Home › Engine / Hybrid System › 2NZ-FE ENGINE CONTROL › SFI SYSTEM(for Automatic Transaxle) › 2013.08–2016.10
RM30M0E _51 Engine / Hybrid System _017072 2NZ-FE ENGINE CONTROL _0090867 SFI SYSTEM(for Automatic Transaxle) C

2NZ-FE ENGINE CONTROL  SFI SYSTEM(for Automatic Transaxle)  P0504  Brake Switch "A" / "B" Correlation  


DESCRIPTION

The stop light switch assembly is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If both signals, which indicate whether the brake pedal is being depressed or released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch assembly and stores the DTC.

HINT:

The normal signal conditions are as shown in the table below.

Signal (ECM Terminal) Brake Pedal Released In Transition Brake Pedal Depressed
STP OFF ON ON
ST1- ON ON OFF

·

[OFF] denotes ground potential.

·

[ON] denotes battery potential (+B).

·

On the GTS, both the Data List items Stop Light Switch and ST1 are ON when the brake pedal is depressed because the ST1 indication characteristic is opposite to the Stop Light Switch indication.



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0504 Brake Switch "A" / "B" Correlation Conditions (a) and (b) continue for 0.5 seconds or more
(1 trip detection logic):
(a) Ignition switch ON
(b) STP signal is off when ST1- signal is off
·

Open or short in stop light switch signal circuit

·

Stop light switch assembly

·

ECM


Does not come on DTC stored

WIRING DIAGRAM

A300990E01
6.156,0.552 6.771,0.75 0.615,0.198 10 false IGSW 6.156,1.073 6.771,1.271 0.615,0.198 10 false ST1- 6.156,1.688 6.771,1.885 0.615,0.198 10 false STP 6.146,2.323 6.76,2.521 0.615,0.198 10 false E1 5.844,0.563 6.219,0.76 0.375,0.198 10 false F83 5.844,1.083 6.219,1.281 0.375,0.198 10 false F83 5.833,1.698 6.208,1.896 0.375,0.198 10 false F83 5.833,2.313 6.208,2.51 0.375,0.198 10 false B29 5.906,0.385 6.063,0.583 0.156,0.198 10 false 9 5.875,0.865 6.135,1.052 0.26,0.188 10 false 16 5.875,1.5 6.135,1.688 0.26,0.188 10 false 15 5.906,2.115 6.104,2.302 0.198,0.188 10 false 1 3.813,2.229 6.031,2.573 2.219,0.344 10 false Stop Light Switch Assembly 3.823,2.063 4.198,2.26 0.375,0.198 10 false A21 0.74,0.875 1.115,1.073 0.375,0.198 10 false F7 0.74,1 2.667,1.417 1.927,0.417 10 false Ignition or Starter Switch Assembly*2 1.177,2.438 1.552,2.635 0.375,0.198 10 false F77 1.188,2.583 2.677,2.906 1.49,0.323 10 false No. 2 Ignition Relay*1 0.573,3.708 0.948,3.906 0.375,0.198 10 false F43 0.552,3.875 3.573,4.25 3.021,0.375 10 false Certification ECU (Smart Key ECU Assembly)*1 5.104,1.573 5.26,1.771 0.156,0.198 10 false 1 2.125,2.042 2.281,2.24 0.156,0.198 10 false 1 5.094,0.958 5.25,1.156 0.156,0.198 10 false 3 4.198,0.969 4.354,1.167 0.156,0.198 10 false 4 4.198,1.583 4.354,1.781 0.156,0.198 10 false 2 2.021,0.469 2.177,0.667 0.156,0.198 10 false 6 0.656,0.469 0.813,0.667 0.156,0.198 10 false 5 1.292,1.625 1.448,1.823 0.156,0.198 10 false 3 2.146,1.604 2.302,1.802 0.156,0.198 10 false 5 1.292,2.031 1.448,2.229 0.156,0.198 10 false 2 2.271,0.667 2.635,0.833 0.365,0.167 10 false *2 0.156,1.229 0.521,1.396 0.365,0.167 10 false *2 0.719,1.615 1.083,1.781 0.365,0.167 10 false *1 2.656,1.229 3.021,1.396 0.365,0.167 10 false *1 0.906,2.656 1.271,2.823 0.365,0.167 10 false *1 2.417,2.042 2.781,2.208 0.365,0.167 10 false *1 1.271,3.135 1.49,3.302 0.219,0.167 10 false 20 1.531,3.24 2.146,3.438 0.615,0.198 10 false IG1D 0.354,2.313 0.729,2.51 0.375,0.198 10 false AM2 0.375,3.333 0.75,3.531 0.375,0.198 10 false MAIN 0.583,5.073 1.156,5.271 0.573,0.198 10 false Battery 1.625,4.375 2,4.573 0.375,0.198 10 false ALT 3.677,2.823 4.198,3.073 0.521,0.25 10 false STOP 2.833,0.708 3.448,0.958 0.615,0.25 10 false IG2 NO.1 6.365,2.865 6.979,3.115 0.615,0.25 10 false ECM 4.281,4.281 6.635,4.635 2.354,0.354 10 false *1: w/ Smart Entry and Start System 4.281,4.74 6.635,5.094 2.354,0.354 10 false *2: w/o Smart Entry and Start System 0.844,0.469 1.24,0.656 0.396,0.188 10 false AM2 1.719,0.458 2.115,0.646 0.396,0.188 10 false IG2 4.365,0.969 4.521,1.167 0.156,0.198 10 false B 4.365,1.583 4.521,1.781 0.156,0.198 10 false B 4.938,0.969 5.094,1.167 0.156,0.198 10 false L 4.938,1.594 5.094,1.792 0.156,0.198 10 false L 0.385,4.5 0.958,4.719 0.573,0.219 10 false FL MAIN

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Stop light switch assembly conditions can be checked using the GTS.

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Enter the following menus: Powertrain / Engine and ECT / Data List / Stop Light Switch and ST1.

5.

Check the Data List indication when the brake pedal is depressed and released.

Brake Pedal Operation Stop Light Switch ST1
Depressed ON ON
Released OFF OFF




PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY)
a.
A148738C04
0.656,1.74 1.073,2.052 0.417,0.313 2.01,1.885 2.438,2.323 true 0.292,0.208 0.604,0.406 0.313,0.198 10 false *a 0.76,1.813 1.219,2.01 0.458,0.198 10 false A21 2.479,2.313 2.635,2.51 0.156,0.198 10 false B
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the stop light switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A21-2 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BATTERY)

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY)
a.
A148738C11
0.656,1.74 1.073,2.052 0.417,0.313 2.427,2.573 2.031,2.125 true 0.292,0.208 0.604,0.406 0.313,0.198 10 false *a 0.76,1.813 1.219,2.01 0.458,0.198 10 false A21 2.448,2.552 2.604,2.75 0.156,0.198 10 false B
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the stop light switch assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A21-4 (B) - Body ground Ignition switch ON 11 to 14 V



Result:
Result Proceed to
OK A
NG (w/ smart entry and start system) B
NG (w/o smart entry and start system) C



A

3.INSPECT STOP LIGHT SWITCH ASSEMBLY

B

5.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - NO. 2 IGNITION RELAY)

C

6.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - IGNITION OR STARTER SWITCH ASSEMBLY)
3.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK TERMINAL VOLTAGE (STP AND ST1- VOLTAGE)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

4.CHECK TERMINAL VOLTAGE (STP AND ST1- VOLTAGE)
a.

Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

A310007C03
4.344,0.802 4.76,1.052 0.417,0.25 6.354,1.427 5.958,0.938 true 5.406,1.51 5.823,0.938 true 1.031,1.438 1.229,1.646 0.198,0.208 10 false *a 2.74,1.427 2.958,1.625 0.219,0.198 10 false *b 4.708,0.135 4.938,0.333 0.229,0.198 10 false *c 5.25,1.531 5.583,1.74 0.333,0.208 10 false STP 6.26,1.458 6.635,1.667 0.375,0.208 10 false ST1- 4.427,0.844 4.729,1.031 0.302,0.188 10 false F83
*a Brake Pedal Depressed *b Brake Pedal Released
*c Front view of wire harness connector
(to ECM)
- -


Standard Voltage:
Tester Connection Condition Specified Condition
F83-16 (ST1-) - Body ground Brake pedal released 7.5 to 14 V
Brake pedal depressed Below 1.5 V
F83-15 (STP) - Body ground Brake pedal released Below 1.5 V
Brake pedal depressed 7.5 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)

5.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - NO. 2 IGNITION RELAY)
a.

Disconnect the A21 stop light switch assembly connector.


b.

Remove the No. 2 ignition relay.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A21-4 (B) - F77-5 (No. 2 ignition relay) Always Below 1 Ω
A21-4 (B) or F77-5 (No. 2 ignition relay) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - IGNITION OR STARTER SWITCH ASSEMBLY)
a.

Disconnect the A21 stop light switch assembly connector.


b.

Disconnect the F7 ignition or starter switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A21-4 (B) - F7-6 (IG2) Always Below 1 Ω
A21-4 (B) or F7-6 (IG2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR