Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM › 2013.08–2014.03
RM30M0E _58 Vehicle Interior _017111 THEFT DETERRENT / KEYLESS ENTRY _0090853 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Security Indicator Light does not Operate Correctly  


DESCRIPTION

When the theft deterrent system is in the arming preparation state, the body computer uses the communication line to send an illumination request to the certification ECU (smart key ECU assembly), and the certification ECU (smart key ECU assembly) illuminates the security indicator light.

When the theft deterrent system changes from the arming preparation state to armed state, the security indicator light changes from illuminated to flashing.

WIRING DIAGRAM

E281130E01
1.021,1.615 2.51,1.833 1.49,0.219 10 false Security Indicator Light 0.854,2.115 2.698,2.333 1.844,0.219 10 false Combination Meter Assembly 0.854,1.969 1.188,2.135 0.333,0.167 10 false F38 3.083,1.365 3.417,1.531 0.333,0.167 10 false F43 4.385,0.813 4.719,0.979 0.333,0.167 10 false F44 4.396,1.865 4.729,2.031 0.333,0.167 10 false F44 3.938,1.875 4.375,2.052 0.438,0.177 10 false RDA3 3.938,0.813 4.375,0.969 0.438,0.156 10 false PRG3 3.406,1.365 3.74,1.531 0.333,0.167 10 false IND 5.813,0.802 6.188,0.99 0.375,0.188 10 false PRG 5.813,1.854 6.167,2.031 0.354,0.177 10 false RDA 5.531,1.76 5.865,1.927 0.333,0.167 10 false 16 5.615,0.708 5.865,0.896 0.25,0.188 10 false 9 4.417,0.656 4.667,0.844 0.25,0.188 10 false 36 4.438,1.698 4.688,1.885 0.25,0.188 10 false 13 3.125,1.198 3.375,1.385 0.25,0.188 10 false 15 2.781,1.26 3.031,1.448 0.25,0.188 10 false 13 2.521,1.26 2.771,1.448 0.25,0.188 10 false LP 0.802,1.271 1.052,1.458 0.25,0.188 10 false ED 0.552,1.271 0.802,1.458 0.25,0.188 10 false 21 3.094,2.688 4.625,3.25 1.531,0.563 10 false Certification ECU (Smart Key ECU Assembly) 5.781,2.813 6.771,3.094 0.99,0.281 10 false Body Computer 5.792,2.667 6.094,2.833 0.302,0.167 10 false F52

CAUTION / NOTICE / HINT

NOTICE:

As the security indicator light is shared with the immobiliser system, even if the theft deterrent system is canceled, the security indicator light will blink if the immobiliser system is set.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BODY COMPUTER - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Disconnect the F52 body computer connector.


b.

Disconnect the F44 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F52-9 (PRG) - F44-36 (PRG3) Always Below 1 Ω
F52-16 (RDA) - F44-13 (RDA3) Always Below 1 Ω
F52-9 (PRG) or F44-36 (PRG3) - Body ground Always 10 kΩ or higher
F52-16 (RDA) or F44-13 (RDA3) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.REPLACE BODY COMPUTER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.REPLACE BODY COMPUTER
a.

Replace the body computer with a new or known good one.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

3.CHECK SECURITY INDICATOR LIGHT OPERATION (IMMOBILISER SYSTEM)
3.CHECK SECURITY INDICATOR LIGHT OPERATION (IMMOBILISER SYSTEM)
a.

Close all doors, the luggage compartment door and the engine hood.


b.

Lock the doors using wireless operation or entry operation.


c.

Check that the security indicator light illuminates.


d.

After 30 seconds have elapsed, check that the security indicator light changes from illuminated to flashing.


Result:
Proceed to
OK
NG



OK

END (BODY COMPUTER WAS DEFECTIVE)

NG