A situation in which the alarm is armed but does not sound when the luggage door or engine hood is opened can be caused when the body computer cannot detect whether the luggage compartment door courtesy light switch or engine hood courtesy switch is open or closed.
If the alarm does not sound, there may be a malfunction in the luggage compartment door courtesy light switch, engine hood courtesy switch, body computer or a wire harness.
Close all doors, the luggage compartment door and the engine hood.
Lock the doors using the wireless operation or entry operation.
Check that the security indicator light illuminates.
After 30 seconds have elapsed, check that the security indicator light changes from illuminated to flashing.
The illumination status of the security indicator light can be used to determine whether the theft deterrent system is set or unset.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Open the driver side window.
Set the theft deterrent system.
Close all doors, the luggage compartment door and the engine hood.
Lock the doors using wireless operation or entry operation.
Wait for 30 seconds or more.
After 30 seconds have elapsed, open the luggage compartment door or engine hood.
Opening any of the doors will cause the alarm to sound, so do not open or close the doors.
| Result | Proceed to |
|---|---|
| Alarm does not sound when luggage compartment door is opened. | A |
| Alarm does not sound when engine hood is opened. | B |
A
B
Remove the luggage compartment door lock assembly.
Click hereVehicle Interior>LIGHTING (INT)>BACK DOOR COURTESY SWITCH(for Sedan)>REMOVAL
Inspect the luggage compartment door lock assembly.
Click hereVehicle Interior>LIGHTING (INT)>BACK DOOR COURTESY SWITCH(for Sedan)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the L5 luggage compartment door lock assembly connector.
Disconnect the 2N driver side junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L5-3 (D+) - 2N-3 | Always | Below 1 Ω |
| L5-2 (ACT-) - Body ground | Always | Below 1 Ω |
| L5-3 (D+) or 2N-3 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the body computer.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Disconnect the driver side junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| *a | Component without harness connected
(Driver Side Junction Block Assembly) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2N-3 - MB-21 (LGCY) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the hood lock assembly.
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE HOOD COURTESY SWITCH>REMOVAL
Inspect the hood lock assembly.
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE HOOD COURTESY SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A29 hood lock assembly connector.
Disconnect the 2D driver side junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A29-1 - 2D-9 | Always | Below 1 Ω |
| A29-2 - Body ground | Always | Below 1 Ω |
| A29-1 or 2D-9 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the body computer.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Disconnect the driver side junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| *a | Component without harness connected
(Driver Side Junction Block Assembly) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2D-9 - MB-20 (HCTY) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG