Home › Engine / Hybrid System › 1NZ-FE ENGINE MECHANICAL › ENGINE UNIT › 2013.08–2016.10
RM30M0E _51 Engine / Hybrid System _017073 1NZ-FE ENGINE MECHANICAL _0091007 ENGINE UNIT G

1NZ-FE ENGINE MECHANICAL  ENGINE UNIT  INSPECTION  


PROCEDURE

Hide 13506 1.INSPECT CHAIN SUB-ASSEMBLY

A301959C01
1.667,1.208 1.979,1.365 0.313,0.156 10 false *a 0.677,1.854 0.833,2.052 0.156,0.198 10 false 0 0.823,1.854 0.979,2.052 0.156,0.198 10 false 1 0.99,1.854 1.146,2.052 0.156,0.198 10 false 2 1.146,1.854 1.302,2.052 0.156,0.198 10 false 3 1.302,1.854 1.458,2.052 0.156,0.198 10 false 4 1.469,1.854 1.625,2.052 0.156,0.198 10 false 5 2.688,1.844 2.927,2.063 0.24,0.219 10 false 15
*a Measuring Area


a.

Using a spring scale and vernier caliper, apply 140 N (14.3 kgf, 31.5 lbf) to the chain sub-assembly and measure its length.

Maximum chain elongation:

123.2 mm (4.850 in.)


HINT:

Perform the same measurement at 3 or more random places and calculate the average length.


If the chain elongation is greater than the maximum, replace the chain sub-assembly.


Hide 13540 2.INSPECT NO. 1 CHAIN TENSIONER ASSEMBLY

A301957C01
1.135,0.906 1.469,1.26 true 2.615,0.927 2.948,1.281 true 1.052,1.448 1.385,1.802 true 2.51,1.458 2.844,1.813 true 1.521,1.198 1.833,1.354 0.313,0.156 10 false *1 1.427,1.74 1.74,1.896 0.313,0.156 10 false *2 3,1.219 3.313,1.375 0.313,0.156 10 false *1 2.885,1.75 3.198,1.906 0.313,0.156 10 false *2
*1 Ratchet Pawl
*2 Plunger


a.

Check that the plunger moves smoothly when the ratchet pawl is raised with your finger.


b.

Release the ratchet pawl and check that the plunger is locked in place by the ratchet pawl and does not move when pushed with your finger.

If necessary, replace the No. 1 chain tensioner assembly.


Hide 13559 3.INSPECT CHAIN TENSIONER SLIPPER

A130438E01
0.688,1.031 0.844,1.229 0.156,0.198 10 false A 1.292,0.771 1.448,0.969 0.156,0.198 10 false A 2.094,0.469 2.448,0.667 0.354,0.198 10 false A-A

a.

Using a vernier caliper, measure the chain tensioner slipper wear.

Minimum wear:

1.0 mm (0.039 in.)


If the wear is less than the minimum, replace the chain tensioner slipper.


Hide 13561 4.INSPECT NO. 1 CHAIN VIBRATION DAMPER

A130439E01
0.531,0.948 0.688,1.146 0.156,0.198 10 false A 1.146,0.729 1.302,0.927 0.156,0.198 10 false A 2.083,0.531 2.396,0.75 0.313,0.219 10 false A-A

a.

Using a vernier caliper, measure the No. 1 chain vibration damper wear.

Minimum wear:

1.0 mm (0.039 in.)


If the wear is less than the minimum, replace the No. 1 chain vibration damper.


Hide 13511 5.INSPECT CAMSHAFT

E273784

a.

Inspect the camshaft for runout.

i.

Place the camshaft on V-blocks.


ii.

Using a dial indicator, measure the circle runout at the center journal.

Maximum circle runout:

0.03 mm (0.0012 in.)


If the circle runout is greater than the maximum, replace the camshaft.



b.
A303052

Inspect the cam lobes.

i.

Using a micrometer, measure the cam lobe height.

Standard cam lobe height:

44.617 to 44.717 mm (1.7566 to 1.7605 in.)


Minimum cam lobe height:

43.16 mm (1.66962 in.)


If the cam lobe height is less than the minimum, replace the camshaft.



c.
A303053

Inspect the camshaft journals.

i.

Using a micrometer, measure the journal diameter.

Standard Journal Diameter:
Journal Specified Condition
No. 1 journal 34.449 to 34.465 mm
(1.3563 to 1.3569 in.)
Other journals 22.959 to 22.975 mm
(0.9039 to 0.9045 in.)


If the journal diameter is not as specified, check the oil clearance.



Hide 13512 6.INSPECT NO. 2 CAMSHAFT

a.

Inspect the No. 2 camshaft for runout.

i.

Place the No. 2 camshaft on V-blocks.


ii.

Using a dial indicator, measure the circle runout at the center journal.

Maximum circle runout:

0.03 mm (0.0012 in.)


If the circle runout is greater than the maximum, replace the No. 2 camshaft.



b.

Inspect the cam lobes.

i.

Using a micrometer, measure the cam lobe height.

Standard cam lobe height:

44.666 to 44.766 (1.7585 to 1.7624 in.)


Minimum cam lobe height:

44.52 mm (1.7528 in.)


If the cam lobe height is less than the minimum, replace the No. 2 camshaft.



c.

Inspect the No. 2 camshaft journals.

i.

Using a micrometer, measure the journal diameter.

Standard Journal Diameter:
Journal Specified Condition
No. 1 journal 34.449 to 34.465 mm
(1.3563 to 1.3569 in.)
Other journals 22.959 to 22.975 mm
(0.9039 to 0.9045 in.)


If the journal diameter is not as specified, check the oil clearance.



Hide 13050 7.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

a.
A130436

Check the gear diameter (with chain sub-assembly).

i.

Wrap the chain sub-assembly around the camshaft timing gear assembly.


ii.

Using a vernier caliper, measure the diameter of the camshaft timing gear assembly with the chain sub-assembly.

Minimum gear diameter (with chain sub-assembly):

96.2 mm (3.787 in.)


NOTICE:

Make sure that the vernier caliper is in contact with the chain link when measuring.


If the diameter is less than the minimum, replace the camshaft timing gear assembly.




c.

Check the lock of camshaft timing gear assembly.

i.

Clamp the camshaft in a vise, and check that the camshaft timing gear assembly is locked.

NOTICE:

Do not damage the camshaft.




d.
A116226C04
1.354,2.917 0.833,3.26 true 1.969,3.031 2.656,2.802 true 1.396,3.229 0.875,3.604 true 1.365,3.448 0.813,3.885 true 2.031,3.281 2.625,3.854 true 1.906,3.208 2.5,3.292 true 1.552,0.969 0.938,0.229 0.938,0.229 1.854,0.958 true 1.583,1.135 2.156,1.531 2.156,1.531 1.865,1.125 true 2.656,3.823 2.823,3.99 0.167,0.167 10 false *a 0.615,3.833 0.781,4 0.167,0.167 10 false *b 2.208,1.51 2.375,1.677 0.167,0.167 10 false *c 0.76,0.115 0.927,0.281 0.167,0.167 10 false *d 2.688,2.698 2.854,2.865 0.167,0.167 10 false *e 2.531,3.219 2.698,3.385 0.167,0.167 10 false *f 0.646,3.531 0.813,3.698 0.167,0.167 10 false *e 0.635,3.219 0.802,3.385 0.167,0.167 10 false *f
*a Rubber Piece
*b Vinyl Tape
*c Advance Side Path
*d Retard Side Path
*e Open
*f Closed


Release the lock pin.

i.

Cover the 4 oil paths of the cam journal with the vinyl tape as shown in the illustration.

HINT:

One of the 2 grooves located on the cam journal is for retarding cam timing (upper) and other is for advancing cam timing (lower). Each groove has 2 oil paths. Plug one of the oil paths for each groove with a rubber piece before wrapping the cam journal with the vinyl tape.



ii.

Prick a hole in the vinyl tape covering the advance oil path and retard oil path on the opposite side from the advance oil path.


iii.
A116227C04
1.604,0.885 0.875,0.354 true 1.833,0.958 2.583,0.333 true 0.667,0.219 0.833,0.375 0.167,0.156 10 false *a 2.604,0.177 2.781,0.323 0.177,0.146 10 false *b
*a Retard Side Path
*b Advance Side Path


Apply compressed air of approximately 150 kPa (1.5 kgf/cm2, 22 psi) pressure into the 2 broken paths (the advance side path and retard side path).

NOTICE:

Cover the paths with a piece of cloth to prevent oil splashes.



iv.
A116228C04
1.885,1.677 2.5,0.833 true 1.563,1.615 0.844,0.833 true 2.521,0.708 2.698,0.865 0.177,0.156 10 false *b 0.677,0.708 0.854,0.865 0.177,0.156 10 false *a 2.75,2.667 2.948,2.844 0.198,0.177 10 false *d 0.563,2.667 0.75,2.844 0.188,0.177 10 false *c
*a Retard Side Path
*b Advance Side Path
*c Decompress
*d Hold Pressure


Confirm that the camshaft timing gear assembly revolves in the timing advance direction when the air pressure on the timing retard path is reduced.

HINT:

The lock pin is released and camshaft timing gear assembly revolves in the advance direction.



v.

When the camshaft timing gear assembly reaches the most advanced position, release the air pressure on the timing retard side path, and then release the air pressure on the timing advance side path.

NOTICE:

Camshaft timing gear assembly occasionally shifts to the retard side abruptly if the air pressure on the advance side path is released first. It often results in the breakage of the lock pin.




e.

Check the rotation.

i.

Rotate the camshaft timing gear assembly back and forth several times, except where the lock pin meets it at the most retarded angle. Check the movable range and that it rotates smoothly.

Standard:

Smooth movable range is approximately 22.5°


NOTICE:

Perform this check by hand, instead of using air pressure.


If necessary, replace the camshaft timing gear assembly.



f.

Check the lock in the most retarded position.

i.

Confirm that the camshaft timing gear assembly is locked in the most retarded position.




Hide 13523 8.INSPECT CAMSHAFT TIMING SPROCKET

A130437

a.

Wrap the chain sub-assembly around the camshaft timing sprocket.


b.

Using a vernier caliper, measure the diameter of the camshaft timing sprocket with the chain sub-assembly.

Minimum gear diameter (with chain sub-assembly):

96.2 mm (3.787 in.)


NOTICE:

Make sure that the vernier caliper is in contact with the chain link when measuring.


If the diameter is less than the minimum, replace the camshaft timing sprocket.


Hide 11101A 9.INSPECT CYLINDER HEAD SET BOLT

A301994C01
1.698,0.49 2.01,0.646 0.313,0.156 10 false *a
*a Measurement Length


a.

Using a vernier caliper, measure the length of the cylinder head set bolt from the seat to the end.

Standard bolt length:

142.8 to 144.2 mm (5.6220 to 5.6772 in.)


Maximum bolt length:

147.1 mm (5.7913 in.)


If the bolt length is greater than the maximum, replace the cylinder head set bolt.