Home › Drivetrain › U441E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM › 2013.08–2016.10
RM30M0E _52 Drivetrain _017088 U441E AUTOMATIC TRANSMISSION / TRANSAXLE _0090618 AUTOMATIC TRANSAXLE SYSTEM D

U441E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  DIAGNOSIS SYSTEM  


M-OBD (EXCEPT EUROPEAN SPEC.)


a.

When troubleshooting Multiplex On-Board Diagnostic (M-OBD) vehicles, the vehicle must be connected to the GTS. Various data output from the ECM can then be read.


b.
C234359

OBD regulations require that the vehicle's on-board computer illuminate the MIL on the instrument panel when the computer detects a malfunction in any of the following:

·

The emission control system/components

·

The power train control components (which affect vehicle emissions)

·

The computer


In addition, the applicable Diagnostic Trouble Codes (DTCs) prescribed by ISO 15765-4 are recorded in the ECM memory.

If the malfunction does not recur in 3 consecutive trips, the MIL goes off automatically but the DTCs remain recorded in the ECM memory.



NORMAL MODE AND CHECK MODE


The diagnosis system operates in normal mode during normal vehicle use. In normal mode, 2 trip detection logic is used to ensure accurate detection of malfunctions. Check mode is also available to technicians as an option. In check mode, 1-trip detection logic is used for simulating malfunction symptoms and increasing the system's ability to detect malfunctions, including intermittent malfunctions (GTS only).


2 TRIP DETECTION LOGIC


a.

When a malfunction is first detected, the malfunction is temporarily stored in the ECM memory (1st trip). If the ignition switch is turned off and then turned on again, and the same malfunction is detected again, the MIL illuminates.



FREEZE FRAME DATA


a.

The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not and whether the air/fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.


b.
C140837E36
0.354,1.74 2.792,1.99 2.438,0.25 10 false Freeze frame data which can be read 0.875,0.708 1.167,0.875 0.292,0.167 10 false 0.5 1.531,0.708 2.156,0.906 0.625,0.198 10 false 0.5 2.135,0.708 2.417,0.896 0.281,0.188 10 false 0.5 1.823,0.104 2.875,0.396 1.052,0.292 10 false DTC was set 0.135,0.427 0.844,0.635 0.708,0.208 10 false (Seconds)

The GTS displays freeze frame data recorded at five different points: 1) 3 times before the DTC is set, 2) once when the DTC is set, and 3) once after the DTC is set. The data can be used to simulate the vehicle's condition around the time of the malfunction. The data may be helpful in determining the cause of a malfunction. It may also be helpful in determining whether a DTC is being caused by a temporary malfunction.



DLC3 (Data Link Connector 3)




CHECK BATTERY VOLTAGE


Standard battery voltage:

11 to 14 V


a.

If the voltage is below 11 V, replace the battery before proceeding.



CHECK MIL


a.

Check that the MIL illuminates when the ignition switch is turned to ON. If the MIL does not illuminate, there is a problem in the MIL circuit.

Click hereEngine / Hybrid System>1NZ-FE ENGINE CONTROL>SFI SYSTEM(for Automatic Transaxle)>MIL Circuit


b.

When the engine is started, the MIL goes off.