Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › FRONT AIRBAG SENSOR › 2014.03–2017.10
RM30M0E _58 Vehicle Interior _017115 SUPPLEMENTAL RESTRAINT SYSTEMS _0092018 FRONT AIRBAG SENSOR A

SUPPLEMENTAL RESTRAINT SYSTEMS  FRONT AIRBAG SENSOR  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


PROCEDURE

Hide 89173 1.INSTALL FRONT AIRBAG SENSOR

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Before connecting the connector, check that the position of the white housing lock is correct as shown in the illustration.

B296255C01
4.76,1.833 5.042,2.073 0.281,0.24 10 false *b 1.396,1.833 1.729,2.125 0.333,0.292 10 false *b 4.76,0.573 5.052,0.885 0.292,0.313 10 false *a 1.396,0.573 1.656,0.844 0.26,0.271 10 false *a
*a Incorrect *b Correct



d.

Insert the pin (stopper) into the body hole and install the front airbag sensor to the vehicle body with the bolt.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)

NOTICE:
·

If the front airbag sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.

·

When installing the front airbag sensor, be careful that the SRS wiring does not interfere with or is not pinched between other parts.

·

Make sure that the pin (stopper) is securely inserted into the body hole.

·

Tighten the bolt while holding the front airbag sensor because the front airbag sensor pin (stopper) is easily damaged.




e.

Connect the connector to the front airbag sensor.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.


i.

Be sure to engage the connectors until they are locked (when locking, make sure that a click sound can be heard).

B312074C06
2.208,0.802 2.573,0.563 true 2.406,1 2.781,0.771 true 2.469,1.396 2.469,1.719 false 2.813,0.667 3.021,0.875 0.208,0.208 10 false *1 2.396,1.729 2.708,1.885 0.313,0.156 10 false *2 5.938,3.365 6.25,3.521 0.313,0.156 10 false *a 2.615,0.438 2.865,0.667 0.25,0.229 10 false (A)
*1 White Housing Lock *2 Yellow CPA
*a Connection is Completed - -


HINT:

When engaged, the white housing lock will slide. Be sure not to hold the white housing lock or part (A), as it may result in an insecure fit.




f.

Check that there is no looseness in the installation parts of the front airbag sensor.


Hide 89175 2.INSTALL AIRBAG SENSOR BRACKET

a.

Engage the hook to install the airbag sensor bracket.


b.

Install the bolt.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 53141F 3.INSTALL RADIATOR COVER (for Sedan)

Hide 53141F 4.INSTALL RADIATOR COVER (for Hatchback)

Hide 5.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected. (for Hatchback)

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION