Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM › 2013.08–2014.03
RM30M0E _58 Vehicle Interior _017111 THEFT DETERRENT / KEYLESS ENTRY _0090853 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Theft Deterrent System Unexpectedly Sets Itself  


DESCRIPTION

A situation in which the theft deterrent system unexpectedly sets itself can be caused when the body computer cannot detect whether a door is open or closed.

If the theft deterrent system unexpectedly sets itself, there may be a malfunction in a courtesy switch, the body computer or a wire harness.

WIRING DIAGRAM

E272496
0.76,1.094 4.094,1.302 3.333,0.208 10 false Front Door Courtesy Light Switch Assembly RH 0.76,0.938 1.219,1.135 0.458,0.198 10 false F32 0.781,2.76 1.24,2.958 0.458,0.198 10 false F31 0.76,3.771 1.219,3.969 0.458,0.198 10 false F34 0.771,4.813 1.229,5.01 0.458,0.198 10 false F33 0.781,2.906 3.833,3.094 3.052,0.188 10 false Front Door Courtesy Light Switch Assembly LH 0.76,3.917 3.75,4.094 2.99,0.177 10 false Rear Door Courtesy Light Switch Assembly RH 0.76,4.958 3.76,5.167 3,0.208 10 false Rear Door Courtesy Light Switch Assembly LH 1.646,0.594 1.802,0.792 0.156,0.198 10 false 1 4.323,0.49 4.479,0.688 0.156,0.198 10 false 1 1.667,2.344 1.823,2.542 0.156,0.198 10 false 1 1.656,3.385 1.813,3.583 0.156,0.198 10 false 1 1.646,4.427 1.802,4.625 0.156,0.198 10 false 1 4.26,0.688 4.573,0.885 0.313,0.198 10 false 2N 5.615,0.677 5.927,0.875 0.313,0.198 10 false MB 5.646,0.521 5.958,0.719 0.313,0.198 10 false 18 5.938,0.677 6.552,0.875 0.615,0.198 10 false DCTY 5.938,2.469 6.552,2.667 0.615,0.198 10 false PCTY 5.604,2.49 6.063,2.688 0.458,0.198 10 false F52 5.646,2.302 5.958,2.5 0.313,0.198 10 false 14 4.219,1.594 5.896,1.99 1.677,0.396 10 false Driver Side Junction Block Assembly 5.854,4.677 6.896,4.896 1.042,0.219 10 false Body Computer

CAUTION / NOTICE / HINT

NOTICE:

The theft deterrent system is also set when doors are locked by the auto lock function of the wireless door lock system.


PROCEDURE

1.CHECK WIRELESS DOOR LOCK SYSTEM OPERATION
a.

Check that the auto lock function of the wireless door lock system can be canceled.

i.

Unlock the doors using wireless operation or entry operation.


ii.

Within 30 seconds, open and close one of the doors.



Result:
Result Proceed to
Door locks are locked. A
Door locks are not locked. B



A

2.CHECK ILLUMINATED ENTRY SYSTEM OPERATION

B

END (SYSTEM NORML)

2.CHECK ILLUMINATED ENTRY SYSTEM OPERATION
a.

Set the map light to the DOOR position.


b.

Turn the engine switch off.


c.

Open and close each door and check that the map light illuminates.

NOTICE:

The illuminated entry system illuminates the map light for 15 seconds after the door is opened and closed.



Result:
Result Proceed to
Does not illuminate for front door RH only. A
Does not illuminate for front door LH only. B
Does not illuminate for rear door RH only. C
Does not illuminate for rear door LH only. D
Illuminates for all doors. E



A

3.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY RH

B

6.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY LH

C

8.INSPECT REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY RH

D

10.INSPECT REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY LH

E

3.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY RH
a.

Remove the front door courtesy light switch assembly RH.

Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>REMOVAL


b.

Inspect the front door courtesy light switch assembly RH.

Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY RH - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)

NG

REPLACE FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY RH

4.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY RH - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the F32 front door courtesy light switch assembly RH connector.


b.

Disconnect the 2N driver side junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F32-1 - 2N-1 Always Below 1 Ω
F32-1 or 2N-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY

b.

Disconnect the driver side junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

B343154
2.531,0.625 2.823,0.802 0.292,0.177 5.552,0.51 5.844,0.688 0.292,0.177 2.271,1.448 2.229,1.156 true 0.094,0.094 0.406,0.292 0.313,0.198 10 false *a 2.573,0.635 2.885,0.833 0.313,0.198 10 false MB 5.615,0.521 5.927,0.719 0.313,0.198 10 false 2N 2.094,1.458 2.583,1.646 0.49,0.188 10 false DCTY
*a Component without harness connected
(Driver Side Junction Block Assembly)
- -


Standard Resistance:
Tester Connection Condition Specified Condition
2N-1 - MB-18 (DCTY) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLY

6.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY LH
a.

Remove the front door courtesy light switch assembly LH.

Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>REMOVAL


b.

Inspect the front door courtesy light switch assembly LH.

Click hereVehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY LH - BODY COMPUTER)

NG

REPLACE FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY LH

7.CHECK HARNESS AND CONNECTOR (FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY LH - BODY COMPUTER)
a.

Disconnect the F31 front door courtesy light switch assembly LH connector.


b.

Disconnect the F52 body computer connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F31-1 - F52-14 (PCTY) Always Below 1 Ω
F31-1 or F52-14 (PCTY) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY RH
a.

Remove the rear door courtesy light switch assembly RH.

Click hereVehicle Interior>LIGHTING (INT)>REAR DOOR COURTESY SWITCH>REMOVAL


b.

Inspect the rear door courtesy light switch assembly RH.

Click hereVehicle Interior>LIGHTING (INT)>REAR DOOR COURTESY SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY RH - BODY COMPUTER)

NG

REPLACE REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY RH

9.CHECK HARNESS AND CONNECTOR (REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY RH - BODY COMPUTER)
a.

Disconnect the F34 rear door courtesy light switch assembly RH connector.


b.

Disconnect the F52 body computer connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F34-1 - F52-14 (PCTY) Always Below 1 Ω
F34-1 or F52-14 (PCTY) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY LH
a.

Remove the rear door courtesy light switch assembly LH.

Click hereVehicle Interior>LIGHTING (INT)>REAR DOOR COURTESY SWITCH>REMOVAL


b.

Inspect the rear door courtesy light switch assembly LH.

Click hereVehicle Interior>LIGHTING (INT)>REAR DOOR COURTESY SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY LH - BODY COMPUTER)

NG

REPLACE REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY LH

11.CHECK HARNESS AND CONNECTOR (REAR DOOR COURTESY LIGHT SWITCH ASSEMBLY LH - BODY COMPUTER)
a.

Disconnect the F33 rear door courtesy light switch assembly LH connector.


b.

Disconnect the F52 body computer connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F33-1 - F52-14 (PCTY) Always Below 1 Ω
F33-1 or F52-14 (PCTY) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR