Home › Engine / Hybrid System › 1NZ-FE ENGINE MECHANICAL › CYLINDER HEAD › 2013.08–2016.10
RM30M0E _51 Engine / Hybrid System _017073 1NZ-FE ENGINE MECHANICAL _0091008 CYLINDER HEAD G

1NZ-FE ENGINE MECHANICAL  CYLINDER HEAD  INSPECTION  


PROCEDURE

Hide 1.INSPECT CYLINDER HEAD FOR WARPAGE

a.
A105858C01
0.656,1.531 0.969,1.688 0.313,0.156 10 false *a 0.646,2.771 0.958,2.927 0.313,0.156 10 false *b 0.656,3.615 0.969,3.771 0.313,0.156 10 false *c
*a Cylinder Block Side
*b Intake Manifold Side
*c Exhaust Manifold Side


Using a precision straightedge and feeler gauge, measure the warpage of the surface that is in contact with the cylinder block and manifolds.

Maximum Warpage:
Surface Specified Condition
Cylinder block side 0.05 mm (0.0020 in.)
Intake manifold side 0.10 mm (0.0039 in.)
Exhaust manifold side 0.10 mm (0.0039 in.)


If the warpage is greater than the maximum, replace the cylinder head sub-assembly.


Hide 2.INSPECT CYLINDER HEAD FOR CRACKS

a.
A301949

Using a dye penetrant, check the combustion chamber, intake ports, exhaust ports and cylinder block surface for cracks.

If cracked, replace the cylinder head sub-assembly.


Hide 13711 3.INSPECT INTAKE VALVE

a.
A301997C01
1.927,0.917 2.24,1.073 0.313,0.156 10 false *a
*a Overall Length


Check the overall valve length.

Standard overall length:

89.25 mm (3.5138 in.)


Minimum overall length:

88.75 mm (3.4941 in.)


If the overall length is less than the minimum, replace the intake valve.


b.
A301998

Using a micrometer, measure the diameter of the valve stem.

Standard valve stem diameter:

4.970 to 4.985 mm (0.1957 to 0.1963 in.)


If the valve stem diameter is not as specified, inspect the valve guide bush oil clearance.


c.
A301995C01
0.75,1.583 1.063,1.74 0.313,0.156 10 false *a
*a Margin Thickness


Check the valve head margin thickness.

Standard margin thickness:

1.0 mm (0.039 in.)


Minimum margin thickness:

0.5 mm (0.020 in.)


If the margin thickness is less than the minimum, replace the intake valve.


Hide 13715 4.INSPECT EXHAUST VALVE

a.

Check the overall valve length.

Standard overall length:

87.90 mm (3.4606 in.)


Minimum overall length:

87.40 mm (3.4409 in.)


If the overall length is less than the minimum, replace the exhaust valve.


b.

Using a micrometer, measure the diameter of the valve stem.

Standard valve stem diameter:

4.965 to 4.980 mm (0.1955 to 0.1961 in.)


If the valve stem diameter is not as specified, inspect the valve guide bush oil clearance.


c.

Check the valve head margin thickness.

Standard margin thickness:

1.15 mm (0.045 in.)


Minimum margin thickness:

0.5 mm (0.020 in.)


If the margin thickness is less than the minimum, replace the exhaust valve.


Hide 5.INSPECT VALVE GUIDE BUSH OIL CLEARANCE

a.
A301956

Using a caliper gauge, measure the inside diameter of the valve guide bush.

Bush inside diameter:

5.010 to 5.030 mm (0.1972 to 0.1980 in.)



b.

Subtract the valve stem diameter measurement from the valve guide bush inside diameter measurement.

Standard Oil Clearance:
Valve Guide Bush Specified Condition
Intake 0.025 to 0.060 mm
(0.0010 to 0.0024 in.)
Exhaust 0.030 to 0.065 mm
(0.0012 to 0.0026 in.)


Maximum Oil Clearance:
Valve Guide Bush Specified Condition
Intake 0.08 mm (0.0032 in.)
Exhaust 0.10 mm (0.0039 in.)


If the clearance is greater than the maximum, replace the valve and valve guide bush.

Click hereEngine / Hybrid System>1NZ-FE ENGINE MECHANICAL>CYLINDER HEAD>REPLACEMENT


Hide 6.INSPECT VALVE SEAT

a.

Apply a light coat of Prussian blue to the valve face.


b.

Lightly press the valve against the seat.


c.
A301973C01
2.813,1.208 3.125,1.365 0.313,0.156 10 false *a
*a Width


Check the valve face and seat according to the following procedure.

i.

If blue appears 360° around the face, the valve is concentric. If not, replace the valve.


ii.

If blue appears 360° around the valve seat, the guide and face are concentric. If not, resurface the seat.


iii.

Check that the seat contact is in the middle of the valve face with the width between 1.0 to 1.4 mm (0.039 to 0.055 in.).



Hide 7.INSPECT VALVE SPRING

a.
A301996

Using a vernier caliper, measure the free length of the valve spring.

Standard free length:

45.05 to 45.15 mm (1.774 to 1.778 in.)


If the free length is not as specified, replace the valve spring.


b.
A249058C01
1.099,0.078 1.308,0.273 0.209,0.196 10 *a
*a Deviation


Using a steel square, measure the deviation of the valve spring.

Maximum deviation:

1.6 mm (0.063 in.)


Maximum angle (reference):

2°


If the deviation is greater than the maximum, replace the valve spring.


Hide 8.INSPECT CAMSHAFT THRUST CLEARANCE


b.
A301954

Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.

Standard thrust clearance:

0.040 to 0.095 mm (0.0016 to 0.0037 in.)


Maximum thrust clearance:

0.11 mm (0.0043 in.)


If the thrust clearance is greater than the maximum, replace the camshaft. If necessary, replace the bearing caps and cylinder head sub-assembly together.



Hide 9.INSPECT CAMSHAFT OIL CLEARANCE

a.

Clean the bearing caps and camshaft journals.


b.

Place the camshafts on the cylinder head sub-assembly.


c.
A301952C01
1.292,1.396 0.5,0.271 true 0.344,0.156 0.656,0.313 0.313,0.156 10 false *a
*a Plastigage


Lay a strip of Plastigage across each of the camshaft journals.


d.

Install the bearing caps.

Click hereEngine / Hybrid System>1NZ-FE ENGINE MECHANICAL>CAMSHAFT>INSTALLATION

NOTICE:

Do not turn the camshaft.




f.
A301953C01
0.333,0.479 1.24,1.427 true 0.156,0.375 0.469,0.573 0.313,0.198 10 false *a
*a Plastigage


Measure the Plastigage at its widest point.

Standard oil clearance:

0.035 to 0.072 mm (0.0014 to 0.0028 in.)


Maximum oil clearance:

0.08 mm (0.0031 in.)


If the oil clearance is greater than the maximum, replace the camshaft. If necessary, replace the bearing caps and cylinder head sub-assembly together.

NOTICE:

Completely remove the Plastigage.