22030
1.INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY
Install a new throttle body gasket to the intake manifold.
Install the throttle body with motor assembly to the intake manifold with the bolt and 3 nuts.
If a component has been dropped or subjected to a strong impact, replace the throttle body with motor assembly.
Install the wire harness clamp bracket to the throttle body with motor assembly with the nut.
Connect the throttle body with motor assembly connector.
Engage the clamp to connect the wire harness to the wire harness clamp bracket.
16261
2.CONNECT WATER BY-PASS HOSE
Connect the water by-pass hose to the throttle body with motor assembly with the hose clip.
16264
3.CONNECT NO. 2 WATER BY-PASS HOSE
Connect the No. 2 water by-pass hose to the throttle body with motor assembly with the hose clip.
16522
4.INSTALL WATER FILLER BRACKET
Install the water filler bracket to the throttle body with motor assembly with the 2 nuts.
17735
5.INSTALL AIR CLEANER CAP WITH NO. 1 AIR CLEANER HOSE
Engage the 2 guides to install the air cleaner cap with No. 1 air cleaner hose to the air cleaner case sub-assembly and throttle body with motor assembly.
Engage the 2 clamps to secure the air cleaner cap to the air cleaner case sub-assembly.
Connect the No. 1 air cleaner hose to the throttle body with motor assembly and tighten the hose clamp.
Engage the 3 clamps to connect the wire harness to the air cleaner cap and purge VSV.
Connect the purge VSV connector and mass air flow meter connector.
17341T
6.CONNECT NO. 1 AIR HOSE (for Automatic Transaxle)
Connect the No. 1 air hose to the No. 1 air cleaner hose with the hose clip.
23820
7.CONNECT FUEL VAPOR FEED HOSE ASSEMBLY
Connect the fuel vapor feed hose assembly to the purge VSV and No. 1 air cleaner hose with the 2 hose clips.
Connect the fuel vapor feed hose assembly to the clamp of the No. 1 air cleaner hose.
23827A
8.CONNECT NO. 2 FUEL VAPOR FEED HOSE
Connect the No. 2 fuel vapor feed hose to the intake manifold.
9.ADD ENGINE COOLANT
10.INSPECT FOR COOLANT LEAK
11212
11.INSTALL NO. 2 CYLINDER HEAD COVER
12.PERFORM INITIALIZATION
Perform the following procedure after replacing the throttle body with motor assembly or any throttle body with motor assembly components. The following procedure should also be performed if the throttle body with motor assembly is cleaned.
Disconnect the cable from the negative (-) battery terminal. Wait at least 60 seconds and reconnect the cable.
Turn the ignition switch to ON without operating the accelerator pedal.
If the accelerator pedal is operated, perform the above step again.
Connect the GTS to the DLC3 and clear the DTCs.
for Automatic Transaxle:
Click hereEngine / Hybrid System>1NZ-FE ENGINE CONTROL>SFI SYSTEM(for Automatic Transaxle)>DTC CHECK / CLEAR
for Manual Transaxle:
Click hereEngine / Hybrid System>1NZ-FE ENGINE CONTROL>SFI SYSTEM(for Manual Transaxle)>DTC CHECK / CLEAR
Start the engine and check that the MIL is not illuminated. After the engine is warmed up, check that the idle speed is within the specified range with the A/C switch off.
| Transaxle Type | Engine Idle Speed |
|---|---|
| Automatic Transaxle | 650 to 750 rpm |
| Manual Transaxle | 600 to 700 rpm |
Turn all electrical systems and the A/C off.
Inspect the idle speed with the cooling fans off.
When checking the idle speed, the transaxle should be in neutral or park.
Enter the following menus: Powertrain / Engine and ECT / Data List / Throttle Sensor Position. Fully depress the accelerator pedal and check that the value is 60% or higher.
| Tester Display |
|---|
| Throttle Sensor Position |
Perform a road test and confirm that there are no abnormalities.