Wear protective gloves. Sharp areas on the parts may injure your hands.
The procedure described below is for the LHD side. Use the same procedure for both the LHD and RHD side, unless otherwise specified.
The procedure described below is for the driver side. Use the same procedure for both the driver and front passenger sides, unless otherwise specified.
1.INSTALL SEAT ADJUSTER COVER CAP
Install the 2 seat adjuster cover caps.
72211C
2.INSTALL SEAT TRACK ADJUSTING HANDLE
Engage the 2 springs to install the seat track adjusting handle to the separate type front seat cushion spring assembly LH.
71014S
3.INSTALL FRONT SEATBACK FRAME SUB-ASSEMBLY LH
Install the front seatback frame sub-assembly LH to the separate type front seat cushion spring assembly LH with the 4 bolts.
71874A
4.INSTALL FRONT SEAT LOWER CUSHION SHIELD (w/ Vertical Adjuster)
Engage the 2 claws to install the front seat lower cushion shield.
71874
5.INSTALL FRONT SEAT LOWER CUSHION SHIELD LH (w/ Vertical Adjuster)
Engage the clip to install the front seat lower cushion shield LH.
Engage the hook as shown in the illustration.
Install the screw.
71873
6.INSTALL FRONT SEAT LOWER CUSHION SHIELD RH (w/ Vertical Adjuster)
Use the same procedure as for the LH side.
71538A
7.INSTALL FRONT SEAT CUSHION EDGE PROTECTOR LH
Engage the 2 guides to install the front seat cushion edge protector LH.
71537G
8.INSTALL FRONT SEAT CUSHION EDGE PROTECTOR RH
Use the same procedure as for the LH side.
71074S
9.INSTALL SEPARATE TYPE FRONT SEATBACK COVER
| *1 | Hog Ring |
| *a | Hog Ring Pliers |
Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 6 new hog rings.
Be careful not to damage the separate type front seatback cover.
When installing the hog rings, take care to minimize wrinkles as much as possible.
Align the center of the hog ring installation area of the separate type front seatback cover with the center of the separate type front seatback pad so that no wrinkles appear, and securely tighten the hog rings as shown in the illustration.
10.INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD
Install the separate type front seatback cover with pad to the front seatback frame sub-assembly LH.
| *a | Protruding |
Align the protruding portion of the front seat headrest support with the installation groove of the front seatback frame sub-assembly LH.
Engage the 4 claws to install the 2 front seat headrest supports.
| *1 | Hog Ring |
| *a | Hog Ring Pliers |
Using hog ring pliers, install 3 new hog rings.
Be careful not to damage the separate type front seatback cover.
When installing the hog rings, take care to minimize wrinkles as much as possible.
Securely tighten the hog rings as shown in the illustration.
| *1 | Hog Ring |
| *a | Hog Ring Pliers |
Using hog ring pliers, install 4 new hog rings.
Be careful not to damage the separate type front seatback cover.
When installing the hog rings, take care to minimize wrinkles as much as possible.
Securely tighten the hog rings as shown in the illustration.
71072S
11.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER
| *1 | Hog Ring |
| *a | Hog Ring Pliers |
Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 16 new hog rings.
Be careful not to damage the separate type front seat cushion cover.
When installing the hog rings, take care to minimize wrinkles as much as possible.
Align the center of the hog ring installation area of the separate type front seat cushion cover with the center of the separate type front seat cushion pad so that no wrinkles appear, and securely tighten the hog rings as shown in the illustration.
| *1 | Hog Ring |
| *a | Hog Ring Pliers |
Using hog ring pliers, install 2 new hog rings.
Be careful not to damage the separate type front seat cushion cover.
When installing the hog rings, take care to minimize wrinkles as much as possible.
Tighten the hog rings as shown in the illustration.
12.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD
w/ Vertical Adjuster:
Place the separate type front seat cushion cover with pad to the separate type front seat cushion spring assembly.
Engage the 3 hooks.
w/o Vertical Adjuster:
Place the separate type front seat cushion cover with pad to the separate type front seat cushion spring assembly.
Engage the 2 hooks.
Engage the 5 hooks.
Engage the 3 hooks to install the separate type front seat cushion cover with pad.
for Front Passenger Side:
Engage the 4 hooks
71862
13.INSTALL FRONT SEAT CUSHION INNER SHIELD
Engage the claw and 3 guides to install the front seat cushion inner shield.
71812D
14.INSTALL FRONT SEAT CUSHION SHIELD LH
Engage the claw, 3 guides and 2 clips to install the front seat cushion shield LH.
72495
15.INSTALL VERTICAL ADJUSTING HANDLE (w/ Vertical Adjuster)
Install the vertical adjusting handle with the screw.
72526A
16.INSTALL RECLINING ADJUSTER RELEASE HANDLE
Engage the claw to install the reclining adjuster release handle.
73240
17.INSTALL FRONT SEAT INNER BELT ASSEMBLY LH (for Driver Side)
for LHD: Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>INSTALLATION
for RHD: Click hereVehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>INSTALLATION
73230
18.INSTALL FRONT SEAT INNER BELT ASSEMBLY RH (for Front Passenger Side)
71910A
19.INSTALL FRONT SEAT HEADREST ASSEMBLY
Install the front seat headrest assembly.