Home › Drivetrain › U340E AUTOMATIC TRANSMISSION / TRANSAXLE › TORQUE CONVERTER AND DRIVE PLATE › 2013.08–2016.10
RM30M0E _52 Drivetrain _017087 U340E AUTOMATIC TRANSMISSION / TRANSAXLE _0090615 TORQUE CONVERTER AND DRIVE PLATE G

U340E AUTOMATIC TRANSMISSION / TRANSAXLE  TORQUE CONVERTER AND DRIVE PLATE  INSPECTION  


PROCEDURE

Hide 1.INSPECT TORQUE CONVERTER ASSEMBLY

a.

Inspect the one-way clutch.

i.
C286127N01
1.458,0.448 1.948,0.365 1.948,0.365 1.625,0.625 false 1.99,0.26 2.448,0.458 0.458,0.198 10 false SST

Set SST into the inner race of the one-way clutch.

SST
09350-32014  (09351-32010)


ii.

Install SST so that it fits in the notch of the torque converter assembly hub and the outer race of the one-way clutch.

SST
09350-32014  (09351-32020)


iii.
C286128C01
1.792,0.365 2.104,0.521 0.313,0.156 10 false *a 1.958,1.656 2.271,1.813 0.313,0.156 10 false *b
*a Hold
*b Turn
V100135

Lock
V100136

Smooth


Stand the torque converter assembly up and turn SST.

Standard:

The inner race of the one-way clutch rotates smoothly when turned clockwise and locks when turned counterclockwise.




b.
C197457C08
0.083,0 0.5,0.385 0.417,0.385 10 *a 1.677,3.26 1.865,3.417 0.188,0.156 10 *b
*a Sample showing maximum allowable amount of powder in ATF
*b Full Scale


Inspect the torque converter assembly.

If any of the following problems are present, replace the torque converter assembly.

Malfunction:
·

A metallic sound is emitted from the torque converter assembly during the stall test or when the shift lever is moved to N.

·

The one-way clutch turns smoothly or locks in both directions.

·

The amount of powder in the ATF is more than the sample shown in the illustration (refer to the sample).


HINT:

The sample shows approximately 0.025 liters (0.026 US qts, 0.022 Imp. qts) of ATF in a Petri dish, which has been taken from the removed torque converter assembly.



c.

Replace the ATF in the torque converter assembly.

HINT:

If the ATF is discolored or has a foul odor, stir the ATF in the torque converter assembly and drain it before replacing the ATF.



d.
C282854

Clean and check the oil cooler and oil pipe line.

HINT:
·

If the torque converter assembly is inspected or the fluid is replaced, it is necessary to clean the oil cooler and oil pipe line.

·

Apply compressed air of 196 kPa (2.0 kgf/cm2, 28 psi) into the inlet hose.

·

If a large amount of powder is found in the fluid, add new fluid using a bucket pump and clean the oil cooler and oil pipe line again.

·

If the fluid is cloudy, inspect the oil cooler.




e.
C282855C01
2.458,1.667 2.927,1.667 true 0.375,0.198 0.688,0.396 0.313,0.198 10 false *a 1.74,0.198 2.052,0.396 0.313,0.198 10 false *b 2.969,1.573 3.281,1.771 0.313,0.198 10 false *c
*a Correct
*b Incorrect
*c Bottom is damaged


Prevent deformation of the torque converter assembly and damage to the oil pump gear.

NOTICE:

Make sure that all of the bolts are the same length and that the specified bolts are used.


HINT:

If there is any damage to the tip of a bolt for the torque converter assembly or to the bottom of a bolt hole, replace the bolt and the torque converter assembly.



Hide 2.INSPECT DRIVE PLATE

a.

Check the drive plate for damage.


b.
C233998C02
1.615,0.573 1.771,0.771 0.156,0.198 10 false 1 2.073,0.156 2.229,0.354 0.156,0.198 10 false 2 2.781,0.635 2.938,0.833 0.156,0.198 10 false 3 3.01,1.521 3.167,1.719 0.156,0.198 10 false 4 2.563,1.958 2.719,2.156 0.156,0.198 10 false 5 1.844,1.479 2,1.677 0.156,0.198 10 false 6
V100144

Measurement Point


Set up a dial indicator and measure the runout at the 6 areas on the drive plate surface that contact the torque converter assembly.

Maximum runout:

0.30 mm (0.0118 in.)


If the runout is more than the maximum or the drive plate is damaged, replace the drive plate.

Click hereEngine / Hybrid System>1NZ-FE ENGINE MECHANICAL>REAR CRANKSHAFT OIL SEAL>INSTALLATION