13506
1.INSPECT CHAIN SUB-ASSEMBLY
| *a | Measuring Area |
Using a spring scale and vernier caliper, apply 140 N (14.3 kgf, 31.5 lbf) to the chain sub-assembly and measure its length.
123.2 mm (4.850 in.)
Perform the same measurement at 3 or more random places and calculate the average length.
If the chain elongation is greater than the maximum, replace the chain sub-assembly.
13540
2.INSPECT NO. 1 CHAIN TENSIONER ASSEMBLY
| *1 | Ratchet Pawl |
| *2 | Plunger |
Check that the plunger moves smoothly when the ratchet pawl is raised with your finger.
Release the ratchet pawl and check that the plunger is locked in place by the ratchet pawl and does not move when pushed with your finger.
13559
3.INSPECT CHAIN TENSIONER SLIPPER
Using a vernier caliper, measure the chain tensioner slipper wear.
1.0 mm (0.039 in.)
If the wear is less than the minimum, replace the chain tensioner slipper.
13561
4.INSPECT NO. 1 CHAIN VIBRATION DAMPER
Using a vernier caliper, measure the No. 1 chain vibration damper wear.
1.0 mm (0.039 in.)
If the wear is less than the minimum, replace the No. 1 chain vibration damper.
13511
5.INSPECT CAMSHAFT
Inspect the camshaft for runout.
Place the camshaft on V-blocks.
Using a dial indicator, measure the circle runout at the center journal.
0.03 mm (0.0012 in.)
If the circle runout is greater than the maximum, replace the camshaft.
Inspect the cam lobes.
Using a micrometer, measure the cam lobe height.
44.617 to 44.717 mm (1.7566 to 1.7605 in.)
43.16 mm (1.66962 in.)
If the cam lobe height is less than the minimum, replace the camshaft.
Inspect the camshaft journals.
Using a micrometer, measure the journal diameter.
| Journal | Specified Condition |
|---|---|
| No. 1 journal | 34.449 to 34.465 mm
(1.3563 to 1.3569 in.) |
| Other journals | 22.959 to 22.975 mm
(0.9039 to 0.9045 in.) |
If the journal diameter is not as specified, check the oil clearance.
13512
6.INSPECT NO. 2 CAMSHAFT
Inspect the No. 2 camshaft for runout.
Place the No. 2 camshaft on V-blocks.
Using a dial indicator, measure the circle runout at the center journal.
0.03 mm (0.0012 in.)
If the circle runout is greater than the maximum, replace the No. 2 camshaft.
Inspect the cam lobes.
Using a micrometer, measure the cam lobe height.
44.046 to 44.146 mm (1.7341 to 1.7380 in.)
43.90 mm (1.7283 in.)
If the cam lobe height is less than the minimum, replace the No. 2 camshaft.
Inspect the No. 2 camshaft journals.
Using a micrometer, measure the journal diameter.
| Journal | Specified Condition |
|---|---|
| No. 1 journal | 34.449 to 34.465 mm
(1.3563 to 1.3569 in.) |
| Other journals | 22.959 to 22.975 mm
(0.9039 to 0.9045 in.) |
If the journal diameter is not as specified, check the oil clearance.
13050
7.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY
Check the gear diameter (with chain sub-assembly).
Wrap the chain sub-assembly around the camshaft timing gear assembly.
Using a vernier caliper, measure the diameter of the camshaft timing gear assembly with the chain sub-assembly.
96.2 mm (3.787 in.)
Make sure that the vernier caliper is in contact with the chain link when measuring.
If the diameter is less than the minimum, replace the camshaft timing gear assembly.
Install the camshaft.
Click hereEngine / Hybrid System>2NZ-FE ENGINE MECHANICAL>ENGINE UNIT>REASSEMBLY
Check the lock of camshaft timing gear assembly.
Clamp the camshaft in a vise, and check that the camshaft timing gear assembly is locked.
Do not damage the camshaft.
| *a | Rubber Piece |
| *b | Vinyl Tape |
| *c | Advance Side Path |
| *d | Retard Side Path |
| *e | Open |
| *f | Closed |
Release the lock pin.
Cover the 4 oil paths of the cam journal with the vinyl tape as shown in the illustration.
One of the 2 grooves located on the cam journal is for retarding cam timing (upper) and other is for advancing cam timing (lower). Each groove has 2 oil paths. Plug one of the oil paths for each groove with a rubber piece before wrapping the cam journal with the vinyl tape.
Prick a hole in the vinyl tape covering the advance oil path and retard oil path on the opposite side from the advance oil path.
| *a | Retard Side Path |
| *b | Advance Side Path |
Apply compressed air of approximately 150 kPa (1.5 kgf/cm2, 22 psi) pressure into the 2 broken paths (the advance side path and retard side path).
Cover the paths with a piece of cloth to prevent oil splashes.
| *a | Retard Side Path |
| *b | Advance Side Path |
| *c | Decompress |
| *d | Hold Pressure |
Confirm that the camshaft timing gear assembly revolves in the timing advance direction when the air pressure on the timing retard path is reduced.
The lock pin is released and camshaft timing gear assembly revolves in the advance direction.
When the camshaft timing gear assembly reaches the most advanced position, release the air pressure on the timing retard side path, and then release the air pressure on the timing advance side path.
Camshaft timing gear assembly occasionally shifts to the retard side abruptly if the air pressure on the advance side path is released first. It often results in the breakage of the lock pin.
Check the rotation.
Rotate the camshaft timing gear assembly back and forth several times, except where the lock pin meets it at the most retarded angle. Check the movable range and that it rotates smoothly.
Smooth movable range is approximately 22.5°
Perform this check by hand, instead of using air pressure.
If necessary, replace the camshaft timing gear assembly.
Check the lock in the most retarded position.
Confirm that the camshaft timing gear assembly is locked in the most retarded position.
Remove the camshaft.
Click hereEngine / Hybrid System>2NZ-FE ENGINE MECHANICAL>ENGINE UNIT>DISASSEMBLY
13523
8.INSPECT CAMSHAFT TIMING SPROCKET
Wrap the chain sub-assembly around the camshaft timing sprocket.
Using a vernier caliper, measure the diameter of the camshaft timing sprocket with the chain sub-assembly.
96.2 mm (3.787 in.)
Make sure that the vernier caliper is in contact with the chain link when measuring.
If the diameter is less than the minimum, replace the camshaft timing sprocket.
11101A
9.INSPECT CYLINDER HEAD SET BOLT
| *a | Measurement Length |
Using a vernier caliper, measure the length of the cylinder head set bolt from the seat to the end.
142.8 to 144.2 mm (5.6220 to 5.6772 in.)
147.1 mm (5.7913 in.)
If the bolt length is greater than the maximum, replace the cylinder head set bolt.