Home › Drivetrain › U340E AUTOMATIC TRANSMISSION / TRANSAXLE › DIFFERENTIAL CASE › 2013.12–2016.10
RM30M0E _52 Drivetrain _017087 U340E AUTOMATIC TRANSMISSION / TRANSAXLE _0090617 DIFFERENTIAL CASE A

U340E AUTOMATIC TRANSMISSION / TRANSAXLE  DIFFERENTIAL CASE  REASSEMBLY  


PROCEDURE

Hide 41039A 1.INSTALL DIFFERENTIAL GEAR KIT

a.
C282886

Coat the sliding and rotating surfaces of the differential gear kit (2 front differential pinions and 2 front differential side gears), 2 front differential side gear thrust washers and 2 front differential pinion thrust washers with Toyota Genuine ATF WS.


b.

Install the 2 front differential side gear thrust washers to the 2 front differential side gears.


c.

Install the 2 front differential side gears, 2 front differential pinions and 2 front differential pinion thrust washers to the front differential case.

HINT:

Rotating each front differential side gear, install the 2 front differential pinions and 2 front differential pinion thrust washers.



Hide 41342F 2.INSTALL FRONT NO. 1 DIFFERENTIAL PINION SHAFT

a.
C282887

Coat the front No. 1 differential pinion shaft with Toyota Genuine ATF WS.


b.

Install the front No. 1 differential pinion shaft to the front differential case so that the hole for the front differential pinion shaft straight pin is aligned with the hole in the front differential case.


Hide 3.INSPECT FRONT DIFFERENTIAL SIDE GEAR BACKLASH

Hide 41342A 4.INSTALL FRONT DIFFERENTIAL PINION SHAFT STRAIGHT PIN

a.
C282888

Using a 5 mm pin punch and a hammer, install the front differential pinion shaft straight pin to the front differential case.


b.
C282889

Using a chisel and a hammer, stake the front differential case hole.


Hide 41221 5.INSTALL FRONT DIFFERENTIAL RING GEAR

a.
C166738C01
1.063,0.417 1.281,0.615 0.219,0.198 10 false *a
*a 90 to 110°C (194 to 230°F)


Using Toyota Genuine ATF WS and a heater, heat the front differential ring gear to 90 to 110°C (194 to 230°F).

CAUTION:

Use thick gloves to protect your hands as the front differential ring gear is hot.


NOTICE:

Do not heat the ring gear to more than 110°C (230°F).



b.

Clean the contact surfaces of the front differential case and front differential ring gear.


c.
C298046C01
1.76,1.625 2.708,1.719 2.708,1.719 1.76,1.542 true 2.771,1.646 3.083,1.802 0.313,0.156 10 false *a
*a Matchmark


Align the matchmarks on the front differential ring gear and front differential case, and quickly install them.


d.
C282879

Secure the front differential case in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



e.

Install 4 new front differential ring gear set bolt lock plates and 8 bolts.

Torque:
88.2 N*m (899 kgf*cm, 65 ft.*lbf)

NOTICE:

Tighten the bolts after the front differential ring gear has cooled down sufficiently.



f.
C282891E01
1.104,0.594 1.5,0.323 false 1.552,0.219 2.01,0.417 0.458,0.198 10 false SST

Using SST and a hammer, stake the 4 front differential ring gear set bolt lock plates.

SST
09930-00010  


Hide 41311F 6.INSTALL FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING

a.
C282892E01
1.917,1.021 2.313,0.542 2.313,0.542 1.75,0.542 true 2.375,0.469 2.833,0.667 0.458,0.198 10 false SST

Using SST and a press, install the front differential case rear tapered roller bearing inner race to the front differential case.

SST
09726-40010  
09950-60020  (09951-00790)


b.
C282976E01
1.5,0.688 1.031,0.438 1.031,0.438 1.438,0.885 true 1.594,1.531 2.25,1.802 2.25,1.802 2.438,1.323 true 0.75,0.333 1.208,0.531 0.458,0.198 10 false SST 2.125,1.854 2.583,2.052 0.458,0.198 10 false SST

Using SST and a press, install the front differential case rear shim and front differential case rear tapered roller bearing outer race to the transaxle case.

SST
09950-60010  (09951-00650)
09950-60020  (09951-00720)
09950-70010  (09951-07100, 09951-07200)


Hide 33481X 7.INSTALL SPEEDOMETER DRIVE GEAR (w/ Speedometer Drive Gear)

a.
C284796

Install the speedometer drive gear to the front differential case.


Hide 41311E 8.INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING

a.
C283043E01
1.823,0.729 2.208,0.438 2.208,0.438 1.771,0.51 false 2.26,0.344 2.719,0.542 0.458,0.198 10 false SST

Using SST and a press, install the front differential case front tapered roller bearing inner race to the front differential case.

SST
09950-60010  (09951-00460)
09950-70010  (09951-07100)


b.
C282968E01
1.688,1.76 2.594,0.75 2.594,0.75 1.531,1.365 true 2.656,0.677 3.115,0.875 0.458,0.198 10 false SST

Using SST and a press, install the front differential case front tapered roller bearing outer race to the transaxle housing.

SST
09950-60020  (09951-00680)
09950-70010  (09951-07150)