This DTC is stored when one of the following occurs: 1) the ECM detects errors in its own communications with the transponder key ECU assembly; 2) the ECM detects errors in the communication lines; or 3) the ECU - ECM communication ID between the transponder key ECU assembly and ECM is different and an engine start is attempted. Before troubleshooting for this DTC, make sure no engine immobiliser DTCs are output. If output, troubleshoot the engine immobiliser DTCs first.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
| B2799 | Engine Immobiliser System Malfunction | Either condition is met (1 trip detection logic*2):
·
A malfunction occurs in the communication or communication lines between the ECM and transponder key ECU assembly. ·
A communication code cannot be verified during communication between the ECM and transponder key ECU assembly. |
·
Wire harness or connector ·
Transponder key ECU assembly ·
ECM |
Either condition is met:
·
Within 10 seconds of an engine start operation being performed (with the clutch pedal depressed*1, turn the ignition switch to ON). If there is a malfunction, the engine stops (communication begins within 3 seconds of the engine start operation being performed, and DTCs are stored after 6 seconds). ·
10 seconds after the ignition switch is turned to ON after reconnecting the cable to the negative (-) battery terminal (communication begins within 3 seconds of the ignition switch being turned to ON, and DTCs are stored after 6 seconds). |
*1: for Manual Transaxle
*2: Only output while a malfunction is present.
| Vehicle Condition when Malfunction Detected | Fail-safe Operation when Malfunction Detected |
|---|---|
| Engine cannot be started | - |
| DTC No. | Data List and Active Test |
|---|---|
| B2799 | - |
If the transponder key ECU assembly or ECM is replaced, refer to Service Bulletin.
After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
If transponder key ECU assembly DTCs are output simultaneously, troubleshoot the transponder key ECU assembly DTCs first.
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Start the engine.
Check for DTCs.
Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.
B2799 is not output.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (DTC B2799 is output) | B |
| NG (Other DTCs are output) | C |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
Using an oscilloscope, check the waveform.
| *A | for Automatic Transaxle | *B | for Manual Transaxle |
| *a | Component with harness connected
(ECM) |
*b | Waveform |
| Item | Content |
|---|---|
| Tester Connection | F82-15 (IMO) - Body ground*1
F81-18 (IMO) - Body ground*2 |
| Tool Setting | 2 V/DIV., 500 ms./DIV. |
| Condition | Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal |
*1: for Automatic Transaxle
*2: for Manual Transaxle
Waveform is similar to that shown in the illustration.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Terminal IMO stuck low (2.4 V or less)) | B |
| NG (Terminal IMO stuck high (12 V) or abnormal waveform) | C |
A
B
C
Using an oscilloscope, check the waveform.
| *A | for Automatic Transaxle | *B | for Manual Transaxle |
| *a | Component with harness connected
(ECM) |
*b | Waveform |
| Item | Content |
|---|---|
| Tester Connection | F82-16 (IMI) - Body ground*1
F81-19 (IMI) - Body ground*2 |
| Tool Setting | 2 V/DIV., 500 ms./DIV. |
| Condition | Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal |
*1: for Automatic Transaxle
*2: for Manual Transaxle
Waveform is similar to that shown in the illustration.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reregister the ECU communication ID.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Using a registered key, turn the ignition switch to ON.
Check that the engine starts 5 seconds after the ignition switch was turned to ON.
Engine starts normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the ECM with a new one.
for 1NZ-FE: Click hereEngine / Hybrid System>1NZ-FE ENGINE CONTROL>ECM>REMOVAL
for 2NZ-FE: Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Reregister the ECU communication ID.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Using a registered key, turn the ignition switch to ON.
Check that the engine starts 5 seconds after the ignition switch was turned to ON.
Engine starts normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F82*1 or F81*2 ECM connector.
*1: for Automatic Transaxle
*2: for Manual Transaxle
Turn the ignition switch to ON.
| *A | for Automatic Transaxle |
| *B | for Manual Transaxle |
| *a | Front view of wire harness connector
(to ECM) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Result |
|---|---|---|
| F82-16 (IMI) - Body ground*1 | Ignition switch turned to ON using registered key | Terminal IMO stuck low (2.4 V or less) |
| Terminal IMO stuck high (12 V) or abnormal waveform | ||
| F81-19 (IMI) - Body ground*2 | Ignition switch turned to ON using registered key | Terminal IMO stuck low (2.4 V or less) |
| Terminal IMO stuck high (12 V) or abnormal waveform |
*1: for Automatic Transaxle
*2: for Manual Transaxle
| Result | Proceed to |
|---|---|
| Terminal IMI stuck low (2.4 V or less) | A |
| Terminal IMI stuck high (12 V) or Abnormal waveform | B |
A
B
Disconnect the F51 transponder key ECU assembly connector.
Disconnect the F82*1 or F81*2 ECM connector.
*1: for Automatic Transaxle
*2: for Manual Transaxle
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F51-5 (EFII) - F82-15 (IMO)*1 | Always | Below 1 Ω |
| F51-5 (EFII) - F81-18 (IMO)*2 | Always | Below 1 Ω |
| F51-5 (EFII) - Body ground | Always | 10 kΩ or higher |
| F82-15 (IMO) - Body ground*1 | Always | 10 kΩ or higher |
| F81-18 (IMO) - Body ground*2 | Always | 10 kΩ or higher |
*1: for Automatic Transaxle
*2: for Manual Transaxle
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the transponder key ECU assembly with a new one.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Register the key.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Register the ECU communication ID.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Using a registered key, turn the ignition switch to ON.
Check that the engine starts 5 seconds after the ignition switch was turned to ON.
Engine starts normally.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for 1NZ-FE) | B |
| NG (for 2NZ-FE) | C |
A
B
C