Home › Drivetrain › U441E AUTOMATIC TRANSMISSION / TRANSAXLE › DIFFERENTIAL CASE › 2013.08–2016.10
RM30M0E _52 Drivetrain _017088 U441E AUTOMATIC TRANSMISSION / TRANSAXLE _0090631 DIFFERENTIAL CASE A

U441E AUTOMATIC TRANSMISSION / TRANSAXLE  DIFFERENTIAL CASE  REASSEMBLY  


PROCEDURE

Hide 41039A 1.INSTALL DIFFERENTIAL GEAR KIT

a.
C286475

Coat the differential gear kit (2 front differential pinions and 2 front differential side gears), 2 front differential side gear thrust washers and the 2 front differential pinion thrust washers with Toyota Genuine ATF Type T-IV, and install them to the front differential case.

HINT:

Rotating each front differential side gear, install the 2 front differential pinions and the 2 front differential pinion thrust washers.



Hide 41342F 2.INSTALL FRONT NO. 1 DIFFERENTIAL PINION SHAFT

a.
C286472

Coat the front No. 1 differential pinion shaft with Toyota Genuine ATF Type T-IV.


b.

Install the front No. 1 differential pinion shaft so as to align the front differential pinion shaft straight pin holes in the front No. 1 differential pinion shaft and the front differential case.


Hide 3.INSPECT DIFFERENTIAL SIDE GEAR BACKLASH

Hide 41342A 4.INSTALL FRONT DIFFERENTIAL PINION SHAFT STRAIGHT PIN

a.
C286476

Using a 3 mm pin punch and a hammer, install the front differential pinion shaft straight pin to the front differential case.


b.
C286477

Using a chisel and a hammer, stake the front differential case hole.


Hide 41221 5.INSTALL FRONT DIFFERENTIAL RING GEAR

a.
C166738C01
1.063,0.417 1.281,0.615 0.219,0.198 10 false *a
*a 90 to 110°C (194 to 230°F)


Using Toyota Genuine ATF Type T-IV and a heater, heat the front differential ring gear to 90 to 110°C (194 to 230°F).

CAUTION:

Use thick gloves to protect your hands as the front differential ring gear is hot.


NOTICE:

Do not heat the ring gear to more than 110°C (230°F).



b.

Clean the contact surface of the front differential case and the front differential ring gear.


c.
C288072C01
1.573,1.615 2.302,1.906 2.302,1.906 1.604,1.5 true 2.344,1.823 2.656,1.979 0.313,0.156 10 false *a
*a Matchmark


After moisture on the front differential ring gear has completely evaporated, align the matchmarks on the front differential ring gear and the front differential case, and quickly install them.


d.
C286468

Secure the front differential case in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



e.

Install the 8 bolts.

Torque:
77.5 N*m (790 kgf*cm, 57 ft.*lbf)


Hide 41311F 6.INSTALL FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING

a.
C286927N01
1.042,0.458 1.552,0.677 false 0.75,0.375 1.208,0.573 0.458,0.198 10 false SST

Using SST and a press, install the front differential case rear tapered roller bearing (inner race) to the front differential case.

SST
09608-06041  


b.
C286480N01
1.531,0.927 2.156,1.302 2.156,1.302 1.604,1.406 true 2.208,1.229 2.667,1.427 0.458,0.198 10 false SST

Using SST and a hammer, install the front differential case rear plate washer and the front differential case rear tapered roller bearing (outer race) to the transaxle case.

SST
09950-60020  (09951-00710)
09950-70010  (09951-07100)


Hide 41311E 7.INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING

a.
C286926N01
1.083,0.406 1.552,0.604 false 0.792,0.323 1.25,0.521 0.458,0.198 10 false SST

Using SST and a press, install the front differential case front tapered roller bearing (inner race) to the front differential case.

SST
09608-06041  


b.
C286479N01
1.177,1.406 0.51,0.76 0.51,0.76 1.26,0.906 true 0.219,0.677 0.677,0.875 0.458,0.198 10 false SST

Using SST and a hammer, install the front differential case front tapered roller bearing (outer race) to the transaxle housing.

SST
09950-60020  (09951-00680)
09950-70010  (09951-07150)