Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY › 2013.08–2016.04
RM30M0E _52 Drivetrain _017092 DRIVE SHAFT / PROPELLER SHAFT _0092752 FRONT DRIVE SHAFT ASSEMBLY A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 43420G 1.INSTALL FRONT DRIVE SHAFT HOLE SNAP RING

a.

Install a new front drive shaft hole snap ring to the front drive shaft assembly.


Hide 43420 2.INSTALL FRONT DRIVE SHAFT ASSEMBLY LH

a.

for U340E Automatic Transaxle

i.

Coat the splines of the front drive inboard joint assembly with Toyota Genuine ATF WS.



b.

for U441E Automatic Transaxle

i.

Coat the splines of the front drive inboard joint assembly with Toyota Genuine ATF Type T-IV.



c.

for Manual Transaxle

i.

Coat the splines of the front drive inboard joint assembly with gear oil.



d.

Coat the lip of the front drive shaft oil seal LH with MP grease.


e.
C287117

Align the inboard joint splines, and using a brass bar and a hammer, install the front drive shaft assembly LH.

NOTICE:
·

Face the end gap of the front drive shaft hole snap ring downward.

·

Do not damage the front drive shaft oil seal LH.

·

Do not damage the front axle inboard joint boot.

·

Make sure to center the front drive shaft assembly LH during installation to prevent damage to the front drive shaft hole snap ring.



HINT:

Confirm whether the front drive shaft assembly LH is securely driven in by checking the reaction force and sound.



Hide 43410 3.INSTALL FRONT DRIVE SHAFT ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 4.INSTALL FRONT AXLE ASSEMBLY

a.
C283835C01
2.771,1.021 3.094,0.729 3.094,0.729 2.927,1.313 true 3.125,0.615 3.365,0.844 0.24,0.229 10 false *a
*a Matchmark


Align the matchmarks and install the front axle assembly to the front drive shaft assembly LH.

NOTICE:

Be careful not to damage the front axle outboard joint boot.



Hide 48069 5.INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY

Hide 45047 7.INSTALL TIE ROD END SUB-ASSEMBLY

Hide 47313A 8.INSTALL FRONT FLEXIBLE HOSE (w/ ABS)

a.
C283834E01
1.438,0.24 1.594,0.438 0.156,0.198 10 false A 1.823,1.052 1.969,1.219 0.146,0.167 10 true B

Install the front speed sensor wire and front flexible hose to the front shock absorber assembly and body with the 2 bolts.

Torque:
Bolt A : 8.5 N*m (87 kgf*cm, 75 in.*lbf)
Bolt B : 30.4 N*m (310 kgf*cm, 22 ft.*lbf)

NOTICE:

Install the front speed sensor wire and front flexible hose without twisting them.


HINT:

Install the front speed sensor wire first and then the front flexible hose.



Hide 47313A 9.INSTALL FRONT FLEXIBLE HOSE (w/o ABS)

a.

Install the front flexible hose to the front shock absorber assembly with the bolt.

Torque:
30.4 N*m (310 kgf*cm, 22 ft.*lbf)

NOTICE:

Install the front flexible hose without twisting it.



Hide 43502H 10.INSTALL FRONT AXLE SHAFT NUT

a.

Clean the threaded parts on the front drive shaft assembly and a new front axle shaft nut using non-residue solvent.

NOTICE:
·

Be sure to perform this work even when using a new front drive shaft assembly.

·

Keep the threaded parts free of oil and foreign matter.




b.
C283837

Using a 30 mm deep socket wrench, install the front axle shaft nut.

Torque:
216 N*m (2203 kgf*cm, 159 ft.*lbf)

HINT:

Keep depressing the brake pedal to prevent the front drive shaft assembly from rotating.



c.

Using a chisel and a hammer, stake the front axle shaft nut.


Hide 15.INSPECT FOR AUTOMATIC TRANSAXLE FLUID LEAK (for Automatic Transaxle)

Hide 16.INSPECT FOR MANUAL TRANSAXLE OIL LEAK (for Manual Transaxle)

Hide 51441C 17.INSTALL ENGINE UNDER COVER RH (w/o Metal Type Under Cover)

Hide 51442C 18.INSTALL ENGINE UNDER COVER LH (w/o Metal Type Under Cover)

Hide 51405A 19.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (w/ Metal Type Under Cover)

Hide 51451A 20.INSTALL CENTER ENGINE UNDER COVER (w/ Metal Type Under Cover)

Hide 21.INSTALL FRONT WHEELS

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)