch your hands with SST.



k.
A307861C01
1.99,1.531 2.563,1.604 true 2.292,3.521 2.583,2.625 true 1.396,1.24 1.073,1.354 false 2.625,1.51 2.938,1.667 0.313,0.156 10 false *a 0.906,1.271 1.219,1.427 0.313,0.156 10 false *b 2.625,2.5 2.938,2.656 0.313,0.156 10 false *c 1.771,0.917 1.969,1.115 0.198,0.198 10 true *d 1.885,1.833 2.125,2.042 0.24,0.208 10 false *e 2.885,3.344 3.198,3.573 0.313,0.229 10 false *f 1.677,0.323 1.99,0.479 0.313,0.156 10 false *d
*a SST (Handle)
*b SST (Plate)
*c Fuel Pump Gauge Retainer Start of Threads Location
*d Worker A
*e Worker B
*f Fully Tightened Position
V100135

Hold Down
V100136

Slowly Rotate
V100137

Front Side of Vehicle


To make sure SST does not separate from the fuel pump gauge retainer, one person should hold down the center of SST from above while at the same time both people slowly rotate SST (handle), and slowly tighten the fuel pump gauge retainer until it reaches the fully tightened position.


Hide 77209F 4.CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.

Connect the fuel tank main tube sub-assembly to the fuel suction tube with pump and gauge assembly.


b.
A307867C01
1.167,2.427 0.969,2.708 false 1.125,2.333 0.875,2.24 false 1.302,2.031 1.115,1.969 false 1.5,1.396 0.885,1.271 true 2.385,2.292 2.146,2.188 false 1.094,3.365 0.885,3.51 false 2.521,3.292 2.333,3.51 false 2.531,3.51 2.365,3.719 true 2.833,3.781 2.594,3.781 true 1.333,3.698 1.125,3.698 true 1.104,4.167 0.938,3.823 true 1.385,3.635 1.698,3.792 0.313,0.156 10 false *1 1.198,3.271 1.51,3.427 0.313,0.156 10 false *2 2.448,2.229 2.76,2.385 0.313,0.156 10 false *3 0.781,2.646 1.094,2.802 0.313,0.156 10 false *4 0.417,3.167 0.729,3.323 0.313,0.156 10 false *a 1.885,3.135 2.198,3.292 0.313,0.156 10 false *b 1.146,4.156 1.458,4.313 0.313,0.156 10 false *c 2.552,3.427 2.865,3.583 0.313,0.156 10 false *c 2.865,3.708 3.177,3.865 0.313,0.156 10 false *1 2.573,3.229 2.885,3.385 0.313,0.156 10 false *2 0.698,2.156 1.01,2.313 0.313,0.156 10 false *1 0.958,1.875 1.271,2.031 0.313,0.156 10 false *2 0.708,1.177 1.021,1.333 0.313,0.156 10 false *1
*1 Tube Joint Clip
*2 Fuel Tube Joint
*3 Nylon Tube
*4 Fuel Suction Plate
*a Correct
*b Incorrect
*c Rib


Install the tube joint clip.

NOTICE:
·

Make sure there is no damage to or foreign matter on the connecting surfaces.

·

Check that the fuel tube joint is correctly and fully inserted.

·

Check that the tube joint clip is above the rib of the fuel tube joint.

·

After installing the tube joint clip, make sure the fuel tube joint is secure.

·

Do not damage any of the clips. If a tube joint clip is damaged, replace it.




Hide 5. CHECK AIRTIGHTNESS

a.
A307868C01
0.729,0.708 0.427,0.417 false 2.135,1.333 1.708,1.208 true 0.25,0.313 0.563,0.469 0.313,0.156 10 false *a 1.531,1.125 1.844,1.281 0.313,0.156 10 false *b
*a Vacuum Pump
*b Port B


Install a vacuum pump to port B of the fuel suction tube with pump and gauge assembly as shown in the illustration.


b.
A307863C01
1.021,0 1.76,0 false
V100145

Apply Soapy Water Here


Apply soapy water to the contact areas between the fuel suction tube with pump and gauge assembly and the fuel pump gauge retainer.

NOTICE:

Cover the connecters of the fuel suction tube with pump and gauge assembly with protective tape.



c.
A307866C01
2.396,0.938 2.677,0.448 true 2.188,1.333 1.76,1.521 true 0.76,0.719 0.469,0.458 false 2.698,0.354 3.01,0.51 0.313,0.156 10 false *a 1.552,1.448 1.865,1.604 0.313,0.156 10 false *b 0.281,0.365 0.594,0.521 0.313,0.156 10 false *c
*a Port A
*b Port B
*c Vacuum Pump


Close port A and use the vacuum pump to apply 5 kPa (0.1 kgf/cm2, 1 psi) of compressed air to port B as shown in the illustration.

NOTICE:

Do not apply more compressed air than necessary.



d.

Check that the contact areas between the fuel suction tube with pump and gauge assembly and fuel pump gauge retainer are airtight.

NOTICE:
·

If air bubbles appear, remove and reinstall the fuel pump gauge retainer.

·

After a fuel pump gauge retainer and fuel suction tube set gasket have been used once, replace them with new parts.

·

When removing and reinstalling the fuel pump gauge retainer, make sure to clean away the soapy water to prevent the fuel suction tube set gasket from slipping out of position and being assembled incorrectly.



HINT:
A307865C01
2.188,1.104 2.75,0.656 true 2.76,0.552 3.073,0.708 0.313,0.156 10 false *a
*a Air Bubbles


If the assembled components are not airtight due to improper installation of the fuel pump gauge retainer, etc., air bubbles will appear as shown in the illustration.



Hide 77701W 6.CONNECT NO. 1 CANISTER OUTLET HOSE SUB-ASSEMBLY

a.

Connect the No. 1 canister outlet hose sub-assembly to the fuel suction tube with pump and gauge assembly.


Hide 77028F 7.CONNECT NO. 2 FUEL EMISSION TUBE SUB-ASSEMBLY

a.

Connect the No. 2 fuel emission tube sub-assembly to the fuel suction tube with pump and gauge assembly with the hose clip.


Hide 58325E 9.INSTALL REAR FLOOR SERVICE HOLE COVER

a.

Fully remove any butyl tape remaining on the rear floor service hole cover and vehicle floor.


b.
A305614C01
0,0 0,0 false
V100145

Butyl Tape


Apply new butyl tape to the rear floor service hole cover as shown in the illustration.


c.

Connect the fuel suction tube with pump and gauge assembly connector.


d.
A307875C01
1.333,0.552 1.094,0.354 true 2.771,1.688 3.021,1.854 true 0.906,0.25 1.167,0.469 0.26,0.219 10 true *a 3.094,1.781 3.354,2 0.26,0.219 10 true *a
*a Alignment Mark


Align the 2 alignment marks, and install the rear floor service hole cover to the vehicle floor.


e.
A307877C01
0.792,1.938 1.542,1.823 true 1.979,1.781 2.177,1.646 false 0.604,1.865 0.917,2.021 0.313,0.156 10 false *1 2.219,1.542 2.531,1.698 0.313,0.156 10 false *a
*1 Fuel Suction Tube with Pump and Gauge Assembly Wire
*a Bead of the Vehicle Floor


Install a new No. 8 wiring harness protector to the rear floor service hole cover and vehicle floor.

NOTICE:

Make sure the fuel suction tube with pump and gauge assembly wire is not on top of the bead of the vehicle floor.



Hide 73707 10.INSTALL CHILD RESTRAINT SEAT ANCHOR INNER BRACKET SUB-ASSEMBLY