Home › Engine / Hybrid System › 1NZ-FE ENGINE MECHANICAL › REAR CRANKSHAFT OIL SEAL › 2013.08–2016.07
RM30M0E _51 Engine / Hybrid System _017073 1NZ-FE ENGINE MECHANICAL _0091004 REAR CRANKSHAFT OIL SEAL A

1NZ-FE ENGINE MECHANICAL  REAR CRANKSHAFT OIL SEAL  INSTALLATION  


PROCEDURE

Hide 11401L 1.INSTALL REAR ENGINE OIL SEAL

a.

Apply MP grease to the lip of a new rear engine oil seal.

NOTICE:

Keep the lip free of foreign matter.



b.
A166929E04
2.896,1.76 2.688,1.604 false 1.125,2.719 1.24,2.448 false 2.729,1.802 3.021,1.948 0.292,0.146 10 false SST 1.115,2.01 2.073,2.198 0.958,0.188 10 false 0 to -1.0 mm 1.281,2.354 1.74,2.552 0.458,0.198 10 false SST

Using SST and hammer, tap in the rear engine oil seal until its surface is flush with the cylinder block sub-assembly and oil pan sub-assembly.

SST
09223-56010  

Rear engine oil seal tap in depth:

0 to -1.0 mm (0 to -0.04 in.)


NOTICE:
·

Do not tap the oil pump seal at an angle.

·

Wipe off extra grease from the crankshaft.




Hide 32101B 2.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transaxle)

a.
A166739E01
2.63,1.619 2.935,1.773 0.304,0.155 10 SST 1.954,2.054 2.592,1.726 false

Using SST, hold the crankshaft damper sub-assembly.

SST
09960-10010  (09962-01000, 09963-01000)


b.
A248257C03
1.094,1.719 1.26,1.396 false 2.083,1.854 1.771,1.854 false 2.24,1.083 2.625,1.448 false 0.927,1.667 1.094,1.833 0.167,0.167 10 *1 2.115,1.792 2.281,1.958 0.167,0.167 10 *2 2.646,1.427 2.813,1.594 0.167,0.167 10 *3
*1 Front Drive Plate Spacer (Reversible)
*2 Drive Plate and Ring Gear Sub-assembly
*3 Rear Drive Plate Spacer
V100135

Engine Side
V100136

Transaxle Side


Install the front drive plate spacer, drive plate and ring gear sub-assembly, and rear drive plate spacer to the crankshaft.

NOTICE:

As the drive plate and ring gear sub-assembly and rear drive plate spacer are not reversible, be sure to install them so that they are facing in the direction shown in the illustration.


HINT:

The front drive plate spacer is reversible.



c.

Clean the 6 bolts and their holes.


d.
A192239C40
1.781,0.552 1.542,1.385 false 1.823,0.458 2,0.615 0.177,0.156 10 false *a
*a Adhesive


Apply adhesive to 2 or 3 threads at the end of each of the 6 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

To prevent contamination by foreign matter, install immediately after applying adhesive.



e.
A158035E06
1.823,0.542 1.927,0.698 0.104,0.156 10 1 1.833,1.51 1.948,1.677 0.115,0.167 10 2 2.229,0.781 2.385,0.958 0.156,0.177 10 3 1.417,1.271 1.573,1.427 0.156,0.156 10 4 2.24,1.292 2.406,1.458 0.167,0.167 10 5 1.385,0.792 1.552,0.969 0.167,0.177 10 6

Install and uniformly tighten the 6 bolts in several steps, in the sequence shown in the illustration.

Torque:
88 N*m (897 kgf*cm, 65 ft.*lbf)

NOTICE:

Do not start the engine for at least 1 hour after installing the drive plate and ring gear sub-assembly.



Hide 13405 3.INSTALL FLYWHEEL SUB-ASSEMBLY (for Manual Transaxle)

a.
A166739E02
2.63,1.619 2.935,1.773 0.304,0.155 10 SST 1.954,2.054 2.592,1.726 false

Using SST, hold the crankshaft damper sub-assembly.

SST
09960-10010  (09962-01000, 09963-01000)


b.

Install the flywheel sub-assembly to the crankshaft.


c.

Clean the 6 bolts and their holes.


d.
A192239C41
1.781,0.552 1.542,1.385 false 1.833,0.458 2.01,0.615 0.177,0.156 10 false *a
*a Adhesive


Apply adhesive to 2 or 3 threads at the end of each of the 6 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

To prevent contamination by foreign matter, install immediately after applying adhesive.



e.
A278689E01
1.823,0.5 1.979,0.698 0.156,0.198 10 1 2.281,0.781 2.438,0.979 0.156,0.198 10 3 2.281,1.313 2.438,1.51 0.156,0.198 10 5 1.833,1.573 1.99,1.771 0.156,0.198 10 2 1.375,1.313 1.531,1.51 0.156,0.198 10 4 1.365,0.792 1.521,0.99 0.156,0.198 10 6

Install and uniformly tighten the 6 bolts in several steps, in the sequence shown in the illustration.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)


f.
A278690C02
1.385,0.865 1.74,1.135 false 1.188,0.75 1.5,0.906 0.313,0.156 10 false *a 2.24,0.729 2.552,0.885 0.313,0.156 10 false 90°
*a Paint Mark
V100136

Engine Upper Side


Mark paint marks on the bolt heads on the engine upper side.


g.

Tighten the bolts 90° in the sequence shown in the illustration.

NOTICE:

Do not start the engine for at least 1 hour after installing the flywheel sub-assembly.



Hide 31250B 4.INSTALL CLUTCH DISC ASSEMBLY (for Manual Transaxle)

Hide 31210 5.INSTALL CLUTCH COVER ASSEMBLY (for Manual Transaxle)

Hide 31210 6.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY (for Manual Transaxle)

Hide 30300 7.INSTALL MANUAL TRANSAXLE ASSEMBLY (for Manual Transaxle)

Hide 8.INSTALL AUTOMATIC TRANSAXLE ASSEMBLY (for Automatic Transaxle)