Home › Brake › BRAKE (FRONT) › FRONT BRAKE
RM30M0E _54 Brake _017100 BRAKE (FRONT) _0092766 FRONT BRAKE A

BRAKE (FRONT)  FRONT BRAKE  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the LH side and RH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 43512 1.INSTALL FRONT DISC

C282653C01
2.042,1.177 2.583,1.063 2.583,1.063 2.073,1.229 true 2.625,0.969 2.938,1.125 0.313,0.156 10 false *a
*a Matchmark


a.

Align the matchmarks on front disc and front axle hub sub-assembly, and install the front disc.

NOTICE:

When replacing the front disc with a new one, select the installation position where the front disc has minimal runout.



Hide 47722 2.INSTALL FRONT DISC BRAKE CYLINDER MOUNTING

a.

Install the front disc brake cylinder mounting to the steering knuckle with the 2 bolts.

Torque:
106.8 N*m (1089 kgf*cm, 79 ft.*lbf)


Hide 3.INSTALL FRONT DISC BRAKE BUSH DUST BOOT

a.
C294088C01
0.083,0 0,0 false
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the entire circumference of 2 new front disc brake bush dust boots.

HINT:

Apply at least 0.3 g (0.01 oz.) of lithium soap base glycol grease to each front disc brake bush dust boot.



b.

Install the 2 front disc brake bush dust boots to the front disc brake cylinder mounting.


Hide 47769 4.REMOVE FRONT DISC BRAKE CYLINDER SLIDE BUSH

a.
C211757C15
0,0 3.427,0 false
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the contact surface of the front disc brake cylinder slide pin (lower side).


b.

Install a new front disc brake cylinder slide bush to the front disc brake cylinder slide pin (lower side).


Hide 47715A 5.INSTALL FRONT DISC BRAKE CYLINDER SLIDE PIN

C282663C01
0.5,0.833 0.823,0.667 false 2.083,0.833 2.469,0.625 false 2.083,1.75 2.458,1.542 false 0.5,1.75 0.823,1.583 false 0.135,0.146 0.448,0.375 0.313,0.229 12 false *A 1.74,0.135 2.052,0.385 0.313,0.25 12 false *B 0.333,0.75 0.646,0.906 0.313,0.156 10 false *1 0.333,1.667 0.646,1.823 0.313,0.156 10 false *2 1.927,0.75 2.24,0.906 0.313,0.156 10 false *1 1.917,1.667 2.229,1.823 0.313,0.156 10 false *2
*A for Rear Drum Brake
*B for Rear Disc Brake
*1 Front Disc Brake Cylinder Slide Pin (Upper Side)
*2 Front Disc Brake Cylinder Slide Pin (Lower Side)
V100155

Lithium Soap Base Glycol Grease


a.

Apply a light layer of lithium soap base glycol grease to the entire circumference of the 2 front disc brake cylinder slide pins.


b.

Install the 2 front disc brake cylinder slide pins to the front disc brake cylinder mounting.


c.

Push the 2 front disc brake cylinder slide pins into the front disc brake bush dust boot to engage the 2 front disc brake cylinder slide pins to the front disc brake bush dust boot.


Hide 04947 6.INSTALL FRONT DISC BRAKE FITTING KIT

a.
C282446C01
0.49,0.677 1.219,0.531 true 0.49,1.396 1.24,1.521 true 2.01,0.406 2.74,0.26 true 1.958,1.646 2.708,1.771 true 2.771,0.156 2.958,0.333 0.188,0.177 10 false *1 2.74,1.688 2.927,1.865 0.188,0.177 10 false *2 0.333,1.323 0.521,1.5 0.188,0.177 10 false *1 0.323,0.594 0.5,0.771 0.177,0.177 10 false *2
*1 Front No. 1 Disc Brake Pad Support Plate
*2 Front No. 2 Disc Brake Pad Support Plate


Install the 2 front No. 1 disc brake pad support plates and 2 front No. 2 disc brake pad support plates to the front disc brake cylinder mounting.

NOTICE:

Be sure to install each front disc brake pad support plate in the correct position and direction.



Hide 04945 7.INSTALL FRONT ANTI SQUEAL SHIM KIT (for Rear Drum Brake)

a.
C283828C01
1.333,1.417 1.333,1.167 false 1.833,1.667 1.833,1.417 false 0.833,1.031 0.833,0.781 false 0.333,0.802 0.333,0.552 false 2.25,0.552 2,0.552 false 1.719,0.25 1.469,0.25 false 2.5,1.271 2.5,1.021 2.5,1.021 2.333,1.021 false 3.083,1.583 3.083,1.25 3.083,1.25 2.917,1.25 false 2.271,0.479 2.583,0.635 0.313,0.156 10 false *1 0.771,1.042 1.083,1.198 0.313,0.156 10 false *2 0.271,0.813 0.583,0.969 0.313,0.156 10 false *3 1.271,1.427 1.583,1.583 0.313,0.156 10 false *4 1.771,1.677 2.083,1.833 0.313,0.156 10 false *4 1.76,0.167 2.073,0.323 0.313,0.156 10 false *1 2.167,0.938 2.479,1.094 0.313,0.156 10 false *2 2.75,1.177 3.063,1.333 0.313,0.156 10 false *3
*1 Pad Wear Indicator Plate
*2 Front No. 1 Anti Squeal Shim
*3 Front No. 2 Anti Squeal Shim
*4 Front Disc Brake Pad


Install the front No. 1 anti squeal shim and front No. 2 anti squeal shim to each front disc brake pad.

NOTICE:

Install the front anti squeal shims in the correct positions and directions.



b.

Install the pad wear indicator plate to the upper side of each front disc brake pad.


Hide 04945 8.INSTALL FRONT ANTI SQUEAL SHIM KIT (for Rear Disc Brake)

C283829C01
0,0 3.427,0 false
V100155

Disc Brake Grease


a.

Apply disc brake grease to both sides of each front No. 1 anti squeal shim.

NOTICE:
·

When replacing worn front disc brake pads, the front anti squeal shims must be replaced together with the front disc brake pads.

·

Apply disc brake grease to the area that contacts the front No. 1 anti squeal shims.




b.
C234653C01
1.458,2.563 1.458,2.188 false 0.906,2.188 0.906,1.813 false 0.542,1.979 0.542,1.604 false 2.469,2.948 2.469,2.719 false 2.906,3.073 2.906,2.948 false 2.146,1.031 2.479,1.031 false 1.938,2.823 1.938,2.448 false 1.573,0.688 1.906,0.688 false 1.948,0.583 2.094,0.729 0.146,0.146 10 false *1 1.375,2.573 1.521,2.719 0.146,0.146 10 false *4 0.823,2.198 0.969,2.344 0.146,0.146 10 false *2 0.458,1.99 0.604,2.135 0.146,0.146 10 false *3 2.385,2.958 2.531,3.104 0.146,0.146 10 false *2 2.823,3.083 2.969,3.229 0.146,0.146 10 false *3 1.896,2.823 2.042,2.969 0.146,0.146 10 false *4 2.521,0.927 2.667,1.073 0.146,0.146 10 false *1
*1 Pad Wear Indicator Plate
*2 Front No. 1 Anti Squeal Shim
*3 Front No. 2 Anti Squeal Shim
*4 Front Disc Brake Pad


Install the front No. 1 anti squeal shim and front No. 2 anti squeal shim to each front disc brake pad.

NOTICE:
·

Install the front anti squeal shims in the correct positions and directions.

·

Disc brake grease can come out slightly from the area where the front No. 1 anti squeal shim is installed.

·

Make sure that disc brake grease is not applied onto the lining surface.




c.

Install the pad wear indicator plate to the upper side of each front disc brake pad.


Hide 04465 9.INSTALL FRONT DISC BRAKE PAD

a.

Install the 2 front disc brake pads to the front disc brake cylinder mounting.

NOTICE:

There should be no oil or grease on the friction surfaces of the front disc brake pads or front disc.



Hide 47750 10.INSTALL FRONT DISC BRAKE CYLINDER ASSEMBLY

C282660C01
1.271,0.063 1.583,0.219 0.313,0.156 10 false *a 0.823,0.396 1.135,0.552 0.313,0.156 10 false *b
*a Hold
*b Turn


a.

Hold each front disc brake cylinder slide pin and install the front disc brake cylinder assembly to the front disc brake cylinder mounting with the 2 bolts.

Torque:
34 N*m (347 kgf*cm, 25 ft.*lbf)


Hide 47313A 11.CONNECT FRONT FLEXIBLE HOSE

C294082C02
1.729,1.083 2.271,0.5 true 2.323,0.406 2.635,0.604 0.313,0.198 10 false *a
*a Lock Hole


a.

Connect the front flexible hose to the front disc brake cylinder assembly with a new union bolt and a new gasket.

Torque:
30.4 N*m (310 kgf*cm, 22 ft.*lbf)

NOTICE:

Install the front flexible hose lock securely into the lock hole in the front disc brake cylinder assembly.



Hide 13.INSTALL FRONT WHEEL

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)