35149B
1.INSTALL TRANSAXLE CASE 2ND BRAKE GASKET
Apply a light coat of Toyota Genuine ATF WS to a new transaxle case 2nd brake gasket and install it to the automatic transaxle case sub-assembly.
35145C
2.INSTALL TRANSAXLE CASE GASKET
Apply a light coat of Toyota Genuine ATF WS to a new transaxle case gasket and install it to the automatic transaxle case sub-assembly.
35251
3.INSTALL CHECK BALL BODY
Install the check ball body compression spring and check ball body to the automatic transaxle case sub-assembly.
35410
4.INSTALL TRANSMISSION VALVE BODY ASSEMBLY
| *1 | Manual Valve |
| *2 | Manual Valve Lever Sub-assembly |
Align the groove of the manual valve with the pin of the manual valve lever sub-assembly.
Temporarily install the transmission valve body assembly to the automatic transaxle case sub-assembly with the 13 bolts.
Bolt length:
Bolt A: 20 mm (0.787 in.)
Bolt B: 32 mm (1.26 in.)
Bolt C: 45 mm (1.77 in.)
Bolt D: 55 mm (2.17 in.)
| *1 | Manual Detent Spring Sub-assembly |
| *2 | Manual Detent Spring Cover |
Temporarily install the manual detent spring sub-assembly and manual detent spring cover to the transmission valve body assembly with the 2 bolts.
Bolt length:
Bolt A: 14 mm (0.551 in.)
Bolt B: 45 mm (1.77 in.)
Check that the manual valve lever sub-assembly comes into contact with the center of the roller at the tip of the manual detent spring sub-assembly.
Tighten the 15 bolts.
82125J
5.CONNECT TRANSMISSION WIRE
Connect the 5 connectors to the transmission valve body assembly.
Apply a light coat of Toyota Genuine ATF WS to the ATF temperature sensor O-ring on the transmission wire.
Install the transmission wire to the transmission valve body assembly with the temperature sensor clamp and bolt.
Bolt length: 55 mm (2.17 in.)
35330
6.INSTALL VALVE BODY OIL STRAINER ASSEMBLY
Apply a light coat of Toyota Genuine ATF WS to a new oil strainer O-ring and install it to the valve body oil strainer assembly.
Install the valve body oil strainer assembly to the transmission valve body assembly with the 3 bolts.
35394
7.INSTALL TRANSMISSION OIL CLEANER MAGNET
Install the 2 transmission oil cleaner magnets to the automatic transaxle oil pan sub-assembly as shown in the illustration.
35106D
8.INSTALL AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY
Clean and degrease the 2 bolts A and bolt holes.
| *a | Adhesive |
Apply adhesive to 2 or 3 threads on the ends of the 2 bolts A.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
To prevent contamination by foreign matter, install immediately after applying adhesive.
Install a new automatic transaxle oil pan gasket and automatic transaxle oil pan sub-assembly to the automatic transaxle case sub-assembly with the 19 bolts.
Completely remove any oil or grease from the contact surfaces of the automatic transaxle case sub-assembly and the automatic transaxle oil pan sub-assembly with the automatic transaxle oil pan gasket before installation.
9.ADD AUTOMATIC TRANSAXLE FLUID
Pull out the transmission oil level dipstick sub-assembly from the transmission oil filler tube sub-assembly.
Add Toyota Genuine ATF WS through the transmission oil filler tube sub-assembly.
| Classification | Capacity
(Reference) |
|
|---|---|---|
| Toyota Genuine ATF WS | Dry fill | 6.4 liters (6.8 US qts, 5.6 Imp. qts) |
| Drain and refill | 2.5 liters (2.6 US qts, 2.2 Imp. qts) | |
10.INSPECT AUTOMATIC TRANSAXLE FLUID
11.INSPECT FOR AUTOMATIC TRANSAXLE FLUID LEAK
51442C
12.INSTALL ENGINE UNDER COVER LH (w/o Metal Type Under Cover)
51405A
13.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (w/ Metal Type Under Cover)
51451A
14.INSTALL CENTER ENGINE UNDER COVER (w/ Metal Type Under Cover)