Home › Engine / Hybrid System › 2NZ-FE ENGINE CONTROL › SFI SYSTEM(for Automatic Transaxle) › 2013.08–2016.10
RM30M0E _51 Engine / Hybrid System _017072 2NZ-FE ENGINE CONTROL _0090867 SFI SYSTEM(for Automatic Transaxle) C

2NZ-FE ENGINE CONTROL  SFI SYSTEM(for Automatic Transaxle)  P0617  Starter Relay Circuit High  


DESCRIPTION

While the engine is being cranked, the battery voltage is applied to terminal STA of the ECM.

If the ECM detects the starter signal (STA signal) while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.

This monitor runs when the vehicle is driven at 20 km/h (12.4 mph) for over 20 seconds.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0617 Starter Relay Circuit High Following conditions (a), (b) and (c) met for 20 seconds (1 trip detection logic):

(a) Vehicle speed 20 km/h (12.4 mph) or more

(b) Engine speed more than 1000 rpm

(c) STA signal ON


·

Park/neutral position switch

·

Starter relay circuit

·

Ignition or start switch assembly*1

·

Certification ECU (Smart key ECU assembly)*2

·

ECM


Comes on DTC stored

*1: w/o Smart Entry and Start System

*2: w/ Smart Entry and Start System


MONITOR DESCRIPTION

Required Sensors/Components (Main) Starter relay
Park/neutral position switch
Ignition or starter switch assembly*1
Certification ECU (Smart key ECU assembly)*2
Required Sensors/Components (Related) Vehicle speed sensor
Crankshaft position sensor
Frequency of Operation Continuous

*1: w/o Smart Entry and Start System

*2: w/ Smart Entry and Start System


TYPICAL ENABLING CONDITIONS

Vehicle speed 20 km/h (12.4 mph) or more
Engine speed 1000 rpm or more

TYPICAL MALFUNCTION THRESHOLDS

Starter signal ON

CONFIRMATION DRIVING PATTERN

A231469E15
1.229,1.979 1.604,2.156 0.375,0.177 10 false Idling 0.396,2.25 1.604,2.573 1.208,0.323 10 false Ignition Switch ON 0.354,0.813 1.667,0.99 1.313,0.177 10 false 20 km/h (12.4 mph) 2.396,2.854 3.083,3.167 0.688,0.313 10 false 5 seconds or more 3.594,2.938 4.865,3.104 1.271,0.167 10 false 20 seconds or more 2,2.333 2.25,2.521 0.25,0.188 10 false [A] 2.583,2.125 2.792,2.302 0.208,0.177 10 false [B] 4.031,0.458 4.26,0.625 0.229,0.167 10 false [C] 4.906,3.344 5.135,3.51 0.229,0.167 10 false [D]

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on [A].

6.

Idle the engine for 5 seconds or more [B].

7.

Drive the vehicle at 20 km/h (12.4 mph) or more for 20 seconds or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


8.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

11.

Input the DTC: P0617.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [C] and [D] again and, if necessary, extend the driving time.




WIRING DIAGRAM

A303496E02
0.083,0.115 5.958,0.354 5.875,0.24 12 false w/ Smart Entry and Start System: 1.813,1.49 1.969,1.688 0.156,0.198 10 false 6 5.417,1.479 5.573,1.677 0.156,0.198 10 false 7 5.333,1.667 5.625,1.865 0.292,0.198 10 false F82 5.646,1.656 6.115,1.854 0.469,0.198 10 false NEO 5.656,2.219 6.125,2.417 0.469,0.198 10 false NSW 5.344,2.219 5.635,2.417 0.292,0.198 10 false F82 5.417,2.042 5.573,2.24 0.156,0.198 10 false 9 5.375,3.448 5.729,3.646 0.354,0.198 10 false 19 5.344,3.646 5.635,3.844 0.292,0.198 10 false F82 5.656,3.542 6.083,3.74 0.427,0.198 10 false STA 6.094,4.688 6.521,4.885 0.427,0.198 10 false ECM 1.75,1.677 2.042,1.875 0.292,0.198 10 false F43 1.74,2.208 2.031,2.406 0.292,0.198 10 false F44 1.75,2.948 2.042,3.146 0.292,0.198 10 false F44 1.458,1.677 1.75,1.875 0.292,0.198 10 false NE 1.302,2.198 1.833,2.396 0.531,0.198 10 false STAR 1.385,2.938 1.917,3.135 0.531,0.198 10 false STA 1.781,2.021 2.146,2.208 0.365,0.188 10 false 16 1.792,2.771 2.115,2.969 0.323,0.198 10 false 37 2.438,2.344 2.969,2.542 0.531,0.198 10 false STA 0.021,3.25 2.896,3.479 2.875,0.229 10 false Certification ECU (Smart Key ECU Assembly) 3.365,2.573 3.521,2.771 0.156,0.198 10 false 5 3.521,2.573 3.677,2.771 0.156,0.198 10 false L 4.552,2.583 4.708,2.781 0.156,0.198 10 false B 4.729,2.583 4.885,2.781 0.156,0.198 10 false 4 3.313,2.938 3.688,3.146 0.375,0.208 10 false B19 3.313,3.104 5.115,3.469 1.802,0.365 10 false Park/Neutral Position Switch 2.552,3.906 2.708,4.104 0.156,0.198 10 false 5 2.99,3.906 3.146,4.104 0.156,0.198 10 false 2 2.99,4.802 3.146,5 0.156,0.198 10 false 1 2.552,4.802 2.708,5 0.156,0.198 10 false 3 3.219,4.323 3.75,4.521 0.531,0.198 10 false ST 0.531,4.365 1.063,4.563 0.531,0.198 10 false ST 1.719,5.479 2.073,5.698 0.354,0.219 10 false B15 1,5.688 1.354,5.906 0.354,0.219 10 false B28 0.708,6.969 1.24,7.167 0.531,0.198 10 false Battery 1.323,6.469 2.146,6.865 0.823,0.396 10 false Starter Assemblly 2.052,5.469 2.208,5.667 0.156,0.198 10 false 1 1.083,5.521 1.24,5.719 0.156,0.198 10 false 1 0.552,6.219 1.125,6.448 0.573,0.229 10 false FL MAIN

A300994E11
5.656,1.604 6.115,1.802 0.458,0.198 10 false NSW 5.677,3.365 6.135,3.563 0.458,0.198 10 false STA 3.375,2.26 3.833,2.458 0.458,0.198 10 false L 4.594,2.26 5.052,2.458 0.458,0.198 10 false B 4.792,2.25 5.25,2.448 0.458,0.198 10 false 4 3.198,2.26 3.656,2.458 0.458,0.198 10 false 5 3.177,2.708 3.635,2.906 0.458,0.198 10 false B19 3.188,2.865 5.635,3.083 2.448,0.219 10 false Park/Neutral Position Switch 1.042,2.156 2.719,2.531 1.677,0.375 10 false Ignition or Starter Switch Assembly 2.219,1.542 2.677,1.74 0.458,0.198 10 false ST2 1.063,1.542 1.521,1.74 0.458,0.198 10 false AM2 2.542,1.5 3,1.698 0.458,0.198 10 false 7 0.917,1.521 1.375,1.719 0.458,0.198 10 false 5 1.042,2.021 1.5,2.219 0.458,0.198 10 false F7 0.521,2.156 0.979,2.354 0.458,0.198 10 false AM2 0.542,3.115 1,3.313 0.458,0.198 10 false MAIN 1.521,3.698 1.979,3.896 0.458,0.198 10 false ST 3.25,4.302 3.708,4.5 0.458,0.198 10 false ST 2.646,3.813 3.104,4.01 0.458,0.198 10 false 5 3.083,3.813 3.542,4.01 0.458,0.198 10 false 2 3.073,4.771 3.531,4.969 0.458,0.198 10 false 1 2.646,4.76 3.104,4.958 0.458,0.198 10 false 3 3.406,1.75 3.865,1.948 0.458,0.198 10 false STA 5.333,1.635 5.792,1.833 0.458,0.198 10 false F82 5.333,3.49 5.792,3.688 0.458,0.198 10 false F82 1.729,5.229 2.188,5.427 0.458,0.198 10 false B15 1.021,5.635 1.479,5.833 0.458,0.198 10 false B28 2.052,5.219 2.51,5.417 0.458,0.198 10 false 1 1.083,5.448 1.542,5.646 0.458,0.198 10 false 1 1.094,6.417 3.542,6.615 2.448,0.198 10 false Starter Assembly 0.708,6.938 1.781,7.135 1.073,0.198 10 false Battery 0.156,0.177 5.115,0.417 4.958,0.24 12 false w/o Smart Entry and Start System: 6.094,4.667 6.552,4.865 0.458,0.198 10 false ECM 5.406,1.448 5.865,1.646 0.458,0.198 10 false 9 5.365,3.313 5.823,3.51 0.458,0.198 10 false 19 0.542,6.073 1.167,6.271 0.625,0.198 10 false FL MAIN

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

The following troubleshooting flowchart is based on the premise that the engine is cranked normally.

If the engine will not crank, proceed to the Problem Symptoms Table.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM(for Automatic Transaxle)>PROBLEM SYMPTOMS TABLE

·

Read freeze frame data using the GTS. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data, from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

Powertrain > Engine and ECT > Data List
Tester Display
Starter Signal
50003 234 118

e.

Check the value displayed on the GTS when the vehicle is driven at 20 km/h (12.4 mph) or more.

NOTICE:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.



Result:
Condition GTS Display Proceed to
Driving at 20 km/h (12.4 mph) or more OFF A
ON B



A

B

2.READ VALUE USING GTS (STARTER SIGNAL)
2.READ VALUE USING GTS (STARTER SIGNAL)
a.

Disconnect the B19 park/neutral position switch connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

Powertrain > Engine and ECT > Data List
Tester Display
Starter Signal
50003 234 118

f.

Read the value displayed on the GTS when the ignition switch is ON.


Result:
Result Proceed to
ON A
OFF B



A

3.INSPECT ECM (STA TERMINAL VOLTAGE)

B

5.INSPECT PARK/NEUTRAL POSITION SWITCH
3.INSPECT ECM (STA TERMINAL VOLTAGE)
a.
A301477C03
1.656,1.594 2.063,1.813 0.406,0.219 2.323,2.875 1.958,2.198 true 0.198,0.125 0.51,0.323 0.313,0.198 10 false *a 1.74,1.615 2.198,1.813 0.458,0.198 10 false F82 2.167,2.896 2.625,3.094 0.458,0.198 10 false STA
*a Rear view of wire harness connector
(to ECM)


Disconnect the B19 park/neutral position switch connector.


b.

Disconnect the ECM connector.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.


Result:
Tester Connection Switch Condition Specified Condition Proceed to
F82-19 (STA) - Body ground Ignition switch ON 11 to 14 V A
*1
B
*2
Below 1.5 V C


*1: w/ smart entry and start system

*2: w/o smart entry and start system



A

4.CHECK HARNESS AND CONNECTOR (ST RELAY - PARK/NEUTRAL POSITION SWITCH - ECM - CERTIFICATION ECU(SMART KEY ECU ASSEMBLY))

B

REPAIR OR REPLACE HARNESS OR CONNECTOR (ST RELAY - PARK/NEUTRAL POSITION SWITCH - ECM)

C

4.CHECK HARNESS AND CONNECTOR (ST RELAY - PARK/NEUTRAL POSITION SWITCH - ECM - CERTIFICATION ECU(SMART KEY ECU ASSEMBLY))
a.

Remove the ST relay from the engine room relay block.


b.

Disconnect the B19 park/neutral position switch connector.


c.

Disconnect the F82 ECM connector.


d.

Disconnect the F44 certification ECU (smart key ECU assembly) connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
2 (ST relay), B19-5 (L), F82-19 (STA) or F44-37 (STA) - Body ground Always 10 kΩ or higher



Result:
Result
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT PARK/NEUTRAL POSITION SWITCH
a.
C193931C17
1.615,0.969 2,0.333 true 1.146,0.969 0.75,0.583 true 2.75,1.75 2.354,1.5 true 0.083,0.073 0.417,0.417 0.333,0.344 10 *a 0.583,0.469 0.74,0.667 0.156,0.198 10 B 2.792,1.719 3.042,1.969 0.25,0.25 10 L 2.042,0.229 2.281,0.479 0.24,0.25 10 RB
*a Component without harness connected
(Park/Neutral Position Switch)


Disconnect the B19 park/neutral position switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
4 (B) - 5 (L) Always 10 kΩ or higher
2 (RB) - 5 (L) Always 10 kΩ or higher



Result:
Result Proceed to
Outside standard range
(Tester Connection 4(B) - 5(L))
A
Outside standard range
(Tester Connection 2(RB) - 5(L))
B
Within standard range
(w/ smart entry and start system)
C
Within standard range
(w/o smart entry and start system)
D



A

6.REPLACE PARK/NEUTRAL POSITION SWITCH

B

C

7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM - CERTIFICATION ECU(SMART KEY ECU ASSEMBLY))

D

9.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
6.REPLACE PARK/NEUTRAL POSITION SWITCH

Result:
Result Proceed to
w/ smart entry and start system A
w/o smart entry and start system B



A

7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM - CERTIFICATION ECU(SMART KEY ECU ASSEMBLY))

B

9.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM - CERTIFICATION ECU(SMART KEY ECU ASSEMBLY))
a.

Disconnect the B19 park/neutral position switch connector.


b.

Disconnect the F82 ECM connector.


c.

Disconnect the F44 certification ECU (smart key ECU assembly) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
B19-4 (B), F82-9 (NSW) or F44-16 (STAR) - Body ground Always 10 kΩ or higher



Result:
Result
OK
NG



OK

8.INSPECT ECM (NSW TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT ECM (NSW TERMINAL VOLTAGE)
a.

Disconnect the ECM connector.


b.
A301477C01
1.656,1.594 2.063,1.813 0.406,0.219 2.323,2.875 1.927,2.156 true 0.198,0.125 0.51,0.323 0.313,0.198 10 false *a 1.74,1.615 2.198,1.813 0.458,0.198 10 false F82 2.167,2.896 2.625,3.094 0.458,0.198 10 false NSW
*a Rear view of wire harness connector
(to ECM)


Disconnect the B19 park/neutral position switch connector.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F82-9 (NSW) - Body ground Ignition switch ON Below 1.5 V



Result:
Result
OK
NG



OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

9.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
a.

Inspect the ignition or starter switch assembly.

Click hereEngine / Hybrid System>2NZ-FE STARTING>IGNITION SWITCH>INSPECTION


Result:
Result
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM - IGNITION OR STARTER SWITCH ASSEMBLY)

NG

REPLACE PARK/NEUTRAL POSITION SWITCH

10.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM - IGNITION OR STARTER SWITCH ASSEMBLY)
a.

Disconnect the B19 park/neutral position switch connector.


b.

Disconnect the F82 ECM connector.


c.

Disconnect the F7 ignition or starter switch assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
B19-4(B), F82-9 (NSW) or F7-7 (ST2) - Body ground Always 10 kΩ or higher



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR