Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM › 2013.08–2016.04
RM30M0E _58 Vehicle Interior _017112 LIGHTING (INT) _0090848 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  Engine Switch Illumination Circuit  


DESCRIPTION

The illuminated entry system controls the engine switch illumination.

WIRING DIAGRAM

E212454C03
2.969,1.177 3.396,1.354 0.427,0.177 10 false AGND 4.74,1.271 5.167,1.448 0.427,0.177 10 false AGND 3.031,0.781 3.771,1.156 0.74,0.375 10 false SWIL 4.74,0.875 5.51,1.198 0.771,0.323 10 false SWIL 4.479,1.177 4.656,1.354 0.177,0.177 10 false 24 4.49,0.781 4.667,0.958 0.177,0.177 10 false 19 3.469,1.177 3.563,1.354 0.094,0.177 10 false 6 3.469,0.781 3.563,0.958 0.094,0.177 10 false 9 1.875,1.729 2.188,1.906 0.313,0.177 10 false F13 1.885,1.875 3.583,2.229 1.698,0.354 10 false Engine Switch 4.333,1.688 4.667,1.865 0.333,0.177 10 false F43 4.323,1.854 6.135,2.188 1.813,0.333 10 false Certification ECU (Smart Key ECU Assembly)

CAUTION / NOTICE / HINT

NOTICE:

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (POWER/ENGINE SW LIGHT)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Entry&Start > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Power/Engine SW Light Engine switch illumination OFF or ON w/ Smart Entry and Start System
Body Electrical > Entry&Start > Active Test
Tester Display
Power/Engine SW Light
50004 125 27
OK:

Engine switch illumination comes on.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT ENGINE SWITCH
2.INSPECT ENGINE SWITCH


OK:

Engine switch illumination is normal.


Result:
Result Proceed to
OK A
NG (for 1NZ-FE) B
NG (for 2NZ-FE) C



A

3.CHECK HARNESS AND CONNECTOR (ENGINE SWITCH - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

B

C

3.CHECK HARNESS AND CONNECTOR (ENGINE SWITCH - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the F43 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the F13 engine switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F13-9 (SWIL) - F43-19 (SWIL) Always Below 1 Ω
F13-6 (AGND) - F43-24 (AGND) Always Below 1 Ω
F13-9 (SWIL) or F43-19 (SWIL) - Body ground Always 10 kΩ or higher
F13-6 (AGND) or F43-24 (AGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR