Home › Engine / Hybrid System › 2NZ-FE EMISSION CONTROL › CANISTER › 2013.08–2016.10
RM30M0E _51 Engine / Hybrid System _017078 2NZ-FE EMISSION CONTROL _0092334 CANISTER G

2NZ-FE EMISSION CONTROL  CANISTER  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT CHARCOAL CANISTER (for Fuel Tank Cap Method)


b.

Check for clogs in the air filter (when not using GTS).

i.

Start the engine.


ii.

Warm up the engine.


iii.

Allow the engine to idle after the engine has warmed up.


iv.

After 15 minutes, open the fuel tank cap assembly to discharge the pressure in the fuel tank assembly.


v.

Close the fuel tank cap assembly and allow the engine to idle for 30 seconds.


vi.
A202994

Open the fuel tank cap assembly again and check for inhalation sounds.

OK:

No whooshing sounds (inhalation sound) are heard.


HINT:

If there is a smell of gasoline and a whooshing sound (exhalation sound) is heard, positive pressure in the fuel tank assembly is being discharged. This does not indicate a malfunction.




c.

Check for clogs in the air filter (when using the GTS).

i.

Connect the GTS to the DLC3.


ii.

Start the engine.


iii.

Turn the GTS on.


iv.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Evap Control.

Powertrain > Engine and ECT > Active Test
Tester Display
Activate the VSV for Evap Control
50004 234 6

v.

Open the fuel tank cap assembly to discharge the pressure in the fuel tank assembly.


vi.

Perform the "Activate the VSV for Evap Control" Active Test while the engine is idling.


vii.

Close the fuel tank cap assembly and allow the engine to idle for 30 seconds.


viii.

Open the fuel tank cap assembly again and check for inhalation sounds.

OK:

No whooshing sounds (inhalation sound) are heard.


HINT:

If there is a smell of gasoline and a whooshing sound (exhalation sound) is heard, positive pressure in the fuel tank assembly is being discharged. This does not indicate a malfunction.




Hide 2.INSPECT CHARCOAL CANISTER (for Vacuum Measurement Method)

a.

Visually check the charcoal canister for airtightness.

i.

Visually check the charcoal canister for cracks or damage, and check that there is no gasoline smell.



b.

Inspect the ventilation of the charcoal canister.

i.
A248554C03
1.271,0.854 0.573,1.052 true 1.615,1.51 1.354,1.979 true 0.406,0.958 0.719,1.115 0.313,0.156 10 false *a 1.177,1.917 1.49,2.073 0.313,0.156 10 false *b 2.396,1.979 2.708,2.135 0.313,0.156 10 false *c
*a Port A
*b Port B
*c Air


Open the fuel tank cap assembly, apply compressed air to port B and check that the air flows out from port A.

OK:

The air flows out from the port A.




c.

Inspect the check valve.

i.
A248555C03
1.563,1.917 1.688,1.479 true 1.313,0.677 0.979,0.406 true 0.813,0.281 1.031,0.458 0.219,0.177 10 false *a 1.448,1.917 1.719,2.073 0.271,0.156 10 false *b 2.094,1.885 2.281,2.042 0.188,0.156 10 false *c
*a Port A
*b Port B
*c Air


Open the fuel tank cap assembly, close the port A, and apply the compressed air from the port B.

OK:

Air does not flow at first. By gradually increasing the pressure, air flows when the pressure in the port reaches the specified level.



ii.
A248556C03
0.656,0.385 1,0.688 true 1.052,1.896 1.219,1.448 true 2.719,0.667 3.042,0.51 false 0.5,0.26 0.74,0.417 0.24,0.156 10 false *a 0.948,1.896 1.229,2.073 0.281,0.177 10 false *b 3.083,0.396 3.396,0.594 0.313,0.198 10 false *c
*a Port A
*b Port B
*c Vacuum Pump


Open the fuel tank cap assembly, close the port A, and apply a vacuum from the port B, using a vacuum pump.

OK:

The vacuum is maintained at first. By gradually increasing the vacuum, air flows and the vacuum decreases after the vacuum reaches the specified level.





e.
A302973C01
0.854,1.146 1.052,1 false 1.49,1.823 1.417,1.49 false 2.167,1.573 1.771,1.542 true 2.698,0.656 3.052,0.458 false 1.417,1.833 1.729,1.99 0.313,0.156 10 true *a 1.094,0.906 1.406,1.063 0.313,0.156 10 false *b 2.208,1.469 2.521,1.667 0.313,0.198 10 true *1 3.083,0.365 3.396,0.563 0.313,0.198 10 false *c
*1 No. 2 Fuel Emission Tube Sub-assembly
*a 3-way Connector
*b Hose
*c Vacuum Pump


Check for clogs in the air filter (when not using GTS).

i.

As shown in the illustration, connect the No. 2 fuel emission tube sub-assembly to the canister (fuel suction tube with pump and gauge assembly) via the 3-way connector, hose and vacuum pump.


ii.

Start the engine.


iii.

Warm up the engine.


iv.

Allow the engine to idle after the engine has warmed up.


v.

After 15 minutes, check the indicator needle on the vacuum pump.

OK:

Indicator needle of vacuum pump does not rise from its initial position.


HINT:

The indicator needle may shake due to engine vibration, etc., but if it immediately returns to its initial position, there is no problem.




f.
A302973C01
0.854,1.146 1.052,1 false 1.49,1.823 1.417,1.49 false 2.167,1.573 1.771,1.542 true 2.698,0.656 3.052,0.458 false 1.417,1.833 1.729,1.99 0.313,0.156 10 true *a 1.094,0.906 1.406,1.063 0.313,0.156 10 false *b 2.208,1.469 2.521,1.667 0.313,0.198 10 true *1 3.083,0.365 3.396,0.563 0.313,0.198 10 false *c
*1 No. 2 Fuel Emission Tube Sub-assembly
*a 3-way Connector
*b Hose
*c Vacuum Pump


Check for clogs in the air filter (when using the GTS).

i.

As shown in the illustration, connect the No. 2 fuel emission tube sub-assembly to the canister (fuel suction tube with pump and gauge assembly) via the 3-way connector, hose and vacuum pump.


ii.

Connect the GTS to the DLC3.


iii.

Start the engine.


iv.

Turn the GTS on.


v.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Evap Control.

Powertrain > Engine and ECT > Active Test
Tester Display
Activate the VSV for Evap Control
50004 234 6

vi.

Perform the "Activate the VSV for Evap Control" Active Test while the engine is idling.


vii.

Check the indicator needle on the vacuum pump.

OK:

Indicator needle of vacuum pump does not rise from its initial position.


HINT:

The indicator needle may shake due to engine vibration, etc., but if it immediately returns to its initial position, there is no problem.