Home › Engine / Hybrid System › 1NZ-FE ENGINE CONTROL › THROTTLE BODY › 2013.08–2016.07
RM30M0E _51 Engine / Hybrid System _017071 1NZ-FE ENGINE CONTROL _0091206 THROTTLE BODY A

1NZ-FE ENGINE CONTROL  THROTTLE BODY  REMOVAL  


PROCEDURE

Hide 11212 2.REMOVE NO. 2 CYLINDER HEAD COVER

Hide 23827A 3.DISCONNECT NO. 2 FUEL VAPOR FEED HOSE

a.
A171157

Disconnect the No. 2 fuel vapor feed hose from the intake manifold.


Hide 23820 4.DISCONNECT FUEL VAPOR FEED HOSE ASSEMBLY

a.
A171158

Disconnect the fuel vapor feed hose assembly from the clamp of the No. 1 air cleaner hose.


b.

Loosen the 2 hose clips and disconnect the fuel vapor feed hose assembly from the No. 1 air cleaner hose and purge VSV.


Hide 17341T 5.DISCONNECT NO. 1 AIR HOSE (for Automatic Transaxle)

a.
A171161

Loosen the hose clip and disconnect the No. 1 air hose from the No. 1 air cleaner hose.


Hide 17735 6.REMOVE AIR CLEANER CAP WITH NO. 1 AIR CLEANER HOSE

a.
A171159

Disconnect the purge VSV connector and mass air flow meter connector.


b.

Disengage the 3 clamps to disconnect the wire harness from the air cleaner cap and purge VSV.


c.
A171160C01
2.76,1.531 2.25,1.125 2.25,1.125 2.833,0.646 true 0.927,2.302 0.813,2.969 0.813,2.969 1.313,2.771 true 2.083,1.031 2.344,1.198 0.26,0.167 10 false *a 0.646,2.906 0.958,3.063 0.313,0.156 10 false *b
*a Clamp
*b Guide


Loosen the hose clamp and disconnect the No. 1 air cleaner hose from the throttle body with motor assembly.


d.

Disengage the 2 clamps to separate the air cleaner cap from the air cleaner case sub-assembly.


e.

Disengage the 2 guides to remove the air cleaner cap with No. 1 air cleaner hose from the air cleaner case sub-assembly and throttle body with motor assembly.


Hide 16522 7.SEPARATE WATER FILLER BRACKET

a.
A171168

Remove the 2 nuts to separate the water filler bracket from the throttle body with motor assembly.


Hide 16264 8.DISCONNECT NO. 2 WATER BY-PASS HOSE

a.
A249580

Loosen the hose clip and disconnect the No. 2 water by-pass hose from the throttle body with motor assembly.


Hide 16261 9.DISCONNECT WATER BY-PASS HOSE

a.
A249581

Loosen the hose clip and disconnect the water by-pass hose from the throttle body with motor assembly.


Hide 22030 10.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

a.
A249582

Disengage the clamp to disconnect the wire harness from the wire harness clamp bracket.


b.

Disconnect the throttle body with motor assembly connector.


c.
A249583

Remove the nut and wire harness clamp bracket from the throttle body with motor assembly.


d.
A249584

Remove the bolt, 3 nuts and throttle body with motor assembly from the intake manifold.

NOTICE:

If a component has been dropped or subjected to a strong impact, replace the throttle body with motor assembly.



e.

Remove the throttle body gasket from the intake manifold.