71078S
1.INSTALL SEPARATE TYPE REAR SEATBACK COVER LH (for LH Side)
w/o Armrest:
| *1 | Hog Ring |
| *a | Hog Ring Pliers |
Using hog ring pliers, install the separate type rear seatback cover LH to the separate type rear seatback pad LH with 8 new hog rings.
Be careful not to damage the separate type rear seatback cover LH.
When installing the hog rings, take care to minimize wrinkles as much as possible.
Align the center of the hog ring installation area of the separate type rear seatback cover LH with the center of the separate type rear seatback pad LH so that no wrinkles appear, and securely tighten the hog rings as shown in the illustration.
w/ Armrest:
| *1 | Hog Ring |
| *a | Hog Ring Pliers |
Using hog ring pliers, install the separate type rear seatback cover LH to the separate type rear seatback pad LH with 16 new hog rings.
Be careful not to damage the separate type rear seatback cover LH.
When installing the hog rings, take care to minimize wrinkles as much as possible.
Align the center of the hog ring installation area of the separate type rear seatback cover LH with the center of the separate type rear seatback pad LH so that no wrinkles appear, and securely tighten the hog rings as shown in the illustration.
71077S
2.INSTALL SEPARATE TYPE REAR SEATBACK COVER RH (for RH Side)
| *1 | Hog Ring |
| *a | Hog Ring Pliers |
Using hog ring pliers, install the separate type rear seatback cover RH to the separate type rear seatback pad RH with 8 new hog rings.
Be careful not to damage the separate type rear seatback cover RH.
When installing the hog rings, take care to minimize wrinkles as much as possible.
Align the center of the hog ring installation area of the separate type rear seatback cover RH with the center of the separate type rear seatback pad RH so that no wrinkles appear, and securely tighten the hog rings as shown in the illustration.
3.INSTALL SEPARATE TYPE REAR SEATBACK COVER WITH PAD LH (for LH Side)
Install the rear seatback lock pin.
Clean the threads of the rear seatback lock pin with non-residue solvent.
Apply adhesive to the threads of the rear seatback lock pin.
Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
Using a T40 "TORX" socket wrench, install the rear seatback lock pin.
Temporarily install the separate type rear seatback cover with pad LH to the rear seatback frame sub-assembly LH.
w/ Rear Center Seat Headrest:
| *a | Protruding |
Align the protruding portion of the rear seat headrest support with the installation groove of the rear seatback frame sub-assembly LH.
Engage the 8 claws to install the 4 rear seat headrest supports.
w/o Rear Center Seat Headrest:
| *a | Protruding |
Align the protruding portion of the rear seat headrest support with the installation groove of the rear seatback frame sub-assembly LH.
Engage the 4 claws to install the 2 rear seat headrest supports.
| *a | Zipper |
| *b | Hook |
Fasten the zipper and engage the hook.
4.INSTALL SEPARATE TYPE REAR SEATBACK COVER WITH PAD RH (for RH Side)
Install the rear seatback lock pin.
Clean the threads of the rear seatback lock pin with non-residue solvent.
Apply adhesive to the threads of the rear seatback lock pin.
Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
Using a T40 "TORX" socket wrench, install the rear seatback lock pin.
Temporarily install the separate type rear seatback cover with pad RH to the rear seatback frame sub-assembly RH.
| *a | Protruding |
Align the protruding portion of the rear seat headrest support with the installation groove of the rear seatback frame sub-assembly RH.
Engage the 4 claws to install the 2 rear seat headrest supports.
| *a | Zipper |
| *b | Hook |
Fasten the zipper and engage the hook.
73344
5.INSTALL REAR SEAT SHOULDER BELT GUIDE LH (for Sedan LH Side)
Use the same procedure for both sides. (for 3 Point Type Rear Center Seat Belt)
Engage the guide to install the rear seat shoulder belt guide LH.
Install the 2 screws.
73343
6.INSTALL REAR SEAT SHOULDER BELT GUIDE RH (for Sedan RH Side)
Engage the guide to install the rear seat shoulder belt guide RH.
Install the 2 screws.
66990
7.INSTALL CUP HOLDER ASSEMBLY (w/ Armrest)
Engage the 4 guides to install the cup holder assembly.
72830
8.INSTALL REAR SEAT CENTER ARMREST ASSEMBLY (w/ Armrest)
Install the bush to the rear seat center armrest assembly.
Engage the guide to install the rear seat center armrest assembly.
Install the bush, wave washer and bolt.
72868B
9.INSTALL CENTER ARMREST HINGE COVER (w/ Armrest)
Engage the 2 guides and claw to install the center armrest hinge cover.
71960B
10.INSTALL REAR SEAT CENTER HEADREST ASSEMBLY (w/ Rear Center Seat Headrest)
Install the rear seat center headrest assembly.
71940A
11.INSTALL REAR SEAT HEADREST ASSEMBLY
Install the 2 rear seat headrest assemblies.
71075B
12.INSTALL BENCH TYPE REAR SEAT CUSHION COVER