Home › Vehicle Interior › SEAT › REAR SEAT ASSEMBLY(for Fold Down Seat Type) › 2014.03–2017.10
RM30M0E _58 Vehicle Interior _017116 SEAT _0116069 REAR SEAT ASSEMBLY(for Fold Down Seat Type) A

SEAT  REAR SEAT ASSEMBLY(for Fold Down Seat Type)  REASSEMBLY  


PROCEDURE

Hide 71077B 1.INSTALL BENCH TYPE REAR SEATBACK COVER

a.
B348215C01
1.74,3.844 1.906,4.167 false 0.573,2.823 0.688,2.948 false 0.427,2.688 0.74,2.844 0.313,0.156 10 false *1 1.906,4.188 2.219,4.344 0.313,0.156 10 false *a
*1 Hog Ring
*a Hog Ring Pliers


Using hog ring pliers, install the bench type rear seatback cover to the bench type seatback pad with 16 new hog rings.

NOTICE:
·

Be careful not to damage the bench type rear seatback cover.

·

When installing the hog rings, take care to minimize wrinkles as much as possible.

·

Align the center of the hog ring installation area of the bench type rear seatback cover with the center of the bench type rear seatback pad so that no wrinkles appear, and securely tighten the hog rings as shown in the illustration.




Hide 2.INSTALL BENCH TYPE REAR SEATBACK COVER WITH PAD

a.

Install the rear seatback lock pin.

HINT:

Use the same procedure for both sides.


i.

Clean the threads of the rear seatback lock pin with non-residue solvent.


ii.

Apply adhesive to the threads of the rear seatback lock pin.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



iii.
B362155

Using a T40 "TORX" socket wrench, install the rear seatback lock pin.

Torque:
32 N*m (326 kgf*cm, 24 ft.*lbf)



b.

Temporarily install the bench type rear seatback cover with pad to the rear seatback frame sub-assembly.


c.

w/ Rear Center Seat Headrest:

i.
B348216C01
1.25,0.521 1.188,0.271 false 2.667,0.802 2.74,0.552 false 1.208,0.531 1.521,0.688 0.313,0.156 10 false *a 2.563,0.813 2.875,0.969 0.313,0.156 10 false *a
*a Protruding


Align the protruding portion of the rear seat headrest support assembly with the installation groove of the bench type rear seatback frame sub-assembly.


ii.

Engage the 12 claws to install the 6 rear seat headrest support assemblies.



d.

w/o Rear Center Seat Headrest:

i.
B345184
0.5,0.448 0.469,0.229 false 1.99,0.75 2.031,0.521 false 0.427,0.458 0.74,0.656 0.313,0.198 10 false *a 1.896,0.75 2.208,0.948 0.313,0.198 10 false *a
*a Protruding


Align the protruding portion of the rear seat headrest support assembly with the installation groove of the bench type rear seatback pad.



e.
B348211C01
0.073,0.865 0.292,1.208 0.219,0.344 10 true *a 3.146,0.938 3.365,1.281 0.219,0.344 10 true *a 1.625,1.833 1.958,2.073 0.333,0.24 10 true *b
*a Zipper
*b Hook


Fasten the 2 zippers and engage the hook.


Hide 71960B 3.INSTALL REAR SEAT CENTER HEADREST ASSEMBLY (w/ Rear Center Seat Headrest)

a.

Install the rear seat center headrest assembly.


Hide 71940A 4.INSTALL REAR SEAT HEADREST ASSEMBLY

a.

Install the 2 rear seat headrest assemblies.


Hide 71075B 5.INSTALL BENCH TYPE REAR SEAT CUSHION COVER