Home › Drivetrain › C50 MANUAL TRANSMISSION / TRANSAXLE › DIFFERENTIAL OIL SEAL(for 1NZ-FE) › 2013.08–2016.07
RM30M0E _52 Drivetrain _017090 C50 MANUAL TRANSMISSION / TRANSAXLE _0091167 DIFFERENTIAL OIL SEAL(for 1NZ-FE) A

C50 MANUAL TRANSMISSION / TRANSAXLE  DIFFERENTIAL OIL SEAL(for 1NZ-FE)  REPLACEMENT  


PROCEDURE

Hide 1.REMOVE FRONT DRIVE SHAFT ASSEMBLIES

Hide 43420H 2.REMOVE FRONT DRIVE SHAFT OIL SEAL LH

a.
C289793N01
0.719,1.302 1.146,1.542 false 1.917,2.917 1.917,2.74 false 0.427,1.198 0.885,1.396 0.458,0.198 10 false SST 1.792,2.938 2.25,3.135 0.458,0.198 10 false SST

Using SST, remove the front drive shaft oil seal LH from the manual transaxle assembly.

SST
09308-00010  

NOTICE:

Do not damage the front drive shaft oil seal LH contact surface of the manual transaxle assembly.



Hide 43410M 3.REMOVE FRONT DRIVE SHAFT OIL SEAL RH

a.
C289794N01
2.375,1.99 2.375,1.417 true 1.479,2.917 1.479,2.708 false 2.25,2.021 2.708,2.219 0.458,0.198 10 false SST 1.344,2.927 1.802,3.125 0.458,0.198 10 false SST

Using SST, remove the front drive shaft oil seal RH from the manual transaxle assembly.

SST
09308-00010  

NOTICE:

Do not damage the front drive shaft oil seal RH contact surface of the manual transaxle assembly.



Hide 43420H 4.INSTALL FRONT DRIVE SHAFT OIL SEAL LH

a.
C289795C01
0.792,0.615 1.5,0.813 true 1.865,2.875 1.865,2.677 false 0.49,0.521 0.792,0.708 0.302,0.188 10 true SST 2.271,2.938 2.583,3.135 0.313,0.198 10 false *a 1.74,2.885 2.042,3.073 0.302,0.188 10 false SST
*a Drive in Depth


Using SST and a hammer, tap in a new front drive shaft oil seal LH to the manual transaxle assembly.

SST
09316-60011  (09316-00011)

Standard depth:

9.4 to 10.4 mm (0.371 to 0.409 in.)


NOTICE:
·

Be sure to install the front drive shaft oil seal LH in the correct direction.

·

Make sure to install the front drive shaft oil seal LH as specified, otherwise malfunctions such as a fluid leak will occur.




b.

Apply MP grease to the lip of the front drive shaft oil seal LH.


Hide 43410M 5.INSTALL FRONT DRIVE SHAFT OIL SEAL RH

a.
C289796C01
1.479,0.875 2.031,0.802 2.031,0.802 1.625,1.073 true 1.552,2.51 1.635,2.792 1.635,2.792 1.385,2.677 false 2.073,0.698 2.375,0.896 0.302,0.198 10 true SST 1.271,3.021 1.583,3.219 0.313,0.198 10 false *a 1.542,2.823 1.844,3.021 0.302,0.198 10 false SST
*a Drive in Depth


Using SST and a hammer, tap in a new front drive shaft oil seal RH to the manual transaxle assembly.

SST
09710-20011  (09710-06071)
09950-70010  (09951-07150)

Standard depth:

1.4 to 2.0 mm (0.0552 to 0.0787 in.)


NOTICE:
·

Be sure to install the front drive shaft oil seal RH in the correct direction.

·

Make sure to install the front drive shaft oil seal RH as specified, otherwise malfunctions such as a fluid leak will occur.




b.

Apply MP grease to the lip of the front drive shaft oil seal RH.