Home › Drivetrain › U340E AUTOMATIC TRANSMISSION / TRANSAXLE › DIFFERENTIAL OIL SEAL › 2013.08–2016.10
RM30M0E _52 Drivetrain _017087 U340E AUTOMATIC TRANSMISSION / TRANSAXLE _0090612 DIFFERENTIAL OIL SEAL A

U340E AUTOMATIC TRANSMISSION / TRANSAXLE  DIFFERENTIAL OIL SEAL  REPLACEMENT  


PROCEDURE

Hide 1.REMOVE FRONT DRIVE SHAFT ASSEMBLIES

Hide 43420H 2.REMOVE FRONT DRIVE SHAFT OIL SEAL LH

a.
C282047E01
2.083,2.406 2.177,1.854 true 1.948,2.417 2.406,2.615 0.458,0.198 10 false SST

Using SST, remove the front drive shaft oil seal LH from the automatic transaxle assembly.

SST
09308-00010  

NOTICE:

Do not damage the front drive shaft oil seal LH contact surface of the automatic transaxle assembly.



Hide 43410M 3.REMOVE FRONT DRIVE SHAFT OIL SEAL RH

a.
C282046E01
2.24,0.865 2.792,0.313 true 2.833,0.208 3.365,0.458 0.531,0.25 10 true SST

Using SST, remove the front drive shaft oil seal RH from the automatic transaxle assembly.

SST
09308-00010  

NOTICE:

Do not damage the front drive shaft oil seal RH contact surface of the automatic transaxle assembly.



Hide 43420H 4.INSTALL FRONT DRIVE SHAFT OIL SEAL LH

a.
C282049C01
2.177,1.406 1.938,2.385 1.938,2.385 1.615,1.146 true 1.25,2.354 1.292,1.99 1.292,1.99 1.031,2.115 false 1.229,3.083 1.542,3.24 0.313,0.156 10 false *a 1.813,2.396 2.271,2.594 0.458,0.198 10 false SST 1.333,1.885 1.792,2.083 0.458,0.198 10 false SST
*a Drive in Depth


Using SST and a hammer, tap in a new front drive shaft oil seal LH to the automatic transaxle assembly.

SST
09710-20011  (09710-06071)
09950-70010  (09951-07200)

Standard depth:

5.4 to 6.4 mm (0.213 to 0.251 in.)


NOTICE:
·

Be sure to install the front drive shaft oil seal LH in the correct direction.

·

Make sure to install the front drive shaft oil seal LH as specified, otherwise malfunctions such as a fluid leak will occur.




b.

Apply MP grease to the lip of the front drive shaft oil seal LH.


Hide 43410M 5.INSTALL FRONT DRIVE SHAFT OIL SEAL RH

a.
C282048C01
1.927,0.698 2.688,0.313 true 0.906,0.594 2.688,0.313 2.688,0.313 2.208,0.792 true 1.375,2.271 1.167,2.083 false 1.823,2.26 1.146,2.073 1.146,2.073 1.208,2.427 false 1.76,3.104 2.073,3.26 0.313,0.156 10 false *a 2.729,0.208 3.188,0.406 0.458,0.198 10 false SST 0.844,2 1.302,2.198 0.458,0.198 10 false SST
*a Drive in Depth


Using SST and a hammer, tap in a new front drive shaft oil seal RH to the automatic transaxle assembly.

SST
09630-24014  (09620-24051)
09950-60010  (09951-00410, 09951-00530, 09952-06010)
09950-70010  (09951-07100)

Standard depth:

1.5 to 2.5 mm (0.0591 to 0.0984 in.)


NOTICE:
·

Be sure to install the front drive shaft oil seal RH in the correct direction.

·

Make sure to install the front drive shaft oil seal RH as specified, otherwise malfunctions such as a fluid leak will occur.




b.

Apply MP grease to the lip of the front drive shaft oil seal RH.