Home › Engine / Hybrid System › 2NZ-FE ENGINE CONTROL › SFI SYSTEM(for Manual Transaxle) › 2013.08–2016.10
RM30M0E _51 Engine / Hybrid System _017072 2NZ-FE ENGINE CONTROL _0090868 SFI SYSTEM(for Manual Transaxle) C

2NZ-FE ENGINE CONTROL  SFI SYSTEM(for Manual Transaxle)  P0136  Oxygen Sensor Circuit (Bank 1 Sensor 2)  


DESCRIPTION

Refer to DTC P0031.

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM(for Manual Transaxle)>P0031

HINT:

Sensor 2 refers to the sensor mounted behind the Three-Way Catalytic Converter (TWC) and located far from the engine assembly.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0136 Oxygen Sensor Circuit (Bank 1 Sensor 2) Following conditions (a) and (b) met for 6 minutes or more after engine warmed up (2 trip detection logic):

(a) Vehicle driven in 1 STOP-and-GO* cycles

(b) Heated oxygen sensor (sensor 2) voltage remains at 0.4 V or higher or 0.5 V or less


·

Open or short in heated oxygen sensor (sensor 2) circuit

·

Heated oxygen sensor (sensor 2)

·

Heated oxygen sensor (sensor 2) heater


Comes on DTC stored

HINT:

*: STOP refers to a vehicle speed of less than 5 km/h (3 mph) and GO refers to a vehicle speed of 100 km/h (62 mph) or more.


MONITOR DESCRIPTION

The ECM monitors the heated oxygen sensor (sensor 2) to check for the following malfunctions. If any of the malfunctions are detected, the ECM illuminates the MIL and stores a DTC.

·

The heated oxygen sensor (sensor 2) output voltage remains above 0.5 V (rich) or below 0.4 V (lean) while the vehicle is accelerated and decelerated for 4 minutes or more.


MONITOR STRATEGY

Required Sensor/Components (Main) Heated oxygen sensor (sensor 2)
Required Sensor/Components (Related) Engine coolant temperature sensor
Mass air flow meter
Vehicle speed sensor
Throttle body with motor assembly
Frequency of operation Once per driving cycle

TYPICAL ENABLING CONDITIONS

Heated oxygen sensor output voltage:
All of the following conditions A to C are met -
A. Engine Running
B. Time after engine starts 0 seconds or more
C. Cumulative time while heated oxygen sensor is ON 22 seconds or more

TYPICAL MALFUNCTION THRESHOLDS

Heated oxygen sensor output voltage
All of the following conditions are met -
Frequency of switch time between less than 0.4 V and 0.5 V or higher 0 times
Cumulative rear oxygen sensor monitor time 190 seconds or more

CONFIRMATION DRIVING PATTERN

A260198E02
0.115,0.583 1.302,0.781 1.188,0.198 10 false 100 km/h (62 mph) 0.969,2.031 1.344,2.24 0.375,0.208 10 false Idling 0.188,2.375 1.375,2.583 1.188,0.208 10 false Ignition switch ON 1.938,3.063 3.26,3.271 1.323,0.208 10 false 60 seconds or more 3.729,3.042 5,3.25 1.271,0.208 10 false 5 minutes or more 5.625,3.063 6.396,3.396 0.771,0.333 10 false 10 seconds or more 2.396,1.917 2.677,2.135 0.281,0.219 10 false [A] 4.198,0.438 4.563,0.698 0.365,0.26 10 false [B] 6.021,1.917 6.26,2.156 0.24,0.24 10 false [C] 6.333,3.552 6.563,3.74 0.229,0.188 10 false [D]

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch on and turn the GTS on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch and turn the GTS on.

6.

Start the engine and idle it for 60 seconds or more [A].

7.

Drive the vehicle at more than 100 km/h (62 mph) for 5 minutes or more [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


8.

Allow the engine to idle for 10 seconds or more [C].

9.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].

10.

Read the pending DTC.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0136.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [D].




CAUTION / NOTICE / HINT

HINT:

Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F Sensor function provided in the Active Test. The Control the Injection Volume for A/F Sensor function can help to determine whether the heated oxygen sensor and other potential trouble areas are malfunctioning.

The following instructions describe how to conduct the Control the Injection Volume for A/F Sensor operation using the GTS.

1.

Connect the GTS to the DLC3.

2.

Start the engine.

3.

Turn the GTS on.

4.

Warm up the engine and run the engine at an engine speed of 2500 rpm for approximately 90 seconds.

5.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / O2S B1S1 and O2S B1S2.

6.

Perform the Active Test operation with the engine idling (press the 12.5% or -12.5% button to change the fuel injection volume).

7.

Monitor the output voltages of the heated oxygen sensors (O2S B1S1 and O2S B1S2) displayed on the GTS.



HINT:
·

The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

Each sensor reacts in accordance with increases and decreases in the fuel injection volume.



GTS Display
(Sensor)
Injection Volume Status Voltage
O2S B1S1
Heated oxygen sensor (sensor 1)
12.5% Rich Higher than 0.5 V
-12.5% Lean Below 0.4 V
O2S B1S2
Heated oxygen sensor (sensor 2)
12.5% Rich Higher than 0.5 V
-12.5% Lean Below 0.4 V

NOTICE:

The heated oxygen sensor (sensor 1) has an output delay of a few seconds and the heated oxygen sensor (sensor 2) has a maximum output delay of approximately 20 seconds.


A299377E01
3.375,0.313 5.552,0.698 2.177,0.385 10 false Heated Oxygen Sensor (Sensor 2) Output Voltage 0.885,0.323 3.063,0.708 2.177,0.385 10 false Heated Oxygen Sensor (Sensor 1) Output Voltage 0.406,1.771 0.563,1.979 0.156,0.208 10 false 1 0.281,0.406 0.677,0.604 0.396,0.198 10 false Case 5.802,0.323 6.823,0.729 1.021,0.406 10 false Main Suspected Trouble Area 0.417,3.75 0.594,3.969 0.177,0.219 10 false 2 0.427,5.688 0.583,5.896 0.156,0.208 10 false 3 0.438,7.74 0.594,7.948 0.156,0.208 10 false 4 6.208,1.813 6.344,2.01 0.135,0.198 10 false - 5.677,3.094 6.833,3.531 1.156,0.438 10 false - Heated oxygen sensor (sensor 1) 5.677,3.542 6.698,4.125 1.021,0.583 10 false - Heated oxygen sensor (sensor 1) heater 5.688,4.135 6.708,4.719 1.021,0.583 10 false - Heated oxygen sensor (sensor 1) circuit 5.677,5.104 6.781,5.479 1.104,0.375 10 false - Heated oxygen sensor (sensor 2) 5.677,5.521 6.729,6.094 1.052,0.573 10 false - Heated oxygen sensor (sensor 2) heater 5.688,6.125 6.719,6.698 1.031,0.573 10 false - Heated oxygen sensor (sensor 2) circuit 5.688,7.01 6.615,7.438 0.927,0.427 10 false - Fuel injector assembly 5.677,7.427 6.646,7.625 0.969,0.198 10 false - Fuel pressure 5.677,7.698 6.74,8.594 1.063,0.896 10 false - Gas leak from exhaust system (Air fuel ratio extremely rich or lean) 1.469,1.25 1.927,1.448 0.458,0.198 10 false 12.5% 1.51,3.198 1.969,3.406 0.458,0.208 10 false 12.5% 3.969,3.208 4.427,3.417 0.458,0.208 10 false 12.5% 3.958,1.25 4.448,1.438 0.49,0.188 10 false 12.5% 1.51,7.125 1.979,7.354 0.469,0.229 10 false 12.5% 1.521,5.156 1.979,5.344 0.458,0.188 10 false 12.5% 3.979,5.167 4.438,5.354 0.458,0.188 10 false 12.5% 3.979,7.125 4.417,7.333 0.438,0.208 10 false 12.5% 1.417,1.521 1.906,1.708 0.49,0.188 10 false -12.5% 3.906,1.51 4.396,1.698 0.49,0.188 10 false -12.5% 3.917,3.458 4.406,3.646 0.49,0.188 10 false -12.5% 1.458,3.469 1.948,3.656 0.49,0.188 10 false -12.5% 1.469,5.406 1.958,5.594 0.49,0.188 10 false -12.5% 3.938,5.406 4.427,5.594 0.49,0.188 10 false -12.5% 3.938,7.385 4.427,7.573 0.49,0.188 10 false -12.5% 1.458,7.375 1.948,7.563 0.49,0.188 10 false -12.5% 0.76,1 1.813,1.229 1.052,0.229 10 false Injection Volume 0.792,1.927 1.729,2.156 0.938,0.229 10 false Output Voltage 0.792,8.208 2.052,8.406 1.26,0.198 10 false Almost no reaction 3.26,8.208 4.521,8.406 1.26,0.198 10 false Almost no reaction 0.781,4.302 2.042,4.5 1.26,0.198 10 false Almost no reaction 3.26,6.26 4.521,6.458 1.26,0.198 10 false Almost no reaction 5.042,8.104 5.302,8.292 0.26,0.188 10 false NG 2.563,8.104 2.823,8.292 0.26,0.188 10 false NG 5.031,6.146 5.292,6.333 0.26,0.188 10 false NG 2.552,4.198 2.813,4.385 0.26,0.188 10 false NG 3.229,1 4.281,1.229 1.052,0.229 10 false Injection Volume 3.229,2.948 4.281,3.177 1.052,0.229 10 false Injection Volume 0.76,2.948 1.813,3.177 1.052,0.229 10 false Injection Volume 0.75,4.906 1.802,5.135 1.052,0.229 10 false Injection Volume 3.229,4.906 4.281,5.135 1.052,0.229 10 false Injection Volume 3.219,6.854 4.271,7.083 1.052,0.229 10 false Injection Volume 0.771,6.865 1.823,7.094 1.052,0.229 10 false Injection Volume 0.844,2.271 1.969,2.469 1.125,0.198 10 false Higher than 0.5 V 1.167,2.49 1.99,2.677 0.823,0.188 10 false Below 0.4 V 3.323,2.219 4.448,2.417 1.125,0.198 10 false Higher than 0.5 V 3.646,2.448 4.469,2.635 0.823,0.188 10 false Below 0.4 V 3.25,1.917 4.188,2.146 0.938,0.229 10 false Output Voltage 5.125,2.333 5.406,2.531 0.281,0.198 10 false OK 2.646,2.375 2.927,2.573 0.281,0.198 10 false OK 0.802,3.885 1.74,4.115 0.938,0.229 10 false Output Voltage 3.26,3.885 4.198,4.115 0.938,0.229 10 false Output Voltage 5.135,4.302 5.417,4.5 0.281,0.198 10 false OK 3.344,4.198 4.469,4.396 1.125,0.198 10 false Higher than 0.5 V 3.656,4.427 4.479,4.615 0.823,0.188 10 false Below 0.4 V 3.271,5.854 4.208,6.083 0.938,0.229 10 false Output Voltage 0.802,5.844 1.74,6.073 0.938,0.229 10 false Output Voltage 0.865,6.146 1.99,6.344 1.125,0.198 10 false Higher than 0.5 V 1.177,6.385 2,6.573 0.823,0.188 10 false Below 0.4 V 2.667,6.26 2.948,6.458 0.281,0.198 10 false OK 0.802,7.781 1.74,8.01 0.938,0.229 10 false Output Voltage 3.271,7.781 4.208,8.01 0.938,0.229 10 false Output Voltage

HINT:
·

Following the Control the Injection Volume for A/F Sensor procedure enables technicians to check and graph the voltage outputs of both the heated oxygen sensors.

·

To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / O2S B1S1 and O2S B1S2, and then press the graph button on the Data List view.

·

If the OX1B wire from the ECM connector is short-circuited to the +B wire, DTC P0136 will be stored.



NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Result Proceed to
DTC P0136 is output A
DTC P0136 and other DTCs are output B


HINT:

If any DTCs other than P0136 are output, troubleshoot those DTCs first.



A

2.READ VALUE USING GTS (O2S B1S2)

B

2.READ VALUE USING GTS (O2S B1S2)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / O2S B1S2.

Powertrain > Engine and ECT > Data List
Tester Display
O2S B1S2
50003 234 44

d.

Allow the engine to run at 2500 rpm for 3 minutes.


e.

Depress the accelerator pedal quickly until the engine rpm reaches 4000 rpm 3 times.

Standard voltage:

Heated oxygen sensor voltage alternates between below 0.4 V and 0.5 V or higher.


A128474E11
1.441,0.459 1.745,0.642 0.304,0.184 10 1 V 2.468,0.216 2.772,0.399 0.304,0.184 10 OK 3.422,0.216 3.726,0.399 0.304,0.184 10 NG 4.376,0.216 4.680,0.399 0.304,0.184 10 NG 5.33,0.216 5.634,0.399 0.304,0.184 10 NG 1.357,0.725 1.825,0.908 0.468,0.184 10 0.5 V 1.357,0.991 1.744,1.175 0.387,0.184 10 0.4 V 1.441,1.257 1.745,1.441 0.304,0.184 10 0 V


Result:
Result Proceed to
NG A
OK B



A

3.INSPECT HEATED OXYGEN SENSOR (SENSOR 2) (HEATER RESISTANCE)

B

7.PERFORM CONFIRMATION DRIVING PATTERN
3.INSPECT HEATED OXYGEN SENSOR (SENSOR 2) (HEATER RESISTANCE)
a.

Result:
Proceed to
OK
NG



OK

4.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR (SENSOR 2))

NG

4.CHECK TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR (SENSOR 2))
a.
A215512C01
0.604,1 0.969,1.25 0.365,0.25 1.927,0.896 2.281,0.573 true 0.156,0.146 0.344,0.333 0.188,0.188 10 false *a 0.667,1.042 0.948,1.219 0.281,0.177 10 false F58 2.323,0.458 2.542,0.646 0.219,0.188 10 false +B
*a Front view of wire harness connector
(to Heated Oxygen Sensor (Sensor 2))


Disconnect the heated oxygen sensor (sensor 2) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F58-2 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 2) - ECM)

NG

6.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 2) - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)
5.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 2) - ECM)
a.

Disconnect the F58 heated oxygen sensor (sensor 2) connector.


b.

Disconnect the B30 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connections Condition Specified Condition
F58-1 (HT1B) - B30-7 (HT1B) Always Below 1 Ω
F58-3 (OX1B) - B30-17 (OX1B) Always Below 1 Ω
F58-4 (E2) - B30-18 (EX1B) Always Below 1 Ω
F58-1 (HT1B) - B30-7 (HT1B) - Body ground Always 10 kΩ or higher
F58-3 (OX1B) - B30-17 (OX1B) - Body ground Always 10 kΩ or higher
F58-4 (E2) - B30-18 (EX1B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 2) - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the F58 heated oxygen sensor (sensor 2) connector.


b.

Remove the driver side junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F58-2 (+B) - 2H-4 Always Below 1 Ω
F58-2 (+B) or 2H-4 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.PERFORM CONFIRMATION DRIVING PATTERN
a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


Result:
Proceed to
NEXT



NEXT

8.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136)
8.CHECK WHETHER DTC OUTPUT RECURS (DTC P0136)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Result Proceed to
DTC P0136 is output A
DTC is not output B



A

B